Difference between revisions of "Template:FMB First start config"

From Wiki Knowledge Base | Teltonika GPS
m
(97 intermediate revisions by 20 users not shown)
Line 1: Line 1:
{{{PCConnection|
 
===PC Connection (Windows)===
 
  
{{{fmb_powerup|# Power-up {{{model|FMB1YX}}} with '''DC voltage {{{dc_voltage|(10 – 30 V)}}}''' power supply {{{additional_power_supply|}}} using '''{{{power_cable|supplied power cable}}}'''. LED’s should start blinking, see “'''{{{led_status_link|LED behaviour description}}}'''”.}}}
+
<font size="+3"><span style=color:#104996>'''How to install {{{model|FMB1YX}}} drivers (Windows)'''</span></font>
# Connect device to computer using '''{{{usb_cable|Micro-USB}}} cable'''{{{Bluetooth®_connection| or '''Bluetooth®''' connection:  
 
#* Using '''{{{usb_cable|Micro-USB}}} cable'''
 
#** You will need to install USB drivers, see "[[#How to install USB drivers (Windows)|'''How to install USB drivers (Windows)''']]"
 
#* Using '''Bluetooth®'''
 
#** {{{model|FMB1YX}}} Bluetooth® is enabled by default. Turn on '''Bluetooth®''' on your PC, then select '''Add Bluetooth® or other device > Bluetooth®'''. Choose your device named – “'''{{{model|FMB1YX}}}_last_7_imei_digits'''”, without '''LE''' in the end. Enter default password '''5555''', press '''Connect''' and then select '''Done'''.}}}
 
# You are now ready to use the device on your computer.
 
}}}
 
===How to install USB drivers (Windows)===
 
  
# Please download COM port drivers from '''[[Media:TeltonikaCOMDriver.zip|here]]'''.
+
<font size="+2"><span style=color:#F49E21> 1. </span> Please download COM port drivers from Teltonika website: https://teltonika.lt/?media_dl=5543. </font>
# Extract and run '''TeltonikaCOMDriver.exe'''.
 
# Click '''Next''' in driver installation window.
 
# In the following window click '''Install''' button.
 
# Setup will continue installing the driver and eventually the confirmation window will appear. Click '''Finish''' to complete the setup.
 
  
===Configuration (Windows)===
+
<font size="+2"><span style=color:#F49E21> 2. </span> Extract and run <span style=color:#F6A83E>TeltonikaCOMDriver.exe</span>. This driver is used to detect {{{model|FMB1YX}}} device when it is connected to the computer. </font>
  
At first {{{model|FMB1YX}}} device will have default factory settings set. These settings should be changed according to the user's needs.<br/>
+
<font size="+2"><span style=color:#F49E21> 3. </span> Click <span style=color:#F6A83E>Next</span> in driver installation window. </font>
Main configuration can be performed via '''[[Teltonika Configurator]]''' software. Get the latest {{{model|FMB1YX}}} '''Configurator''' version from '''[[{{{SAS_Configurator_Versions|Teltonika Configurator versions}}}|here]]'''. Configurator operates on Microsoft Windows OS and uses prerequisite MS .NET Framework. Make sure you have the correct version installed.
 
  
{| class="wikitable" style="width:50%;"
+
<font size="+2"><span style=color:#F49E21> 4. </span> In the following window click <span style=color:#F6A83E>Install</span> button. </font>
|+
 
! colspan="4" style="width:50%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: left;"| MS .NET requirements
 
|-
 
! style="width:10%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: left;"| Operating system
 
! style="width:25%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: left;"| MS .NET Framework version
 
! style="width:10%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: left;"| Version
 
! style="width:5%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: left;"| Link
 
|-
 
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | <ul style="list-style: none; margin: 0px;">
 
<li>Windows Vista</li>
 
<li>Windows 7</li>
 
<li>Windows 8.1</li>
 
<li>Windows 10</li>
 
</ul>
 
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | {{{MS .NET Framework|MS .NET Framework 5.0}}}
 
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | 32 and 64 bit
 
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | {{{MS .NET Framework link|[https://dotnet.microsoft.com/en-us/download/dotnet-framework/net462 .NET Framework]}}}
 
|}
 
  
Downloaded '''Configurator''' will be in compressed archive. Extract it and launch '''Configurator.exe'''. After launch software language can be changed by clicking [[File:Language_logo.png|25px|link=]] in the right bottom corner:
+
<font size="+2"><span style=color:#F49E21> 5. </span> Setup will continue installing the driver and afterwards, the confirmation window will appear. Click <span style=color:#F6A83E>Finish</span> to complete the setup. You are now ready to use the device on your computer. </font>
  
