Difference between revisions of "EYE FUNCTIONALITIES"

From Wiki Knowledge Base | Teltonika GPS
(55 intermediate revisions by 2 users not shown)
Line 1: Line 1:
−
__TOC__
+
This will describe functionalities when they were added and their flow.
−
=== Page Description ===
 
  
−
This page will describe EYE device functionalities, their value flow and required hardware, firmware and software versions.
 
  
−
==EYE APP 1.2.2-89==
+
Functionalities:
−
===Search device with QR scan===
 
−
'''Functionality''': Now you can find devices with QR scan by pressing scan button [[File:EYE_APP_QR_BUTTON.png|frameless|25x25px]] and scanning device QR code.
 
  
−
'''Firmware''': 1.2.1.R.0+
+
Connecting to the device
 +
{| class="nd-othertables_2" style="width:100%;"
 +
|+
 +
!
 +
! Supported SW versions
 +
! colspan="5" |EYE APP: 1.2.0-60+
 +
Firmware: 1.2.1.R.0 to 1.2.8.R.2
 +
|-
 +
|Step No.
 +
|1
 +
|2
 +
|3
 +
|
 +
|
 +
|-
 +
| Short step desc.
 +
|Tap the selected device to connect to it
 +
|Enter PIN
 +
|Connected
 +
|
 +
|
 +
|-
 +
|Successful attempt at functionality visual
 +
|[[File:TapToConnect.png|alt=|left]]
 +
|[[File:PIN_Code.png|alt=|left]]
 +
|[[File:Overview_-_with_an_update_(beacon).png|alt=|left]]
 +
|
 +
|
 +
|-
 +
|Short step desc.
 +
|Tap the selected device to connect to it
 +
|Enter PIN incorrectly
 +
|Fail to enter PIN correctly 4 more times
 +
| Wait for 5 min timeout and enter PIN incorrectly
 +
|Fail to enter PIN correctly 4 more times
 +
|-
 +
|Additional desc.
 +
|
 +
|
 +
|Device is locked for 5 min but will allow to connect with PIN again after timeout
 +
|
 +
|Device is locked for 5 min but will allow to connect with PIN again after timeout, thus this is continued in infinite loop.
 +
|-
 +
| Failed attempt at functionality visual
 +
|[[File:TapToConnect.png|alt=|left]]
 +
|[[File:PIN Code (error).png|File:PIN_Code_(error).png|alt=|left]]
 +
|[[File:Device blocked.png|alt=Device blocked|alt=|left]]
 +
|[[File:PIN Code (error).png|File:PIN_Code_(error).png|alt=|left]]
 +
|[[File:Device blocked.png|alt=Device blocked|alt=|left]]
 +
|-
 +
!Supported SW versions
  
−
'''Value''': Easier device management
+
! colspan="5" |EYE APP: 1.2.0-60+
 +
Firmware: 1.2.9.R.8+
 +
|-
 +
|Short step desc.
 +
|Tap the selected device to connect to it
 +
| Enter PIN incorrectly
 +
|Fail to enter PIN correctly 4 more times
 +
|Wait for 5 min timeout and enter PIN incorrectly
 +
|Fail to enter PIN correctly 4 more times
 +
|-
 +
|Additional desc.
 +
|
 +
|
 +
|Device is locked for 5 min but will allow to connect with PIN again after timeout
 +
|
 +
|Device is locked with PUK code now and will remain so until correct PUK is entered, see PUK code unlock.
 +
|-
 +
|Failed attempt at functionality visual
 +
|[[File:TapToConnect.png|alt=|left]]
 +
|[[File:PIN Code (error).png|File:PIN_Code_(error).png|alt=|left]]
 +
|[[File:Device blocked.png|alt=Device blocked|alt=|left]]
 +
|[[File:PIN Code (error).png|File:PIN_Code_(error).png|alt=|left]]
 +
|[[File:Device blocked (PUK).png|alt=Device blocked|alt=|left]]
 +
|}
  
−
'''Flow:''' 1. Tap [[File:EYE_APP_QR_BUTTON.png|frameless|25x25px]] 2. scan the QR code engraved onto EYE device <br><br>[[File:EYE_APP_QR_PRESS_BUTTON.png|frameless|250px]][[File:EYE_APP_QR_SCAN.png|frameless|250px]][[File:EYE_APP_QR_SCAN_EXAMPLE.png|frameless|250px]]
 
  
−
===Customized Sensor Selection===
+
PUK code unlock:
−
'''Functionality''': Users can disable sensors reading  leaving only the sensors they require.
 
