Wiki Knowledge Base | Teltonika GPS

Changes

ADAS Camera Manual (view source)

Revision as of 10:03, 2 December 2022

2,512 bytes removed ,  10:03, 2 December 2022
→‎ADAS data transferring timing
Line 1: Line 1:  
__TOC__
 
__TOC__
−
== Main (front) camera unit preparation ==
  −
The main unit comes prepared for bus/large truck setup (cable routing) or vehicles with mostly vertical windshields''.'' To set up the unit for an average truck or passenger vehicle, dismantle partially as shown below:
  −
{| class="wikitable"
  −
|+
  −
! colspan="6" |Unit preparation
  −
|-
  −
|[[File:Camera1.jpg|center|frameless|181x181px]]
  −
|1.  Remove cover
  −
|[[File:Camera1.jpg|center|frameless|186x186px]]
  −
|2. Remove (2x) screws,
  −
remove plastic cover
  −
|[[File:Camera3.png|center|frameless|216x216px]]
  −
|3. Remove (2x) screws,
  −
pry plastic mounting
     −
frame off Unit from corners
+
== Product Specification ==
−
|-
+
<table class="nd-othertables" style="width: 68%;">
−
|[[File:Camera4.png|center|frameless|199x199px]]
+
        <th style="width: 10%; text-align:left; vertical-align:middle; color:black">Technical data</th>
−
|4. Reroute the main
+
        <th style="width: 20%; text-align:center; vertical-align:middle; color:black">Description</th>
−
cable (and rear camera
+
    </tr>
−
 
+
<tr>
−
cable, if adding) around unit
+
        <td style="width: 8%; text-align:left;">Supported by</td>
−
 
+
        <td style="width: 8%; text-align:left">FMB640, FMC640, FMB125, FMC125, FMB225, FMC225</td>
−
to front (glass side)
+
    </tr>
−
|[[File:Camera5.png|center|frameless|221x221px]]
+
<tr>
−
|5. Press tightly into
+
        <td style="width: 8%; text-align:left">Camera Resolution</td>
−
channels when routing cables.
+
        <td style="width: 8%; text-align:left">1280 x 720 (HD)</td>
−
 
+
    </tr>
−
Remove front camera dust sticker
+
<tr>
−
|[[File:Camera6.png|center|frameless|238x238px]]
+
        <td style="width: 8%; text-align:left">View angle</td>
−
|6. Replace 1 cover only
+
        <td style="width: 8%; text-align:left">30 (V), 52 (H), 60 (D)</td>
−
removed from step 3.
+
    </tr>
−
 
+
<tr>
−
Replace 2 screws.
+
        <td style="width: 8%; text-align:left">Size</td>
−
 
+
        <td style="width: 8%; text-align:left">80 x 120 x 50 mm</td>
−
Leave the remaining
+
    </tr>
−
 
+
<tr>
−
covers off until the last step
+
        <td style="width: 8%; text-align:left">SD card</td>
−
|}
+
        <td style="width: 8%; text-align:left">Max. 128GB</td>
−
 
+
    </tr>
−
==ADAS Calibration==
+
<tr>
−
ADAS Calibration requires:
+
        <td style="width: 8%; text-align:left">Video encoding</td>
−
 
+
        <td style="width: 8%; text-align:left">H264</td>
−
*a laptop with an internet connection and a browser
+
    </tr>
−
 
+
<tr>
−
*micro-USB cable
+
<table class="nd-othertables" style="width: 68%;">
−
 
+
        <th style="width: 10%; text-align:left; vertical-align:middle; color:black">Electrical parameters</th>
−
*tape measure
+
        <th style="width: 20%; text-align:center; vertical-align:middle; color:black">Description</th>
−
 
+
    </tr>
−
*parking the car with a clear, open stretch of about a 45 meters unobstructed view (try to park close to your facility to keep the internet connection accessible – at least during the calibration driver installation)
+
<tr>
−
*a partner to drive the vehicle while speed correction is performed
+
          <td style="width: 8%; text-align:left;">Input voltage range</td>
−
 
