| Line 11: |
Line 11: |
| | {{{txt_can_speed|* '''CAN speed''' - If speed from BT OBDII dongle is higher than 0 km/h, Vehicle MOVING mode is used; If speed from BT OBDII dongle is equal 0 km/h, Vehicle on STOP mode is used;}}} | | {{{txt_can_speed|* '''CAN speed''' - If speed from BT OBDII dongle is higher than 0 km/h, Vehicle MOVING mode is used; If speed from BT OBDII dongle is equal 0 km/h, Vehicle on STOP mode is used;}}} |
| | If there is no GNSS fix, the accelerometer determines profile change. If there is no OBDII dongle active (or speed reported by dongle == 0 km/h) accelerometer determines profile change.<br></br> | | If there is no GNSS fix, the accelerometer determines profile change. If there is no OBDII dongle active (or speed reported by dongle == 0 km/h) accelerometer determines profile change.<br></br> |
| − | '''Note:''' From new firmware version '''03.25.14.Rev.03''' added new '''multiple movement sources selection''' at once. If any of selected movement sources are active, movement mode will be activated. If all selected sources are inactive STOP mode will be enabled. Configurable movement parameter ID has been changed. Information regarding configurable parameter ID could be found in the table below:
| + | }}} |
| − | <table class="nd-othertables_2" style="width: 68%;">
| |
| − | <tr>
| |
| − | <th style="width: 10%; text-align:left; vertical-align:middle; color:black">Firmware version until 03.25.14.rev.03</th>
| |
| − | <th style="width: 20%; text-align:center; vertical-align:middle; color:black">Firmware version from 03.25.14.rev.03</th>
| |
| − | </tr>
| |
| − | <tr>
| |
| − | <td style="width: 8%; text-align:center;">100 - Parameter ID</td>
| |
| − | <td style="width: 8%; text-align:center">138 - Parameter ID</td>
| |
| − | </tr>
| |
| − | </table>}}}
| |
| − | {{{speed_source|===Speed Source===
| |
| − | ------------------
| |
| − | [[Image:Speed.gif|right|300px]]
| |
| − | Speed source will be used to determine which speed source to use.<br></br>
| |
| − | '''Note:''' If the speed source is configured as OBD / CAN, the device will try to take speed from OBD first. If the speed value read is 0, then it tries to take speed from CAN. If the speed value is also 0, the firmware takes the speed from GNSS, even though it is not configured.}}}
| |
| | ===Records Saving/Sending Without TS=== | | ===Records Saving/Sending Without TS=== |
| | ------------------ | | ------------------ |
| Line 75: |
Line 60: |
| | * GPS + Galileo + BeiDou + IRNSS; | | * GPS + Galileo + BeiDou + IRNSS; |
| | * GPS + Galileo + GLONASS + BeiDou + IRNSS.}}} | | * GPS + Galileo + GLONASS + BeiDou + IRNSS.}}} |
| − | {{{battery_charge|===Battery Charge Mode===
| |
| | ------------------ | | ------------------ |
| − | In ''Battery Charge Mode'' settings user can choose when battery will be charged.<br>
| |
| − | [[Image:Battery_charge.gif|right|300px]]
| |
| − | Possible options:
| |
| − | * '''On Need''' - enable battery charger any time when needed;
| |
| − | * '''After Ignition ON''' - charger can be enabled after ignition is turned on, except if battery is fully charged or 10 minute timeout has not passed since device was turned on for faster FIX receiving;
| |
| − | * '''Always''' - enables charging all the time (even if any sleep mode is active).}}}
| |
| | {{{analog_input|===Analog Input Value Range=== | | {{{analog_input|===Analog Input Value Range=== |
| | ------------------ | | ------------------ |
