Difference between revisions of "Template:FMX640 Thermograph"

From Wiki Knowledge Base | Teltonika GPS
(11 intermediate revisions by 2 users not shown)
Line 1: Line 1:
 
==Introduction==
 
==Introduction==
−
With an increasing demand for cold-chain supply chains, Teltonika is offering the ability to monitor real-time information from freezer trailer thermographs. Each thermograph has an RS232 communication line where {{{model|}}} devices can connect via COM1/COM2 port of the device. The solution is easy to install and configure. This allows you to monitor the main information of the freezer trailer such as Temperature, Fridge door status, Alarms, etc., and generate events according to your needs. For more information please refer to the installation manual below.
+
Withsss an increasing demand for cold-chain supply chains, Teltonika is offering the ability to monitor real-time information from freezer trailer thermographs. Each thermograph has an RS232 communication line where {{{model|}}} devices can connect via COM1/COM2 port of the device. The solution is easy to install and configure. This allows you to monitor the main information of the freezer trailer such as Temperature, Fridge door status, Alarms, etc., and generate events according to your needs. For more information please refer to the installation manual below.
  
 
'''NOTE:''' this feature is available from FW ver. '''01.02.23.Rev.00'''
 
'''NOTE:''' this feature is available from FW ver. '''01.02.23.Rev.00'''
Line 8: Line 8:
 
{{{model|}}} can be connected to Euroscan, DataCold600, Transcan2, TouchPrint thermographs.
 
{{{model|}}} can be connected to Euroscan, DataCold600, Transcan2, TouchPrint thermographs.
  
−
Refer to the table below to see which freezers use which thermograph:
+
Refer to the table bellow to see which freezers use which thermograph:
 
{| class="wikitable"  
 
{| class="wikitable"  
 
|-
 
|-
Line 47: Line 47:
 
[[File:517441 TOUCHPRINT PINOUT.jpg]]
 
[[File:517441 TOUCHPRINT PINOUT.jpg]]
 
<br></br>
 
<br></br>
−
No configuration is necessary.
 
−
 
−
If the equipment does not receive information from the thermographer, the speed of the port accessing the configuration menu:
 
−
 
−
Keep the blue and red buttons pressed at the same time. "Enter PIN code" is displayed on the screen, enter pin "1111" by pressing the blue button four times. Travel for the options with the red button.
 
−
 
−
The ENG Display> OFF option must be ON, change its value with the keys ◄ and ►. Once switched to ON, keep scrolling through the options until you find Baud Rate> 9600. The value should be 9600, otherwise, adjust the speed by moving the cursor with the ◄ and ► keys, and adjust the speed with the keys ▲ and ▼.
 
−
 
 
<br></br>
 
<br></br>
 
'''TouchLog pinout''':
 
'''TouchLog pinout''':
Line 61: Line 53:
 
<br></br>
 
<br></br>
 
<br></br>
 
<br></br>
 +
No configuration is necessary.
  
 +
If the equipment does not receive information from the thermographer, the speed of the port accessing the configuration menu:
 +
 +
Keep the blue and red buttons pressed at the same time. "Enter PIN code" is displayed in screen, enter pin "1111" by pressing the blue button four times. Travel for the options with the red button.
 +
 +
The ENG Display> OFF option must be ON, change its value with the keys ◄ and ►. Once switched to ON, keep scrolling through the options until find Baud Rate> 9600. The value should be 9600, otherwise adjust the speed by moving the cursor with the ◄ and ► keys, and adjust speed with the keys ▲ and ▼.
  
 
AVL IDs for Touchprint:
 
AVL IDs for Touchprint:
Line 93: Line 91:
 
See ThermoKing Configuration.
 
See ThermoKing Configuration.
  