[[File:FMB_Configurator_languag.jpg|400px]]
 
  
Configuration process begins by pressing on connected device:
 
  
[[File:{{{cfg_connect|Configurator_connect-FMB150.jpg}}}|400px]]
+
<font size="+3"><span style=color:#104996>'''Configuration (Windows)'''</span></font><br/>
  
After connection to Configurator '''Status window''' will be displayed:
+
<font size="+2"><span style=color:#104996>.NET requirements</span></font>
{{{Status window image|[[Image:{{{model|FMB120}}} Beacon-info-{{{family|FMB1}}} series.png|1000px|none]]}}}
 
  
 +
{| class="wikitable"
 +
|+
 +
! style="background: white; color: #F6A83E;"        | Operating system
 +
| style="background: white; color: #F6A83E;"        | MS .NET Framework version
 +
| style="background: white; color: #F6A83E;"        | Version
 +
| style="background: white; color: #F6A83E;"        | Links
 +
|-
 +
| style="text-align: left; background: #F6F6FB;" rowspan="2"        | Windows XP with SP3 or later
 +
| style="text-align: left; background: #F6F6FB;" rowspan="2"        | MS .NET Framework 4 with KB2468871-v2 update
 +
| style="text-align: left; background: #F6F6FB;"        | 32 and 64 bit
 +
| style="text-align: left; background: #F6F6FB;"        | https://www.microsoft.com/en-US/Download/confirmation.aspx?id=17718
 +
http://avl1.teltonika.lt/downloads/software/Framework/.NET%20Framework%204/dotNetFx40_Full_x86_x64.exe
 +
|-
 +
| style="text-align: left; background: #F6F6FB;"        | 32 bit (x86) , 64 bit (x64 or IA64)
 +
| style="text-align: left; background: #F6F6FB;"        | https://www.microsoft.com/en-us/download/details.aspx?id=3556
 +
http://avl1.teltonika.lt/downloads/software/Framework/.NET%20Framework%204%20update%20KB2468871-v2/
 +
|-
 +
| style="text-align: left; background: #F6F6FB;"        | Windows Vista<br/>Windows 7<br/>Windows 8.1<br/>Windows 10
 +
| style="text-align: left; background: #F6F6FB;"        | MS .NET Framework 4.6.2
 +
| style="text-align: left; background: #F6F6FB;"        | 32 and 64 bit
 +
| style="text-align: left; background: #F6F6FB;"        | https://www.microsoft.com/en-us/download/confirmation.aspx?id=53344
 +
http://avl1.teltonika.lt/downloads/software/Framework/.NET%20Framework%204.6.2/NDP462-KB3151800-x86-x64-AllOS-ENU.exe
 +
|-
 +
|}
  
Various '''[[{{{model|FMB1YX}}}_Status_info|Status window]]''' tabs display information about '''[[{{{model|FMB1YX}}}_Status_info#GNSS_Info|GNSS]], [[{{{model|FMB1YX}}}_Status_info#GSM_Info|GSM]], [[{{{model|FMB1YX}}}_Status_info#I.2FO_Info|I/O]], [[{{{model|FMB1YX}}}_Status_info#Maintenance|Maintenance]]''' and etc. {{{model|FMB1YX}}} has one user editable profile, which can be loaded and saved to the device. After any modification of configuration the changes need to be saved to device using '''Save to device''' button. Main buttons offer following functionality:<br/>
+
<font size="+2">
# [[File:Load_from_device.png|25px|link=]] '''Load from device''' – loads configuration from device.
+
At first {{{model|FMB1YX}}} device will have default factory settings set. These settings should be changed according to the user's needs.<br/>
# [[File:Save_to_device.png|25px|link=]] '''Save to device''' – saves configuration to device.
+
Device can be configured to acquire and send data to server, in this case the GSM settings shall be set in regards with GSM operator's information. If device GSM is unavailable, the device will not be able to send the data and FMB120 will start storing records to flash memory. It is possible to store up to 192000 data records with 128 MB SD memory card (when 100 MB are used to store records). It will send data over GPRS when it is available. Note that {{{model|FMB1YX}}} might reach its full memory capacity. If such case happens, the device will start deleting the oldest records in order to save new ones.<br/>
# [[File:Load_from_file.png|25px|link=]] '''Load from file''' – loads configuration from file.
+
FMB120 configuration is performed via {{{model|FMB1YX}}} Configurator program. Contact sales manager to get the latest {{{model|FMB1YX}}} Configurator version or download from https://teltonika.lt/?media_dl=7290. {{{model|FMB1YX}}} configurator operates on Microsoft Windows OS and uses prerequisite MS .NET Framework.
# [[File:Save_to_file.png|25px|link=]] '''Save to file''' – saves configuration to file.
 
