Difference between revisions of "FTC921 System"
From Wiki Knowledge Base | Teltonika GPS
(Replaced content with "{{template:FTX88X/FTX9XX System|model=FTC921}}") Tag: Replaced |
|||
| (5 intermediate revisions by one other user not shown) | |||
| Line 1: | Line 1: | ||
| − | {{ | + | ==Ignition settings== |
| + | [[File:FTC921_Ignition_settings.png|right|300 px]] | ||
| + | Ignition source will be used to determine ignition of vehicle. | ||
| + | |||
| + | {{{ignition_source|Possible ignition sources: | ||
| + | {{{txt_din1|* '''DIN 1''' (Digital Input 1) - if ''DIN1'' is 1 - ignition is ON; if ''DIN1'' value is 0 - ignition is OFF;}}} | ||
| + | * '''Power Voltage''' - if voltage is between High Voltage Level and Low Voltage Level (below ''Ignition Settings'' options) - ignition is ON; if voltage is higher than High Voltage Level or lower than Low Voltage Level - ignition is OFF. | ||
| + | |||
| + | * '''Accelerometer''' - if movement sensor detects movement - ignition is ON; if movement is not detected - ignition is OFF; | ||
| + | More than one ignition source can be selected at the same moment. When there are 2 or more sources selected, at least one condition has to be met to change Ignition status.<br> | ||
| + | |||
| + | {{{txt_example|'''Example:''' DIN1 and Accelerometer are selected as the Ignition source. When the device detects movement, Ignition status will change to 1, regardless that DIN1 value is 0. Users can select movement start and movement stop delay time - those parameters are used when the accelerometer is selected as an ignition source. }}}}}} | ||
| + | Ignition status is used in power management and the following functionalities: [[{{{model|FMB1YX}}} Features settings#Eco/Green Driving|Eco/Green Driving]], [[{{{model|FMB1YX}}} Accelerometer Features settings#Excessive Idling|Excessive Idling]], Fuel Consumption, [[{{{model|FMB1YX}}} Features settings#Over Speeding|Over Speeding]], [[{{{model|FMB1YX}}} Accelerometer Features settings#Towing Detection|Towing Detection]] and [[{{{model|FMB1YX}}} Trip/Odometer settings|Trip]].<br> | ||
| + | <!--'''Note:''' Object motion detection settings, where user can configure {{{txt_num|4}}} ways how {{{model|FMB1YX}}} detects movement and change its working mode (for more information refer to section {{{ctrDaq|[[{{{model|Template:}}} Data acquisition settings]]}}}). Other functionalities that depend on movement source are: power manager, fuel consumption and trip;}}}--> | ||
| + | |||
| + | |||
| + | |||
| + | ==Movement settings== | ||
| + | [[File:FTC921_Movement_settings.png|right|300 px]] | ||
| + | Movement source will be used to determine when a vehicle is on stop or moving.<br> | ||
| + | Possible movement sources: | ||
| + | * '''Ignition''' - if ignition (based on ignition source) is ON, Vehicle MOVING mode is used; if the ignition is OFF, Vehicle on STOP mode is used; | ||
| + | * '''Accelerometer''' (movement) - if accelerometer detects movement, Vehicle MOVING mode is used; if there is no movement detected, Vehicle on STOP mode is used; | ||
| + | * '''GNSS''' - if GPS fix is acquired and speed >= 5 km/h vehicle MOVING mode is used; if GPS speed <5 km/h, Vehicle on STOP mode is used; | ||
| + | |||
| + | ==GNSS settings== | ||
| + | In ''GNSS Source'' settings user can configure which GNSS system(s) to use.<br /> | ||
| + | [[File:FTC921_GNSS_settings.png|right|300 px]] | ||
| + | '''List of configurable GNSS sources:''' | ||
| + | * GPS | ||
| + | * GPS + GLONASS | ||
| + | * GPS + Galileo | ||
| + | * GPS + BeiDou | ||
| + | * GPS + GLONASS + Galileo + BeiDou | ||
| + | |||
| + | ==Accelerometer motion detection delays== | ||
| + | [[File:FMC921_Accelerometer_motion_detection_delay.png|right|300 px]] | ||
| + | ''Accelerometer Delay Settings'' will be use to set timeout of delay when will be detected accelerometer status changes.<br></br> | ||
| + | '''Note:''' these settings impact ignition/movement sources.<br> | ||
| + | The user can set: | ||
| + | * '''Motion start detection delay''' - movement start delay in seconds; | ||
| + | * '''Motion stop detection delay''' - movement stop delay in seconds; | ||
| + | |||
| + | |||
| + | |||
| + | |||
| + | |||
| + | |||
| + | |||
| + | ==Sleep settings== | ||
| + | [[File:FTC921_Sleep_settings.png|right|300 px]] | ||
| + | |||
| + | [[Category:FTC921 Configuration]] | ||
Revision as of 14:35, 26 May 2023
Ignition settings
Ignition source will be used to determine ignition of vehicle.
Possible ignition sources:
- DIN 1 (Digital Input 1) - if DIN1 is 1 - ignition is ON; if DIN1 value is 0 - ignition is OFF;
- Power Voltage - if voltage is between High Voltage Level and Low Voltage Level (below Ignition Settings options) - ignition is ON; if voltage is higher than High Voltage Level or lower than Low Voltage Level - ignition is OFF.
- Accelerometer - if movement sensor detects movement - ignition is ON; if movement is not detected - ignition is OFF;
More than one ignition source can be selected at the same moment. When there are 2 or more sources selected, at least one condition has to be met to change Ignition status.
Example: DIN1 and Accelerometer are selected as the Ignition source. When the device detects movement, Ignition status will change to 1, regardless that DIN1 value is 0. Users can select movement start and movement stop delay time - those parameters are used when the accelerometer is selected as an ignition source.
Ignition status is used in power management and the following functionalities: Eco/Green Driving, Excessive Idling, Fuel Consumption, Over Speeding, Towing Detection and Trip.
Movement settings
Movement source will be used to determine when a vehicle is on stop or moving.
Possible movement sources:
- Ignition - if ignition (based on ignition source) is ON, Vehicle MOVING mode is used; if the ignition is OFF, Vehicle on STOP mode is used;
- Accelerometer (movement) - if accelerometer detects movement, Vehicle MOVING mode is used; if there is no movement detected, Vehicle on STOP mode is used;
- GNSS - if GPS fix is acquired and speed >= 5 km/h vehicle MOVING mode is used; if GPS speed <5 km/h, Vehicle on STOP mode is used;
GNSS settings
In GNSS Source settings user can configure which GNSS system(s) to use.
List of configurable GNSS sources:
- GPS
- GPS + GLONASS
- GPS + Galileo
- GPS + BeiDou
- GPS + GLONASS + Galileo + BeiDou
Accelerometer motion detection delays
Accelerometer Delay Settings will be use to set timeout of delay when will be detected accelerometer status changes.
Note: these settings impact ignition/movement sources.
The user can set:
- Motion start detection delay - movement start delay in seconds;
- Motion stop detection delay - movement stop delay in seconds;
Sleep settings