−
==='''Carrier Datacold 600'''===
+
==='''Carrier Datacold 600 / EuroScan'''===
 
To properly use DataCold 600 with FMX640 these steps must be followed:
 
To properly use DataCold 600 with FMX640 these steps must be followed:
 
*In FMX640 RS232 settings '''DataCold mode''' is selected and '''Baudrate set to 38400'''
 
*In FMX640 RS232 settings '''DataCold mode''' is selected and '''Baudrate set to 38400'''
Line 115: Line 113:
 
<br></br>
 
<br></br>
 
Available parameters (AVL IDs) with DataCold 600:
 
Available parameters (AVL IDs) with DataCold 600:
 +
 
{| class="wikitable" style="font-weight:bold; text-align:center;"
 
{| class="wikitable" style="font-weight:bold; text-align:center;"
 
|-
 
|-
 
! style="vertical-align:middle;" | Parameter name
 
! style="vertical-align:middle;" | Parameter name
−
! style="vertical-align:middle;" | Zone 1 Compartment state
+
! style="vertical-align:middle;" | Power mode
−
! style="vertical-align:middle;" | Zone 1 Compartment mode
 
−
! style="vertical-align:middle;" | Zone 1 Return Air Sensor
 
−
! style="vertical-align:middle;" | Zone 1 Supply Air Sensor
 
−
! style="vertical-align:middle;" | Zone 1 Set Temperature
 
−
! style="vertical-align:middle;" | Zone 1 Evaporator temperature
 
−
! style="vertical-align:middle;" | Zone 2 Return Air Sensor
 
−
! style="vertical-align:middle;" | Zone 2 Supply Air Sensor
 
−
! style="vertical-align:middle;" | Zone 2 Set Temperature
 
−
! style="vertical-align:middle;" | Zone 3 Compartment state
 
−
! style="vertical-align:middle;" | Zone 3 Compartment mode
 
−
! style="vertical-align:middle;" | Zone 3 Set Temperature
 
−
|-
 
−
| AVL ID
 
−
| 10045
 
−
| 10046
 
−
| 10047
 
−
| 10048
 
−
| 10049
 
−
| 10050
 
−
| 10056
 
−
| 10057
 
−
| 10058
 
−
| 10063
 
−
| 10064
 
−
| 10067
 
−
|}
 
−
{| class="wikitable" style="font-weight:bold; text-align:center;"
 
−
|-
 
−
! style="vertical-align:middle;" | Parameter name
 
 
! style="vertical-align:middle;" | Speed mode
 
! style="vertical-align:middle;" | Speed mode
 
! style="vertical-align:middle;" | Ambient Air Temperature
 
! style="vertical-align:middle;" | Ambient Air Temperature
−
! style="vertical-align:middle;" | Compressor Config
+
! style="vertical-align:middle;" | Alarm level
−
! style="vertical-align:middle;" | Installation Serial
+
! style="vertical-align:middle;" | Communication state flags
−
! style="vertical-align:middle;" | Analog Input 1-3
 
 
! style="vertical-align:middle;" | Manufacturer ID
 
! style="vertical-align:middle;" | Manufacturer ID
 
! style="vertical-align:middle;" | Battery State Flags
 
! style="vertical-align:middle;" | Battery State Flags
 
! style="vertical-align:middle;" | Fuel state flags
 
! style="vertical-align:middle;" | Fuel state flags
−
! style="vertical-align:middle;" | Maintenance 1-5 Hours
 
 
! style="vertical-align:middle;" | Run Mode
 
! style="vertical-align:middle;" | Run Mode
−
! style="vertical-align:middle;" | Error Codes
+
! style="vertical-align:middle;" | Fridge Error Codes
−
! style="vertical-align:middle;" | Temperature Probe 1-6
+
! style="vertical-align:middle;" | Fridge Temperature Probe 1-6
−
|-
+
! External Digital Sensor 1-4
−
| AVL ID
+
! External Analog Input 1-4
−
| 10071
+
|- style="font-weight:normal;"
−
| 10350
+
| style="vertical-align:middle; font-weight:bold;" | AVL ID
−
| 10353
+
| style="vertical-align:middle;" | 10062
−
| 10356
+
| style="vertical-align:middle;" | 10071
−
| 10468-10470
+
| style="vertical-align:middle;" | 10350
−
| 10472
+
| style="vertical-align:middle;" | 10352
−
| 10473
+
| style="vertical-align:middle;" | 10354
−
| 10474
+
| style="vertical-align:middle;" | 10472
−
| 10475-10479
+
| style="vertical-align:middle;" | 10473
−
| 10480
+
| style="vertical-align:middle;" | 10474
−
| 10639
+
| style="vertical-align:middle;" | 10480
−
| 10644-10649
+
| style="vertical-align:middle;" | 10639
 +
| style="vertical-align:middle;" | 10644-10649
 +
| 10464-10467
 +
| 10468-10471
 