# {{{Firmware_button| [[File:Firmware_update.png|25px|link=]] '''Update firmware''' – updates firmware on device.}}}
 
# [[File:Read_records.png|25px|link=]] '''Read records''' – read records from device.
 
# [[File:Reboot_device.png|25px|link=]] '''Reboot device''' – restarts device.
 
# [[File:Reset_configuration.png|25px|link=]] '''Reset configuration''' – sets device configuration to default.
 
  
Most important configurator section is GPRS – where all your server and '''[[{{{model|FMB1YX}}}_GPRS_settings|GPRS settings]]''' can be configured and '''[[{{{model|FMB1YX}}}_Data_acquisition_settings|Data Acquisition]]''' – where data acquiring parameters can be configured.
+
[[Image:Fmb120_configurator.png|1200px|center]]
More details about {{{model|FMB1YX}}} configuration using Configurator can be found '''{{{config_link|in the manual}}}'''.
+
Module configuration can be performed over USB cable or using a Bluetooth port. Configuration process begins by starting {{{model|FMB1YX}}} Configurator software and then connecting to {{{model|FMB1YX}}} device via <span style=color:#F6A83E>Connect</span> button located in <span style=color:#F6A83E>Online</span> menu part. {{{model|FMB1YX}}} has one user editable profile, which can be loaded from device, and saved. After any modification of configuration the changes have to be saved to FMB120 device using <span style=color:#F6A83E>Save to device</span> button.<br/>
 +
Main buttons offer following functionality:<br/>
 +
* <span style=color:#F6A83E>Load from device</span> – loads configuration from device.
 +
* <span style=color:#F6A83E>Save to device</span> – saves configuration to device.
 +
* <span style=color:#F6A83E>Load from file</span> – loads configuration from file.
 +
* <span style=color:#F6A83E>Save to file</span> – saves configuration to file.
 +
* <span style=color:#F6A83E>Update firmware</span> – updates firmware on device.
 +
* <span style=color:#F6A83E>Reset device</span> – sets device configuration to default.
  
===Quick SMS configuration===
+
More details on using the Configurator can be found {{{config_link|in the manual}}}.
 +
</font>
  
Default configuration has optimal parameters present to ensure best performance of track quality and data usage.<br/>
 
Quickly set up your device by sending this SMS command to it:
 
  
"  setparam <span style="background-color:#91b9d4;">2001</span>:APN;<span style="background-color:#91d4b9;">2002</span>:APN_username;<span style="background-color:#b991d4;">2003</span>:APN_password;<span style="background-color:#b9d491;">2004</span>:Domain;<span style="background-color:#d491b9;">2005</span>:Port;<span style="background-color:#d4b991;">2006</span>:0"
+
<font size="+3"><span style=color:#104996>'''Mounting recommendations'''</span></font>
  