+
          <td style="width: 8%; text-align:left">9 – 36 V</td>
−
Before beginning, insert the provided micro-SD card into the main unit in the location shown below until it clicks and turn the Ignition ON. Wait for the prompt, then press and release the center button one time. After the successful prompt and the unit reboots, continue to step 1.
+
    </tr>
−
[[File:Vehinst12.png|center|frameless|335x335px]]
+
<tr>
−
 
+
          <td style="width: 8%; text-align:left">Temperature</td>
−
1. Park the vehicle in a spot with a clear stretch of unobstructed line-of-sight (about 45 meters). Leave the vehicle running
+
          <td style="width: 8%; text-align:left">-20 °C to +70 °C (operation)
−
2. Connect the USB cable to the Mirco-USB port on the side of the main unit (windshield) and the other end to the laptop. If on a windows 10 machine, it should automatically install the required driver. If not or on an older machine, go to movon.co.kr, go to the ‘ADAS’ tab at the top then to ‘Downloads’ under Support. Download the appropriate zip file (contains driver) and extract it fully for your version of Windows OS (if using the 7/8 driver, install the .exe file). If WIN10, once downloaded, disconnect/reconnect the USB and it should automatically install, or find the unit in Device Manager and right-click, Update Driver and browse for driver locally.[[File:Vehinst13.png|center|frameless|335x335px]]
+
-40 °C to +85 °C (storage)</td>
−
3. Open Chrome browser again and type in ''’10.0.0.1’'' into the URL bar''.'' If the driver was installed properly, the calibration screen will appear. Input credentials and press ''LOGIN''  USER:     ''admin''  PASS:     ''1234''<br>
+
    </tr>
−
4. '''Select Vehicle Signal Type:''' there are several wiring options for installation: CAN-BUS / Analog (GPIO) / GPS (Speed). Select the proper calibration option based off which was installed: CAN (if CAN file is available), Analog (if analog signals were tapped)
+
<tr>
−
 
+
          <td style="width: 8%; text-align:left">Relative Humidity</td>
−
'''''Vehicle Data File''''' (CAN-BUS)For CAN-BUS connection, choose the ‘Vehicle info file’ tab and select ‘Choose File’ to upload the previously downloaded ‘mdasinfo.dat’ file (see ‘CAN-Equipped vehicles’ section).
+
          <td style="width: 8%; text-align:left">Max. 90 %</td>
−
[[File:Vehinst14.jpg|center|frameless|363x363px]]
+
    </tr>
−
 
+
<tr>
−
==Camera location and Vehicle Measurement==
+
          <td style="width: 8%; text-align:left">Power consumption</td>
−
Camera location and vehicle measurement can affect ADAS performance. It`s very important put accurate data for the best performance.
+
          <td style="width: 8%; text-align:left">12V max @300mA
−
[[File:Vehinst15.png|center|frameless|404x404px|alt=]]
+
12V Idle state @ 3mA</td>
 +
    </tr>
 +
<tr><br>
 
<table class="nd-othertables" style="width: 68%;">
 
<table class="nd-othertables" style="width: 68%;">
−
           <th style="width: 10%; text-align:left; vertical-align:middle; color:black">Camera Option</th>
+
           <th style="width: 10%; text-align:left; vertical-align:middle; color:black">Interface</th>
 
           <th style="width: 20%; text-align:center; vertical-align:middle; color:black">Description</th>
 
           <th style="width: 20%; text-align:center; vertical-align:middle; color:black">Description</th>
 
     </tr>
 
     </tr>
 
<tr>
 
<tr>
−
           <td style="width: 8%; text-align:left;">Camera Height</td>
+
           <td style="width: 8%; text-align:left;">USB</td>
−
           <td style="width: 8%; text-align:left">Distance from  ground to the center of camera lens.</td>
+
           <td style="width: 8%; text-align:left">USB 2.0 (for calibration)</td>
 
