Difference between revisions of "Upgrading CAN-CONTROL to CAN-CONTROl+Immobilizer"

From Wiki Knowledge Base | Teltonika GPS
(Created page with "Wiki. FAQ Upgrading CAN-CONTROL to CAN-CONTROl+Immobilizer Possible problems: 1. Doors Lock/Unlock is not working. 2. Doors Lock/Unlock works but engine blocking and unbloc...")
(6 intermediate revisions by 3 users not shown)
Line 1: Line 1:
−
== Struggle after upgrading CAN-CONTROL to CAN-CONTROL+Immobilizer? ==
+
Wiki.
−
Possible encounters after upgrading CAN bus adapter:
+
FAQ
  
−
* Vehicle doors Lock/Unlock is not working;
+
Upgrading CAN-CONTROL to CAN-CONTROl+Immobilizer
−
* Vehicle doors Lock/Unlock is working but engine Blocking/Unblocking does not and after sending commands, the response is: "''CAN-CONTROL cmd not supported''".
 
  
−
If You encounter with any of these issues - follow solution steps below.
+
Possible problems:
  
−
== Solution ==
+
1. Doors Lock/Unlock is not working.
−
After installation is completed and CAN bus adapter program is set, please, follow these steps:
+
2. Doors Lock/Unlock works but engine blocking and unblock does not. Most of times response will be: CMD not supported. In some situations engine block will work but unblocking will not.
  
−
# Do a learning procedure - using the vehicle key, unlock and lock vehicle '''three''' '''times''';
+
After installation is done and program number is set please do learning procedure.
−
# Send GPRS command - "  lvcansetprog 11120" (or any other). Program number must contain 5 digits.
 
−
# Send GPRS command - "  lvcansetprog ''the one that is for Your vehicle model''". Program number can be seen in at the top of the CAN adapter connection scheme.
 
−
# After receiving a response to a command, repeat the learning procedure (first step).
 
  
 +
1. send lvcansetprog 11120 (Or any other)
 +
2. send lvcansetprog (one that is for your car model)
 +
3. After you will receive response please do learning with key locking/unlocking 3 times. lock>unlock;lock>unlock;lock>unlock;
  
−
{|
+
Now you can try commands to open and close doors.
−
|-
+
Now you can try commands to block and unblock engine.
−
| [[File:Alert.png|left|link=]] || <b>'''Note''': Before SMS text, two space symbols should be inserted if no SMS username or password was set in [[FMB001 SMS/Call settings|SMS / Call settings]].
 
−
After completed these steps, commands to open/close and to block/unblock engine can be performed.
 
−
All SMS/GPRS responses should inform You that particular command has been completed successfully.</b>
 
−
|}
 
  
−
<bR>
+
All sms/gprs responces should inform you that command has been completed succesffully.
−
{|
+
 
−
|-
+
Note: If installing CAN-CONTROL adapter into different vehicle learning must be initiated. If adapter will be installed back on previous car model learning step must be repeated.
−
| [[File:Alert.png|left|link=]] || <b>'''Note''': if installing CAN-CONTROL adapter into different vehicle - program should be changed according to the vehicle model and learning must be initiated ("first solution step").  
 
−
If adapter will be installed again on the previous vehicle - program number needs to be restored and learning step must be repeated.
 
−
</b>
 
−
|}
 

Revision as of 17:12, 14 January 2021

Wiki. FAQ

Upgrading CAN-CONTROL to CAN-CONTROl+Immobilizer

Possible problems:

1. Doors Lock/Unlock is not working. 2. Doors Lock/Unlock works but engine blocking and unblock does not. Most of times response will be: CMD not supported. In some situations engine block will work but unblocking will not.

After installation is done and program number is set please do learning procedure.

1. send lvcansetprog 11120 (Or any other) 2. send lvcansetprog (one that is for your car model) 3. After you will receive response please do learning with key locking/unlocking 3 times. lock>unlock;lock>unlock;lock>unlock;

Now you can try commands to open and close doors. Now you can try commands to block and unblock engine.

All sms/gprs responces should inform you that command has been completed succesffully.

Note: If installing CAN-CONTROL adapter into different vehicle learning must be initiated. If adapter will be installed back on previous car model learning step must be repeated.

Retrieved from "https://wiki.teltonika-gps.com/index.php?title=Upgrading_CAN-CONTROL_to_CAN-CONTROl%2BImmobilizer&oldid=61938"