  
−
'''Firmware''': 1.2.10.R.4+
+
{| class="wikitable"
 +
|+
 +
!Step No.
 +
! 1
 +
!2
 +
!3
 +
|-
 +
|Short step desc.
 +
|Tap the blocked device to connect to it
 +
|Enter PUK
 +
|Connected
 +
|-
 +
|Additional desc.
 +
|
 +
|
 +
|PIN automatically resets to default
 +
|-
 +
|Successful attempt at functionality visual
 +
|
 +
[[File:TapToConnect.png|alt=|left]]
 +
|[[File:PUK Code.png|<nowiki>File:PUK Code.png]</nowiki>|alt=|left]]
 +
|[[File:Connected PIN reset.png|alt=|left]]
 +
|-
 +
|Step desc.
 +
|Tap the selected device to connect to it
 +
|Enter PUK incorrectly
 +
| Fail to enter PIN correctly 4 more times
 +
|-
 +
|Additional desc.
 +
|
 +
|PUK is rejected and you can only go back or enter correct PUK
 +
|
 +
|-
 +
|Failed attempt at functionality visual
 +
|[[File:TapToConnect.png|alt=|left]]
 +
|[[File:PUK Code (error).png|File:PUK Code (error).png|alt=|left]]
 +
|
 +
|-
 +
|Suppoted versions
  
−
'''Value''': Data saving, battery life can be expanded by disabling accelerometer.
+
|EYE APP: 1.2.0-60+
  
−
'''Flow:''' 1. Connect to EYE device  2. Click "configure"  3. Expand Active sensors tab 4. Uncheck sensors you want to deactivate 4. Save your configuration.<br><br>[[File:EYE_APP_CHOOSE_ONE_SENSORS.png|frameless|250px]][[File:EYE_APP_ONE_SENSOR_VIEW.png|frameless|250px]][[File:EYE_APP_CHOOSE_FOUR_SENSORS.png|frameless|250px]][[File:EYE_APP_FOUR_SENSOR_VIEW.png|frameless|250px]]
+
Firmware: 1.2.9.R.8+
−
 
+
|
−
===Auto-Disconnect Timer===
+
|
−
'''Functionality''': After 2 minutes of inactivity, users will be automatically disconnected from the device. Before disconnection, you will have the option to maintain the connection.
+
|}
−
 
 
−
'''Firmware''': 1.2.10.R.4+
 
−
 
 
−
'''Value''': Enhanced privacy and energy saving.
 
−
 
 
−
'''Flow:''' 1. Connect to EYE device  2.  Do not perform any saving actions for 2 minutes.<br><br>[[File:EYE_APP_TWO_MINUTE_WAIT.png|frameless|250px]][[File:EYE_APP_DISCONNECTED_AFTER_TWO_MINUTES.png|frameless|250px]][[File:EYE_APP_DISCONNECTED_WHILE_CONFIGURING.png|frameless|250px]]
 
−
 
 
−
===Battery voltage display===
 
−
'''Functionality''': Eye App now provides a clear and convenient readout of the battery's voltage level, keeping users informed about their device's power status.
 
−
 
 
−
'''Firmware''': 1.2.1.R.0+
 
−
 
 
−
'''Value''': Keeping users informed about their device's power status.
 
−
 
 
−
'''Flow:''' 1. Expand sensor card in the overview screen or connect to the device<br><br>[[File:EYE_APP_VISIBLE_BATTERY_VOLTAGE.png|frameless|250px]]
 
−
 
 
−
===12 characters name===
 
−
'''Functionality''': Users can now assign names of up to 12 characters,
 
−
 
 
−
'''Firmware''': 1.2.1.R.0+
 
−
 
 
−
'''Value''':  A full MAC address can be used as the name.
 
−
 
 
−
'''Flow:''' 1. Connect to EYE device  2. Click "configure"  3. Expand Name settings drop down 4. Enter desired name  4. Save your configuration.<br>[[File:EYE APP 12 CHAR NAME.png|frameless|250px]]
 
−
 
 
−
==<big>EYE APP 1.2.0-63</big>==
 
−
 
 
−
===PIN code===
 
−
'''Functionality''': Eye App will time-out users on for 5 minutes after 5 unsuccessful PIN attempts
 
−
 
 
−
'''Firmware''': 1.2.1.R.0 to 1.2.8.R.2
 
−
 
 
−
'''Value''': Enhanced privacy
 
−
 
 
−
'''Flow:''' 1. Tap the selected device to connect to it 2. Enter PIN incorrectly, fail to enter PIN correctly 4 more times 3. Wait 5 minutes for timeout to end.
 
−
 
 
−
[[File:Screenshot 20230503 165303 EYE APP edited.jpg|frameless|250px]][[File:Screenshot 20230509 1518232 EYE APP.jpg|frameless|250px]][[File:Screenshot 20230509 152802 EYE APP.jpg|frameless|250px]]
 
−
 
 
−
===PUK code ===
 
−
'''Functionality''': Eye App will block users that fail PIN 10 times.
 