     </tr>
 
     </tr>
 
<tr>
 
<tr>
−
           <td style="width: 8%; text-align:left">Camera Center</td>
+
           <td style="width: 8%; text-align:left">CAN</td>
−
           <td style="width: 8%; text-align:left">Distance from the  center of windshield to camera lens
+
           <td style="width: 8%; text-align:left">CAN 2.0 (Car signal – Left/Right, Speed, RPM, Brake)</td>
−
“-“: Left Side / “+”:Right Side
+
    </tr>
−
 
+
<tr><br>
−
(If ADAS is  attached 5cm to the right from the center, input 5.
+
          <td style="width: 8%; text-align:left">RS232</td>
−
 
+
          <td style="width: 8%; text-align:left">Indicator TX/RC (for communication with FM device)</td>
−
If ADAS is  attached 5cm to the left from the center, input -5.)  
  −
</td>
   
     </tr>
 
     </tr>
−
<tr>
+
</table>
−
          <td style="width: 8%; text-align:left">Camera to Wheel</td>
  −
          <td style="width: 8%; text-align:left">Distance from the  camera to the center of the wheel.
  −
'''For trucks or  buses''', some vehicles’  wheels are located behind.
     −
In this case,  please input 20cm.
+
== ADAS and FMC640 Features ==
−
</td>
+
[[File:MicrosoftTeams-image (12).png|left|frameless|52x52px]]
−
    </tr><tr><td>Vehicle Width</td><td>Distance between  the wheels.
+
'''Periodic photo sending'''
−
Measure distance  from left outside boarder to right outside boarder of the wheels.
  −
</td></tr><tr><td>Camera to bumper</td><td>Distance from the  camera lens to the end of the bumper.
  −
For trucks or  buses, it is recommended to input 300 if sensitive FCW warning is needed.
  −
</td></tr></table>
     −
Camera angle – adjust the camera angle to locate the horizontal between the red guide lines.
+
Possible to receive periodical photo from ADAS
−
[[File:Vehinst16.png|center|frameless|316x316px]]
  −
In case of indoor installation or somewhere you cannot see the horizon properly, use same data to "'''Camera Height'''”. Mark the same height on the wall apart about 3 ~ 5 meters from the vehicle.
  −
[[File:Vehinst17.png|center|frameless|332x332px]]
     −
Fine Camera Angle - For better accuracy of ADAS, locate the yellow dotted line in the horizon as close as possible.
+
[[File:MicrosoftTeams-image (13).png|left|frameless|52x52px]]
−
[[File:Vehinst18.png|center|frameless|344x344px]]
     −
Hood Line - Locate the red line at the end of the vehicle’s hood line to remove the useless area.
+
'''Video/photo by request'''
−
[[File:Vehinst19.png|center|frameless|360x360px]]
  −
Please follow link for video instruction: https://www.youtube.com/watch?v=93wrc6j9aqA
     −
==ADAS camera settings configuration==
+
You can request video/photo from ADAS
−
{| class="wikitable"
  −
| colspan="2" |'''You can adjust  the LDW Sensitivity for your convenience'''
  −
|-
  −
|
  −
* Enable LDW function. (On  / Off)
     −
* Set the Activation Speed  (15, 30, 45, 60, 75km/h).
+
== ADAS Features ==
−
* Set the sensitivity of  LDW warning on a scale of 1 to 5.
+
[[File:PEDESTRIAN COLLISION WARNING.png|left|frameless|52x52px]]
−
* As the level gets higher,  it gets more sensitive.
+
'''PCW''' '''(PEDESTRIAN COLLISION WARNING)'''
−
* Enable Repeat LDW (On /  Off)
  −
* If it’s on, ADAS keeps  warning until the driver secures the lane.
  −
* Warning sound: Select  preferred warning sound for LDW.
  −
|[[File:Mdconfi1.png|center|frameless]]
     −
|-
+
Notifies driver of any pedestrians, bicycles or motorcycles ahead.
−
| colspan="2" |'''You can adjust the FCW Sensitivity for your  convenience:'''
+
