Changes

To properly use Euroscan with FMX640 these steps must be followed:

To properly use Euroscan with FMX640 these steps must be followed:

*In FMX640 RS232 settings '''Euroscan mode''' is selected and '''Baudrate set to 38400'''

*In FMX640 RS232 settings '''Euroscan mode''' is selected and '''Baudrate set to 38400'''

*'''Partner mode enabled''' on Euroscan 600

*'''Partner mode enabled''' on Euroscan  

<br></br>

<br></br>

[[File:ReeferIO.png]]

[[File:ReeferIO.png]]

<br></br>

<br></br>

Data sending parameters (AVL ID) used for "DataCold Reefer" are these: 10040 - 10649. For more in-depth information, please refer to '''[[{{{model|}}}_Teltonika_Data_Sending_Parameters_ID#Reefer_IO]].'''

Data sending parameters (AVL ID) used for "DataCold Reefer" are these: 10040 - 10649. For more in-depth information, please refer to '''[[{{{model|}}}_Teltonika_Data_Sending_Parameters_ID#Reefer_IO|Reefer IO data sending parameters]].'''

==== TK Transcan2 Reefer ====

==== TK Transcan2 Reefer ====

<br></br>

<br></br>

Data sending parameters (AVL ID) used for "Transcan2  

Data sending parameters (AVL ID) used for "Transcan2  

" are these: 10683 - 10694. For more in-depth information, please refer to '''[[{{{model|}}}_Teltonika_Data_Sending_Parameters_ID#TK_Transcan_IO.'''

" are these: 10683 - 10694. For more in-depth information, please refer to '''[[{{{model|}}}_Teltonika_Data_Sending_Parameters_ID#TK_Transcan_IO|Transcan IO data sending parameters]]'''

==== Euroscan IO====

==== Euroscan IO====

[[File:EuroScanIO.png]]

[[File:EuroScanIO.png]]

<br></br>

<br></br>

Data sending parameters (AVL ID) used for "Euroscan" are these: 484-489 and 10464-10467. For more in-depth information, please refer to '''[[{{{model|}}}_Teltonika_Data_Sending_Parameters_ID#TK_Euroscan_IO]].'''

Data sending parameters (AVL ID) used for "Euroscan" are these: 484-489 and 10464-10467. For more in-depth information, please refer to '''[[{{{model|}}}_Teltonika_Data_Sending_Parameters_ID#TK_Euroscan_IO|Euroscan IO data sending parameters]].'''

==== TK Touchprint/Touchlog I/O ====

==== TK Touchprint/Touchlog I/O ====

[[File:TouchprintIO.png]]

[[File:TouchprintIO.png]]

<br></br>

<br></br>

Data sending parameters (AVL ID) used for "Touchprint Reefer" are these: 10695 - 10703. For more in-depth information, please refer to '''[[{{{model|}}}_Teltonika_Data_Sending_Parameters_ID#TK_Touchprint_IO]].'''

Data sending parameters (AVL ID) used for "Touchprint Reefer" are these: 10695 - 10703. For more in-depth information, please refer to '''[[{{{model|}}}_Teltonika_Data_Sending_Parameters_ID#TK_Touchprint_IO|Touchprint IO data sending parameters]].'''

[[Codec#Codec_8_Extended |Codec 8 Extended]] should be selected as the main data protocol in the “Protocol Settings” tab, which is located in the “System” section.

[[Codec#Codec_8_Extended |Codec 8 Extended]] should be selected as the main data protocol in the “Protocol Settings” tab, which is located in the “System” section.

[[Category:{{{model|}}} Manual]]

[[Category:{{{model|}}} Manual]]