Template:FMX13A First start card withoutSD: Difference between revisions

Revision as of 11:54, 16 August 2022

How to insert Micro-SIM card and connect the battery

Gently remove FMM125 cover using plastic pry tool from both sides.
Note: To properly open a new case please watch this video.
Insert Micro-SIM card as shown with PIN request disabled or read Security info how to enter it later in Teltonika Configurator. Make sure that Micro-SIM card cut-off corner is pointing forward to slot.
Connect battery as shown to device. Position the battery in place where it does not obstruct other components.
After configuration, see “PC Connection (Windows)”, attach device cover back.

Micro-SIM card insertion/removal must be performed when device is powered off – external voltage and internal battery disconnected. Otherwise Micro-SIM card might be damaged or device will not detect it.

@@ Line 1: / Line 1: @@
-=='''How to insert {{{sim_type|Nano-}}}SIM card {{{battery|and connect the battery}}}'''==
+=='''How to insert {{{sim_type|Micro-}}}SIM card {{{battery|and connect the battery}}}'''==
 # Gently remove {{{model|FMM125}}} '''cover''' using '''plastic pry tool''' from both sides.<p><b>Note:</b> To properly open a new case please watch this [https://youtu.be/PBXVNXfRjg0 video].</p>
-# Insert '''{{{sim_type|Nano-}}}SIM''' card as shown with '''PIN request disabled''' or read '''[[{{{model|FMM125}}} Security info|Security info]]''' how to enter it later in [[Teltonika Configurator]]. Make sure that {{{sim_type|Nano-}}}SIM card '''cut-off corner''' is pointing forward to slot.
+# Insert '''{{{sim_type|Micro-}}}SIM''' card as shown with '''PIN request disabled''' or read '''[[{{{model|FMM125}}} Security info|Security info]]''' how to enter it later in [[Teltonika Configurator]]. Make sure that {{{sim_type|Micro-}}}SIM card '''cut-off corner''' is pointing forward to slot.
 {{{be_battery|# Connect '''battery''' as shown to device. Position the battery in place where it does not obstruct other components.
-# Using double sided tape, stick internal battery to the bottom part of the device case. Battery should be glued approximately 16 millimeters from the bottom wall of the case.
-#Connect battery to the PCB and gently place PCB into the bottom case.
-# Make sure to carefully align the PCB and insert it without bending or stressing the pin.
 # After '''configuration''', see “'''[[{{{model|FMM125}}}_First_Start#PC Connection (Windows)|PC Connection (Windows)]]'''”, attach device '''cover''' back.}}}
+[[Image:FMC13A_cover1_correct.png|280px]][[Image:FMC13A_cover2_correct.png|280px]][[Image:FMC13A_cover3_correct.png|280px]][[Image:FMC13A_cover4_correct.png|280px]]
-[[File:FMM13A device setup - 01.jpg|280px]]
-[[File:FMM13A device setup - 02.jpg|280px]]
-[[File:FMM13A device setup - 03.jpg|280px]]
-[[File:FMM13A device setup - 04.jpg|280px]]
-[[File:FMM13A device setup - 05.jpg|280px]]
-[[File:FMM13A device setup - 06.jpg|280px]]
 {|
 |-
-| [[File:Alert.png|left|link=]] || <b>{{{sim_type|Nano-}}}SIM card insertion/removal must be performed when device is powered off – external voltage {{{battery|and internal battery}}} disconnected. Otherwise {{{sim_type|Nano-}}}SIM card might be damaged or device will not detect it.</b>
+| [[File:Alert.png|left|link=]] || <b>{{{sim_type|Micro-}}}SIM card insertion/removal must be performed when device is powered off – external voltage {{{battery|and internal battery}}} disconnected. Otherwise {{{sim_type|Micro-}}}SIM card might be damaged or device will not detect it.</b>
 |}