[[File:LANE DEPARTURE WARNING.png|left|frameless|52x52px]]
−
|-
+
'''LDW (LANE DEPARTURE WARNING)'''
−
|
  −
* Enable FCW function. (On  / Off)
  −
* Set the sensitivity of FCW warning on a scale of 1 to 5.
  −
(As the level  gets higher, it gets more sensitive)
  −
* Enable Repeat FCW (On /  Off).  
  −
(If it’s on, ADAS keeps warning until the driver secures safe distance)
  −
* Enable Sync with Brake  (On / Off).
  −
(If it’s on, ADAS won’t give FCW warning if the brake pedal was used)
  −
* Warning sound: Select  preferred warning sound for FCW
  −
|[[File:Mdconf2.png|center|frameless|301x301px]]
  −
|-
  −
| colspan="2" |'''Safety distance alert setup:'''
  −
|-
  −
|
  −
* Enable SDA function. (On  / Off)
  −
* Set the sensitivity of  SDA on a scale of 1 to 5.
  −
* As the level  gets higher, it gets more sensitive.
  −
* Repeat SDA and SDA  re-alert can be changed. (On / Off)
     −
- Repeat SDA: If it’s on, ADAS keeps warning until the driver secures safe distance.
+
Helps to regain direction if the driver unintentionally departs lanes.
 +
[[File:FORWARD COLLISION WARNING.png|left|frameless|52x52px]]
 +
'''FCW (FORWARD COLLISION WARNING)'''
 +
[[File:FORWARD PROXIMITY WARNING.png|left|frameless|52x52px]]
 +
Sends warning alerts if a crash is imminent to assist driver in maintaining a safe traveling distance.
   −
''- Re-alert  SDA: If it’s on, ADAS gives warnings every time''
+
'''FPW (FORWARD PROXIMITY WARNING)'''
   −
''the same front vehicle gets  closer than safe distance.''
+
Notifies driver if the vehicle moves forward while another vehicle is in the detection range, which can be setup at 1 m, 2 m, 3 meters.
−
|[[File:Mdconfi3.png|center|frameless]]
+
[[File:FRONT VEHICLE START ALARM.png|left|frameless|52x52px]]
−
|-
+
'''FVSA (FRONT VEHICLE START ALARM)'''
−
| colspan="2" |'''Pedestrian collision warning setup:'''
  −
|-
  −
|
  −
* Enable PCW function. (On  / Off)
     −
* Warning sound: Select  preferred warning sound for PCW.  
+
Notifies driver if the front vehicle started moving forward from 0 speed without the vehicle moving within 2 secs.
−
|[[File:Mdconfi4.png|center|frameless]]
+
[[File:SAFETYDISTANCEALERT.png|left|frameless|52x52px]]
−
|-
+
'''SDA (SAFETY DISTANCE ALERT)'''
−
| colspan="2" |'''Advanced ADAS setup:'''
  −
|-
  −
|
  −
* Enable Forward Proximity  Warning function. (On / Off)
  −
* Set the warning range on  a scale of 1 to 3.
  −
(As the level  gets higher, it gets more sensitive)
  −
* Enable Front vehicle  start alarm. (On / Off)
  −
* Enable Speed Limit  Recognition. (On / Off)
  −
* Set the warning  sensitivity (0, 5, 10, 15, 20%).
  −
Ex) If you  set 10% then you will get alarm
     −
when your speed over the limit more than 10%, 
+
Attracts the driver's attention to keep the safe distance ahead by warning the driver (active from 30km/h).
 +
[[File:DIGITAL VIDEO RECORDER.png|left|frameless|52x52px]]
 +
'''DVR (DIGITAL VIDEO RECORDER)'''
   −
100km limit -> Warning start from 110km speed.
+
Records scenes as HD+HD resolutions into SD card before and after an accident. (Every minute in a loop)
−
* Enable voice guidance (On  / Off).
+
[[File:SPEED LIMIT RECOGNITION.png|left|frameless|52x52px]]
−
|[[File:Mdconfi5.1.png|center|frameless]]
+
'''SLR (SPEED LIMIT RECOGNITION)'''
−
|-
  −
| colspan="2" |'''Fleet management setup'''
  −
|-
  −
|
  −
* Set  Speed limit warning (Off, 80, 90, 100, 110, 120, 130, 140km/h).
     −
- You  can set your own speed limit for your fleet.
+
Recognizes speed limit signs and provides warnings for over speed (Available with ADAS Plus).
−
 
