Changes

[[image:Ul_rs232.png]]

[[image:Ul_rs232.png]]

<br><br>

<br><br>

To receive UL202 Fuel Sensor information to the configured server, the Ultrasonic UL202 Fuel level and status have to be enabled in “I/O” section. <br><br>

To receive UL202 Fuel Sensor information to the configured server, the Ultrasonic UL202 Fuel level and status have to be enabled in the “I/O” section. <br><br>

[[image:Ul_io.png]]

[[image:Ul_io.png]]

[[image:FMB125 UL1.png]]

[[image:FMB125 UL1.png]]

To receive UL202 Fuel Sensor information to the configured server, Ultrasonic UL202-2 Fuel level and status have to be enabled in the “I/O” section. <br>

To receive UL202 Fuel Sensor information to the configured server, the Ultrasonic UL202-2 Fuel level and status have to be enabled in the “I/O” section. <br>

[[image:FMB125_UL2.png]]

[[image:FMB125_UL2.png]]

==FM63XY/FMB630 configuration==

==FM63XY/FMB630 configuration==

With FM63 00.03.XX version, FM63XY/FMB630 can support Ultrasonic UL202 Fuel sensors. In order to configure device to read UL202 Sensor information, COM1/2 port has to be selected as “UL202-2 Fuel Sensor”.  <br>

With FM63 00.03.XX version, FM63XY/FMB630 can support Ultrasonic UL202 Fuel sensors. In order to configure the device to read UL202 Sensor information, the COM1/2 port has to be selected as “UL202-2 Fuel Sensor”.  <br>

[[image:FM63_UL1.png]]

[[image:FM63_UL1.png]]

To receive UL202 Fuel Sensor information to the configured server, in preferred device Profile Ultrasonic UL202-2 Fuel level and status have to be enabled in the “I/O” section. <br>

To receive UL202 Fuel Sensor information to the configured server, in preferred device Profile Ultrasonic UL202-2 Fuel level and status have to be enabled in the “I/O” section. <br>

# The customers need to prepare: 12V power supply, isolating tape, and duster cloth and paper tissue (used to wipe off grease dirt).<br>

# The customers need to prepare: 12V power supply, isolating tape, and duster cloth and paper tissue (used to wipe off grease dirt).<br>

# Before installing on the vehicle, ensure that the vehicle is at the horizontal ground and the fuel tank is placed on frame horizontally.<br>  

# Before installing on the vehicle, ensure that the vehicle is at the horizontal ground and the fuel tank is placed on frame horizontally.<br>  

# The installation area of the probe should avoid the fuel filler, fuel outlet, fuel return pipe, fuel float and baffle.<br>

# The installation area of the probe should avoid the fuel filler, fuel outlet, fuel return pipe, fuel float, and baffle.<br>

# Select the flat part at fuel tank bottom or close to the central area as possible.<br>

# Select the flat part at the fuel tank bottom or as close to the central area as possible.<br>

# For circular oil tank, in addition to avoiding the barrier, the tangent plane closest to the ground should be selected.<br> [[image:Ulll.png|300px]]

# For circular oil tank, in addition to avoiding the barrier, the tangent plane closest to the ground should be selected.<br> [[image:Ulll.png|300px]]

# Connect the main body of the sensor with user interface line, extension line, probe connection line.<br>

# Connect the main body of the sensor with user interface line, extension line, probe connection line.<br>

# Hold down “Key 1 for more than 8 seconds and release it to enter input state of total fuel tank height. F030 in the figure below means that the total height of the fuel tank is 30cm. Press “Key 2” to increase and press “Key 3” to decrease. Hold down “key 1” for 8 seconds to confirm the parameters. <br>

# Hold down “Key 1 for more than 8 seconds and release it to enter input state of total fuel tank height. F030 in the figure below means that the total height of the fuel tank is 30cm. Press “Key 2” to increase and press “Key 3” to decrease. Hold down “key 1” for 8 seconds to confirm the parameters. <br>

# After the total height of the fuel tank is put properly, it enters the input state for the current liquid level of the oil tank. E030 in the figure below means that the current liquid level height is 30cm. Press “key 2” to increase and press “key 3” to decrease.<br>[[image:Ell2.png|300px]]

# After the total height of the fuel tank is put properly, it enters the input state for the current liquid level of the oil tank. E030 in the figure below means that the current liquid level height is 30cm. Press “key 2” to increase and press “key 3” to decrease.<br>[[image:Ell2.png|300px]]

# After the current liquid level of the oil tank is put properly, press “key 1” more than 8 seconds to enter the automatic adjustment state of oil tank signal strength. <br>

# After the current liquid level of the oil tank is put properly, press “key 1” for more than 8 seconds to enter the automatic adjustment state of oil tank signal strength. <br>

## At the moment, you may observe whether the displayed height on the display screen is consistent with actual fuel level (for example, the predicted level is about 300mm and displayed 285.2mm).<br>

## At the moment, you may observe whether the displayed height on the display screen is consistent with the actual fuel level (for example, the predicted level is about 300mm and displayed 285.2mm).<br>

## If the display screen displays 000.0 or the displayed height is quite different from the actual condition, the probe may be moved slightly or grind the fuel tank wall more. In addition, the buzzer in the equipment sounds continuous (if the buzzer sounds on and off or does not sound, it needs to seek the installation point or grind the fuel tank wall more until the buzzer does not sound).<br>

## If the display screen displays 000.0 or the displayed height is quite different from the actual condition, the probe may be moved slightly or grind the fuel tank wall more. In addition, the buzzer in the equipment sounds continuous (if the buzzer sounds on and off or does not sound, it needs to seek the installation point or grind the fuel tank wall more until the buzzer does not sound).<br>

## Hold down “key 1" for more than 8 seconds to complete search and test of installation point.<br>

## Hold down “key 1" for more than 8 seconds to complete the search and test of installation point.<br>

[[Category:Accessories]]

[[Category:Accessories]]