|}
 
|}
−
 
 
<br></br>
 
<br></br>
 
Run mode explanation:
 
Run mode explanation:
Line 208: Line 178:
 
| 3
 
| 3
 
|}
 
|}
 +
  
 
==='''Euroscan'''===
 
==='''Euroscan'''===
 
To properly use Euroscan with FMX640 these steps must be followed:
 
To properly use Euroscan with FMX640 these steps must be followed:
 
*In FMX640 RS232 settings '''Euroscan mode''' is selected and '''Baudrate set to 38400'''
 
*In FMX640 RS232 settings '''Euroscan mode''' is selected and '''Baudrate set to 38400'''
−
*'''Partner mode enabled''' on Euroscan  
+
*'''Partner mode enabled''' on Euroscan 600
 
<br></br>
 
<br></br>
  
Line 268: Line 239:
 
[[File:ReeferIO.png]]
 
[[File:ReeferIO.png]]
 
<br></br>
 
<br></br>
−
Data sending parameters (AVL ID) used for "DataCold Reefer" are these: 10040 - 10649. For more in-depth information, please refer to '''[[{{{model|}}}_Teltonika_Data_Sending_Parameters_ID#Reefer_IO|Reefer IO data sending parameters]].'''
+
Data sending parameters (AVL ID) used for "DataCold Reefer" are these: 10040 - 10649. For more in-depth information, please refer to '''[[{{{model|}}}_Teltonika_Data_Sending_Parameters_ID#Reefer_IO]].'''
  
 
==== TK Transcan2 Reefer ====
 
==== TK Transcan2 Reefer ====
Line 275: Line 246:
 
<br></br>
 
<br></br>
 
Data sending parameters (AVL ID) used for "Transcan2  
 
Data sending parameters (AVL ID) used for "Transcan2  
−
" are these: 10683 - 10694. For more in-depth information, please refer to '''[[{{{model|}}}_Teltonika_Data_Sending_Parameters_ID#TK_Transcan_IO|Transcan IO data sending parameters]]'''
+
" are these: 10683 - 10694. For more in-depth information, please refer to '''[[{{{model|}}}_Teltonika_Data_Sending_Parameters_ID#TK_Transcan_IO.'''
  
 
==== Euroscan IO====
 
==== Euroscan IO====
Line 281: Line 252:
 
[[File:EuroScanIO.png]]
 
[[File:EuroScanIO.png]]
 
<br></br>
 
<br></br>
−
Data sending parameters (AVL ID) used for "Euroscan" are these: 484-489 and 10464-10467. For more in-depth information, please refer to '''[[{{{model|}}}_Teltonika_Data_Sending_Parameters_ID#TK_Euroscan_IO|Euroscan IO data sending parameters]].'''
+
Data sending parameters (AVL ID) used for "Euroscan" are these: 484-489 and 10464-10467. For more in-depth information, please refer to '''[[{{{model|}}}_Teltonika_Data_Sending_Parameters_ID#TK_Euroscan_IO]].'''
  
 
==== TK Touchprint/Touchlog I/O ====
 
==== TK Touchprint/Touchlog I/O ====
Line 288: Line 259:
 
[[File:TouchprintIO.png]]
 
[[File:TouchprintIO.png]]
 
<br></br>
 
<br></br>
−
Data sending parameters (AVL ID) used for "Touchprint Reefer" are these: 10695 - 10703. For more in-depth information, please refer to '''[[{{{model|}}}_Teltonika_Data_Sending_Parameters_ID#TK_Touchprint_IO|Touchprint IO data sending parameters]].'''
+
Data sending parameters (AVL ID) used for "Touchprint Reefer" are these: 10695 - 10703. For more in-depth information, please refer to '''[[{{{model|}}}_Teltonika_Data_Sending_Parameters_ID#TK_Touchprint_IO]].'''
  