  −
- You can set speed limit of your vehicle and  get warning if you over the speed limit.
  −
 
  −
* Enable  Transmit data RS-232 feature
  −
(Converter mode should be selected to work with FMx125).
  −
 
  −
It allows ADAS event data transmission to integrated device.
  −
* Set Lock  volume button control on a scale of 1 to 5 and Off.
  −
You can fix the volume level and prevent the driver from adjusting the
  −
 
  −
settings using indicator.
  −
* Set Break  time alarm on a scale of 1 to 6 hours and Off.
  −
 
  −
* Enable  Vibration setting for LDW, FCW, PCW (On / Off / Both).
  −
You can check the connection with the button.
  −
|[[File:Mdconfi6.1.png|center|frameless]]
  −
|-
  −
| colspan="2" |'''Miscellaneous  Settings:'''
  −
|-
  −
|
  −
* Speed Unit on Analog  video output (km/h or MPH).
  −
 
  −
* Set Video out format  (NTSC / PAL).
  −
 
  −
* Set Voice guide language
  −
(English /  Korean / Chinese / Spanish / Japanese / Hebrew/ No Sound).
  −
* Enable Indicator buzzer  (On / Off).  
  −
 
  −
* Speed Display on  Indicator could be ON/Off
  −
|[[File:Mdconfi7.png|center|frameless]]
  −
|-
  −
| colspan="2" |'''ADAS Setup Complete'''
  −
|-
  −
|
  −
* Click “Complete” button  to finish Calibration setup. Then ADAS will be
  −
rebooted automatically.
  −
* Click “Export vehicle  profile” button, if you want to download vehicleprofile.dat.
  −
 
  −
This vehicleprofile contains all the calibration  settings you’ve set.
  −
 
  −
With this file, you can simply apply current settings to  another vehicle.
  −
|[[File:Mdconfi8.png|frameless|alt=|center|351x351px]]
  −
|}
      
==ADAS data transferring timing==
 
==ADAS data transferring timing==
 +
'''Test was performed using Baudrate 460800'''
 
{| class="wikitable"
 
{| class="wikitable"
 
! rowspan="1" style="width: 400px; background: #0054A6; color: white;" |'''Image resolution'''
 
! rowspan="1" style="width: 400px; background: #0054A6; color: white;" |'''Image resolution'''
Line 242: Line 133:  
|-
 
|-
 
|style="text-align: center;|640x480
 
|style="text-align: center;|640x480
−
|style="text-align: center;|30
+
|style="text-align: center;|0
 
|<nowiki>-</nowiki>
 
|<nowiki>-</nowiki>
−
|style="text-align: center;|~24kB
+
|style="text-align: center;|~10kB
 
|style="text-align: center;| -
 
|style="text-align: center;| -
−
|style="text-align: center;|72s / 100s
+
|style="text-align: center;|48s / 70s
 
|style="text-align: center; style=" width: 150px; background: white; color: black;" |[[File:640x4801.jpg|thumb]]
 
|style="text-align: center; style=" width: 150px; background: white; color: black;" |[[File:640x4801.jpg|thumb]]
 
|-
 
|-
 
|style="text-align: center;|1280x720
 
|style="text-align: center;|1280x720
−
|style="text-align: center;|30
+
|style="text-align: center;|0
 
|<nowiki>-</nowiki>
 
|<nowiki>-</nowiki>
−
|style="text-align: center;|~160kB
+
|style="text-align: center;|~28kB
 
|style="text-align: center;| -
 
|style="text-align: center;| -
−
|style="text-align: center;|180s / 230s
+
|style="text-align: center;|67s / 103s
 