−
 
 
−
'''Firmware''': 1.2.9.R.8+
 
−
 
 
−
'''Value''': Enhanced privacy
 
−
 
 
−
'''Lock flow:''' 1. Tap the selected device to connect to it 2. Enter PIN incorrectly, fail to enter PIN correctly 4 more times 3. Wait 5 minutes for timeout to end. 4. Tap the selected device to connect to it 5. Enter PIN incorrectly, fail to enter PIN correctly 4 more times. 6. Requirement to enter PUK code will now appear. PUK code is provided by support.
 
−
 
 
−
[[File:Screenshot 20230503 165303 EYE APP edited.jpg|frameless|200px]][[File:Screenshot 20230509 1518232 EYE APP.jpg|frameless|200px]][[File:Screenshot 20230509 152802 EYE APP.jpg|frameless|200px]][[File:Screenshot 20230509 151823 EYE APP.jpg|frameless|200px]][[File:Screenshot 20230509 175501 EYE APP PinnAttemptAfter5min.jpg|frameless|200px]]
 
−
 
 
−
'''Unlock flow:''' 1. Tap the blocked device to connect to it 2. Enter PUK correctly 3. You will be connected, PIN will be reset to default
 
−
 
 
−
[[File:Screenshot 20230503 165303 EYE APP edited.jpg|frameless|200px]][[File:Device screen 1.2.8 2.jpg|frameless|200px]]
 
−
[[File:PUK insert.jpg|frameless|200px]]
 
−
 
 
−
===Hibernate mode:===
 
−
'''Functionality''': Eye App will allow users to send their devices back to hibernate mode
 
−
 
 
−
'''Firmware''': 1.2.9.R.8+
 
−
 
 
−
Hardware: BTSID1 hibernate version or any BTSMP1
 
−
 
 
−
'''Value''': Battery saving
 
−
 
 
−
'''Wake up flow:''' 1. Take magnet 2. Attach magnet to hibernating device 3. Wait for LED to blink.
 
−
 
 
−
[[File:520746_Magnet_EYE_gif_v1.6-min.gif|alt=|left|240x240px|link=https://wiki.teltonika-gps.com/view/File:520746_Magnet_EYE_gif_v1.6-min.gif]]<br>
 
−
 
 
−
 
 
−
 
 
−
 
 
−
 
 
−
 
 
−
 
 
−
'''Send to hibernate flow:''' 1. While connected and in overview tap "Send device to sleep". 2. Confirm your selection 3. Wait for EYE App to disconnect:
 
−
 
 
−
[[File:Device screen 1.2.8 2.jpg|400x400px]][[File:Screenshot 20230509 173323 EYE APP.jpg|400x400px]][[File:Screenshot 20230512 164509 Gallery.jpg|400x400px]]
 

Revision as of 12:43, 17 April 2023

This will describe functionalities when they were added and their flow.


Functionalities:

Connecting to the device

Supported SW versions EYE APP: 1.2.0-60+

Firmware: 1.2.1.R.0 to 1.2.8.R.2

Step No. 1 2 3
Short step desc. Tap the selected device to connect to it Enter PIN Connected
Successful attempt at functionality visual
Short step desc. Tap the selected device to connect to it Enter PIN incorrectly Fail to enter PIN correctly 4 more times Wait for 5 min timeout and enter PIN incorrectly Fail to enter PIN correctly 4 more times
Additional desc. Device is locked for 5 min but will allow to connect with PIN again after timeout Device is locked for 5 min but will allow to connect with PIN again after timeout, thus this is continued in infinite loop.
Failed attempt at functionality visual
Supported SW versions EYE APP: 1.2.0-60+

Firmware: 1.2.9.R.8+

Short step desc. Tap the selected device to connect to it Enter PIN incorrectly Fail to enter PIN correctly 4 more times Wait for 5 min timeout and enter PIN incorrectly Fail to enter PIN correctly 4 more times
Additional desc. Device is locked for 5 min but will allow to connect with PIN again after timeout Device is locked with PUK code now and will remain so until correct PUK is entered, see PUK code unlock.
Failed attempt at functionality visual


PUK code unlock:

Step No. 1 2 3
Short step desc. Tap the blocked device to connect to it Enter PUK Connected
Additional desc. PIN automatically resets to default
Successful attempt at functionality visual
Step desc. Tap the selected device to connect to it Enter PUK incorrectly Fail to enter PIN correctly 4 more times
Additional desc. PUK is rejected and you can only go back or enter correct PUK
Failed attempt at functionality visual
Suppoted versions EYE APP: 1.2.0-60+

Firmware: 1.2.9.R.8+

Retrieved from "https://wiki.teltonika-gps.com/index.php?title=EYE_FUNCTIONALITIES&oldid=84729"