  
 
[[Codec#Codec_8_Extended |Codec 8 Extended]] should be selected as the main data protocol in the “Protocol Settings” tab, which is located in the “System” section.
 
[[Codec#Codec_8_Extended |Codec 8 Extended]] should be selected as the main data protocol in the “Protocol Settings” tab, which is located in the “System” section.
  
 +
[[Category:{{{model|}}}]]
 
[[Category:{{{model|}}} Manual]]
 
[[Category:{{{model|}}} Manual]]

Revision as of 13:40, 12 January 2023

Manual > Template:FMX640 Thermograph

Introduction

Withsss an increasing demand for cold-chain supply chains, Teltonika is offering the ability to monitor real-time information from freezer trailer thermographs. Each thermograph has an RS232 communication line where devices can connect via COM1/COM2 port of the device. The solution is easy to install and configure. This allows you to monitor the main information of the freezer trailer such as Temperature, Fridge door status, Alarms, etc., and generate events according to your needs. For more information please refer to the installation manual below.

NOTE: this feature is available from FW ver. 01.02.23.Rev.00

Supported Thermographs

can be connected to Euroscan, DataCold600, Transcan2, TouchPrint thermographs.

Refer to the table bellow to see which freezers use which thermograph:

Thermograph Type
Freezer Type Euroscan DataCold600 Transcan2 TouchPrint/TouchLog
Carrier + + - -
ThermoKing +
 - + +

RS-232 Interface

RS-232 supports full-duplex communication which means the data can be both sent and received at the same time as they use separate transmission lines. Most of the modes are the same as for [[]]. When entering Sleep or Deep sleep RS-232 will be powered off. [[]] RS-232 connection diagram is shown in the figure below:

FMX640 and RS232 illustration v1.2.png

Installation guide

TouchPrint/TouchLog

506581 Thermograph Touchprint.png

TouchPrint pinout:

517441 TOUCHPRINT PINOUT.jpg



TouchLog pinout:

517635 TOUCHPLOG PINOUT V1.1.jpg



No configuration is necessary.

If the equipment does not receive information from the thermographer, the speed of the port accessing the configuration menu:

Keep the blue and red buttons pressed at the same time. "Enter PIN code" is displayed in screen, enter pin "1111" by pressing the blue button four times. Travel for the options with the red button.

The ENG Display> OFF option must be ON, change its value with the keys ◄ and ►. Once switched to ON, keep scrolling through the options until find Baud Rate> 9600. The value should be 9600, otherwise adjust the speed by moving the cursor with the ◄ and ► keys, and adjust speed with the keys ▲ and ▼.

AVL IDs for Touchprint:

Parameter name Input 1 Input 2 Input 3 Input 4 Input 5 Input 6 Setpoint 1 Setpoint 2 Setpoint 3
AVL ID 10695 10696 10697 10698 10699 10700 10701 10702 10703

Configuration: No configuration is necessary.

See ThermoKing Configuration.

Carrier Datacold 600 / EuroScan

To properly use DataCold 600 with FMX640 these steps must be followed:

  • In FMX640 RS232 settings DataCold mode is selected and Baudrate set to 38400
  • Partner mode enabled on DataCold 600



511336 Thermograph data cold colour .png


To enable Partner mode on DataCold 600:

  1. Press and hold the green button for 4 seconds
  2. Insert password. Default password - 1111
  3. Press the blue button to open 11 communication settings
  4. Press the green button to select edit action
  5. 11.1.0 Com1 Port settings should be opened, then press the green button again
  6. Then search for Partner protocol and press the green button to accept changes



Important note - RX and TX are inverted via the RS-232 connection. Scheme to properly manage DataCold 600 RS232 connection: Pinout of DataCold600 517440 DataCold PINOUT.jpg