|style="text-align: center; style=" width: 150px; background: white; color: black;" |[[File:1280x7201.jpg|thumb]]
 
|style="text-align: center; style=" width: 150px; background: white; color: black;" |[[File:1280x7201.jpg|thumb]]
 
|-
 
|-
Line 260: Line 151:  
|-
 
|-
 
|style="text-align: center;|640x480
 
|style="text-align: center;|640x480
 +
|style="text-align: center;| 0
 +
|style="text-align: center;|10s
 
|style="text-align: center;| -
 
|style="text-align: center;| -
−
|style="text-align: center;|5s
+
|style="text-align: center;|~144kB
 +
|style="text-align: center;|86s / 198s
 +
|
 +
|-
 +
|style="text-align: center;|640x480
 +
|style="text-align: center;| 25
 +
|style="text-align: center;|10s
 
|style="text-align: center;| -
 
|style="text-align: center;| -
−
|style="text-align: center;|~588kB
+
|style="text-align: center;|~140kB
−
|style="text-align: center;|75s / 110s
+
|style="text-align: center;|58s / 144s
 
|
 
|
 
|-
 
|-
 
|style="text-align: center;|640x480
 
|style="text-align: center;|640x480
 +
|style="text-align: center;| 50
 +
|style="text-align: center;|10s
 
|style="text-align: center;| -
 
|style="text-align: center;| -
−
|style="text-align: center;|10s
+
|style="text-align: center;|~139kB
 +
|style="text-align: center;|48s / 110s
 +
|
 +
|-
 +
|style="text-align: center;|640x480
 +
|style="text-align: center;| 0
 +
|style="text-align: center;|20s
 +
|style="text-align: center;| -
 +
|style="text-align: center;|~285 kb
 +
|style="text-align: center;|183s / 400s
 +
|
 +
|-
 +
|style="text-align: center;|640x480
 +
|style="text-align: center;| 25
 +
|style="text-align: center;|20s
 +
|style="text-align: center;| -
 +
|style="text-align: center;|~201 kb
 +
|style="text-align: center;|155s / 349s
 +
|
 +
|-
 +
|style="text-align: center;|640x480
 +
|style="text-align: center;| 50
 +
|style="text-align: center;|20s
 +
|style="text-align: center;| -
 +
|style="text-align: center;|~150 kb
 +
|style="text-align: center;|145s / 400s
 +
|
 +
|-
 +
|style="text-align: center;|640x480
 +
|style="text-align: center;| 0
 +
|style="text-align: center;|30s
 
|style="text-align: center;| -
 
|style="text-align: center;| -
−
|style="text-align: center;|~1MB
+
|style="text-align: center;|~439 kb
−
|style="text-align: center;|201s / 290s
+
|style="text-align: center;|201s / 501s
 
|
 
|
 
|-
 
|-
 
|style="text-align: center;|640x480
 
|style="text-align: center;|640x480
 +
|style="text-align: center;| 25
 +
|style="text-align: center;|30s
 
|style="text-align: center;| -
 
|style="text-align: center;| -
−
|style="text-align: center;|15s
+
|style="text-align: center;|~390 kb
 +
|style="text-align: center;|185s / 3558s
 +
|
 +
|-
 +
|style="text-align: center;|640x480
 +
|style="text-align: center;| 50
 +
|style="text-align: center;|30s
 
|style="text-align: center;| -
 
|style="text-align: center;| -
−
|style="text-align: center;|~1.5MB
+
|style="text-align: center;|~239 kb
−
|style="text-align: center;|220s / 310s
+
|style="text-align: center;|180s / 550s
 
|
 
|
 
|-
 
|-
 
|style="text-align: center;|1280x720
 
|style="text-align: center;|1280x720
 +
|style="text-align: center;| 0
 +
|style="text-align: center;|10s
 
|style="text-align: center;| -
 
|style="text-align: center;| -
−
|style="text-align: center;|5s
+
|style="text-align: center;|~286KB
 +
|style="text-align: center;|90s / 261s
 +
|-
 +
|style="text-align: center;|1280x720
 +
|style="text-align: center;| 25
 +
|style="text-align: center;|10s
 
|style="text-align: center;| -
 
|style="text-align: center;| -
−
|style="text-align: center;|~875KB
+
|style="text-align: center;|~260KB
−
|style="text-align: center;|221s / 310s
+
|style="text-align: center;|78s / 215s
 
|style="text-align: center;|[[File:481012 Adas apkirptas 2.mp4]]
 
|style="text-align: center;|[[File:481012 Adas apkirptas 2.mp4]]
 +
|
 +
|-
 +
|style="text-align: center;|1280x720
 +
|style="text-align: center;| 50
 +
|style="text-align: center;|10s
 +
|style="text-align: center;| -
 +
|style="text-align: center;|~235KB
 +
|style="text-align: center;|70s / 211s
 +
|
 
|-
 
|-
 
|style="text-align: center;|1280x720
 
|style="text-align: center;|1280x720
 +
|style="text-align: center;| 0
 +
|style="text-align: center;|20s
 
|style="text-align: center;| -
 
|style="text-align: center;| -
−
|style="text-align: center;|10s
+
|style="text-align: center;|~590 kb
 +
|style="text-align: center;|120s / 502s
 +
|
 +
|-
 +
|style="text-align: center;|1280x720
 +
|style="text-align: center;| 25
 +
|style="text-align: center;|20s
 
|style="text-align: center;| -
 
|style="text-align: center;| -
−
|style="text-align: center;|~1.64MB
+
|style="text-align: center;|~494KB
−
|style="text-align: center;|309s / 410s
+
|style="text-align: center;|111s / 430s
 
|
 
|
 
|-
 
|-
 
|style="text-align: center;|1280x720
 
|style="text-align: center;|1280x720
 +
|style="text-align: center;| 50
 +
|style="text-align: center;|20s
 
|style="text-align: center;| -
 
|style="text-align: center;| -
−
|style="text-align: center;|15s
+
|style="text-align: center;|~460KB
 +
|style="text-align: center;|100s / 297s
 +
|
 +
|-
 +
|style="text-align: center;|1280x720
 +
|style="text-align: center;| 0
 +
|style="text-align: center;|30s
 
|style="text-align: center;| -
 
|style="text-align: center;| -
−
|style="text-align: center;|~2.52MB
+
|style="text-align: center;|~1MB
−
|style="text-align: center;|450s / 600s
+
|style="text-align: center;|241s / 710s
 
|
 
|
 
|-
 
|-
 +
|style="text-align: center;|1280x720
 +
|style="text-align: center;| 25
 +
|style="text-align: center;|30s
 +
|style="text-align: center;| -
 +
|style="text-align: center;|~720KB
 +
|style="text-align: center;|163s / 540s
 +
|
 +
|-
 +
|style="text-align: center;|1280x720
 +
|style="text-align: center;| 50
 +
|style="text-align: center;|30s
 +
|style="text-align: center;| -
 +
|style="text-align: center;|~695KB
 +
|style="text-align: center;|160s / 512s
 +
|
 
|}
 
|}
 
'''* NOTE:''' This approximate time which we receive during testing in real cases can be different.
 
'''* NOTE:''' This approximate time which we receive during testing in real cases can be different.
    
'''* NOTE''' Image compression is a type of data compression applied to digital images, to reduce their cost for storage or transmission. Algorithms may take advantage of visual perception and the statistical properties of image data to provide superior results compared with generic data compression methods which are used for other digital data.
 
'''* NOTE''' Image compression is a type of data compression applied to digital images, to reduce their cost for storage or transmission. Algorithms may take advantage of visual perception and the statistical properties of image data to provide superior results compared with generic data compression methods which are used for other digital data.
 +
[[Category: Teltonika ADAS]]
Retrieved from "https://wiki.teltonika-gps.com/view/Special:MobileDiff/75695...78235"