Available parameters (AVL IDs) with DataCold 600:

Parameter name Power mode Speed mode Ambient Air Temperature Alarm level Communication state flags Manufacturer ID Battery State Flags Fuel state flags Run Mode Fridge Error Codes Fridge Temperature Probe 1-6 External Digital Sensor 1-4 External Analog Input 1-4
AVL ID 10062 10071 10350 10352 10354 10472 10473 10474 10480 10639 10644-10649 10464-10467 10468-10471



Run mode explanation:

Run mode StartStop Continious CycleCentry Unknown/Now available
Value (HEX) 0 1 2 7



Fuel and Battery state flag explanation:

Fuel/Battery Flag Status Available Error Alarm Digital sensor
Enum (bit field) value 0 1 2 3


Euroscan

To properly use Euroscan with FMX640 these steps must be followed:

  • In FMX640 RS232 settings Euroscan mode is selected and Baudrate set to 38400
  • Partner mode enabled on Euroscan 600



511336 Thermograph data cold colour .png


To enable Partner mode on Euroscan :

  1. Press and hold the green button for 4 seconds
  2. Insert password. Default password - 1111
  3. Press the blue button to open 11 communication settings
  4. Press the green button to select edit action
  5. 11.1.0 Com1 Port settings should be opened, then press the green button again
  6. Then search for Partner protocol and press the green button to accept changes



Important note - RX and TX are inverted via the RS-232 connection. Scheme to properly manage Euroscan RS232 connection: Pinout of DataCold600 517440 DataCold PINOUT.jpg

Available parameters (AVL IDs) with Euroscan :


External Sensor Temperature 1 External Sensor Temperature 2 External Sensor Temperature 3 External Sensor Temperature 4 External Sensor Temperature 5 External Sensor Temperature 6 Digital Sensor 1 Digital Sensor 2 Digital Sensor 3 Digital Sensor 4
484 485 486 487 488 489 10464 10465 10466 10467

Configuration

Make sure the device is configured to receive data from “Transcan2 Reefer”, "Touchprint Reefer", "Euroscan: or "DataCold Reefer". To do this, enter the configurator window, select the RS232 \ RS485 section displayed in the screenshots below, and configure accordingly (COM1/COM2 Settings, Mode “Transcan2 Reefer”, "Touchprint Reefer", "Euroscan"or "DataCold Reefer", Baudrate: Default)

RS-232 refer.png

DataCold Reefer

To configure "DataCold Reefer" I/O parameters, please select "Reefer IO": ReeferIO.png

Data sending parameters (AVL ID) used for "DataCold Reefer" are these: 10040 - 10649. For more in-depth information, please refer to _Teltonika_Data_Sending_Parameters_ID#Reefer_IO.

TK Transcan2 Reefer

To configure "Transcan2 Reefer" I/O parameters, please select "TK Transcom IO": TranscanIO.png

Data sending parameters (AVL ID) used for "Transcan2 " are these: 10683 - 10694. For more in-depth information, please refer to [[_Teltonika_Data_Sending_Parameters_ID#TK_Transcan_IO.

Euroscan IO

To configure "Euroscan refeer" I/O parameters select "Euroscan IO": EuroScanIO.png

Data sending parameters (AVL ID) used for "Euroscan" are these: 484-489 and 10464-10467. For more in-depth information, please refer to _Teltonika_Data_Sending_Parameters_ID#TK_Euroscan_IO.

TK Touchprint/Touchlog I/O

To configure "Touchprint Reefer" I/O parameters select "TK Touchprint IO":

TouchprintIO.png

Data sending parameters (AVL ID) used for "Touchprint Reefer" are these: 10695 - 10703. For more in-depth information, please refer to _Teltonika_Data_Sending_Parameters_ID#TK_Touchprint_IO.


Codec 8 Extended should be selected as the main data protocol in the “Protocol Settings” tab, which is located in the “System” section.

[[Category:]]

Retrieved from "https://wiki.teltonika-gps.com/index.php?title=Template:FMX640_Thermograph&oldid=79217"