<div style="column-count:2;-moz-column-count:2;-webkit-column-count:2">
+
<font size="+2"><span style=color:#F49E21> 1. </span> Connecting wires </font>
GPRS settings:
+
<font size="+1">
* <span style="background-color:#91b9d4;">2001</span> – APN
+
* Wires should be connected while the module is not plugged in.
* <span style="background-color:#91d4b9;">2002</span> – APN username (if there are no APN username, empty field should be left)
+
* Wires should be fastened to stable wires or other non-moving parts. Any heat emitting and/or moving objects should be kept away from the wires.
* <span style="background-color:#b991d4;">2003</span> – APN password (if there are no APN password, empty field should be left)
+
* There should be no exposed wires. If factory isolation was removed while connecting the wires, the isolation material should be applied.
Server settings:
+
* If the wires are placed in the exterior or in places where they can be damaged or exposed to heat, humidity, dirt, etc., additional isolation should be applied and the wires should not be loose.
* <span style="background-color:#b9d491;">2004</span> – Domain
+
* Wires cannot be connected to the board computers or control units.
* <span style="background-color:#d491b9;">2005</span> – Port
+
</font>
* <span style="background-color:#d4b991;">2006</span> – Data sending protocol (0 – TCP, 1 – UDP)
+
<font size="+2"><span style=color:#F49E21> 2. </span> Connecting power source. </font>
</div>
+
<font size="+1">
 +
* Be sure that after the car computer goes to sleep mode, power might be still available on the power wires. Depending on the car model, this may happen in 5 to 30 minutes period.
 +
* When the module is connected, measure the voltage again to make sure it did not decrease.
 +
* It is recommended to connect to the main power cable in the fuse box.
 +
* 3 A, 125 V external fuse shall be used.
 +
</font>
 +
<font size="+2"><span style=color:#F49E21> 3. </span> Connecting ignition wire. </font>
 +
<font size="+1">
 +
* Be sure to check if it is a real ignition wire i. e. power does not disappear after starting the engine.
 +
* Check if this is not an ACC wire (when key is in the first position, most of the vehicle electronics are available).
 +
* Check if power is still available when you turn off any of vehicles devices.
 +
* Ignition is connected to the ignition relay output. As alternative, any other relay, which has power output when ignition is on, may be chosen.
 +
</font>
 +
<font size="+2"><span style=color:#F49E21> 4. </span> Connecting ground wire. </font>
 +
<font size="+1">
 +
* Ground wire is connected to the vehicle frame or metal parts that are fixed to the frame.
 +
* If the wire is fixed with the bolt, the loop must be connected to the end of the wire.
 +
* For better contact scrub paint from the spot where loop is going to be connected.
 +
</font>
  
'''Note''': Before SMS text, two space symbols should be inserted.<br/><br/>
 
[[File:IOS sms cfg.png|235px|right]]
 
  
{{{quick_sms_tmt|<table style="width:70%">
+
<font size="+3"><span style=color:#FF0000>'''Safety information'''</span></font><br/>
  <tr>
+
<font size="+2">
    <td colspan="4">'''Default configuration settings'''</td>
+
This message contains information on how to operate {{{model|FMB1YX}}} safely. By following these requirements and recommendations, you will avoid dangerous situations. You must read these instructions carefully and follow them strictly before operating the device!<br/>
  </tr>
+
The device uses SELV limited power source. The nominal voltage is +12 V DC. The allowed range of voltage is +10-30 V DC.<br/>
  <tr>
+
To avoid mechanical damage, it is advised to transport the device in an impact-proof package. Before usage, the device should be placed so that its LED indicators are visible. They show the status of device operation.<br/>
    <td colspan="4">Movement and ignition detection:</td>
+
When connecting the 2x6 connector wires to the vehicle, the appropriate jumpers of the vehicle power supply should be disconnected.<br/>
  </tr>
+
Before unmounting the device from the vehicle, the 2x6 connector must be disconnected.<br/>
  <tr>
+
The device is designed to be mounted in a zone of limited access, which is inaccessible to the operator. All related devices must meet the requirements of EN 60950-1 standard.<br/>
    <td>[[File:Accelerometer.png|65px]]</td>
+
The device FMB120 is not designed as a navigational device for boats.<br/>
    <td>Vehicle movement will be detected by accelerometer</td>
+
</font>
    <td>[[File:Ignition detection-2-2.png|65px]]</td>
 
    <td>Ignition will be detected by vehicle power voltage between 13,2 – 30 V</td>
 
  </tr>
 
  <tr>
 
    <td colspan="4">Device makes a record '''On Moving''' if one of these events happen:</td>
 
  </tr>
 
  <tr>
 
    <td>[[File:300s_icon_2.png|65px]]</td>
 
    <td>300 seconds passes</td>
 
    <td>[[File:Angle_10_2.png|65px]]</td>
 
    <td>Vehicle turns 10° degrees</td>
 
  </tr>
 
  <tr>
 
    <td>[[File:Min_distance.png|65px]]</td>
 
    <td>Vehicle drives 100 meters</td>
 
    <td>[[File:Speed_delta.png|65px]]</td>
 
    <td>Speed difference between last coordinate and current position is greater than 10 km/h</td>
 
  </tr>
 
  <tr>
 
    <td colspan="4">Device makes a record '''On Stop''' if:</td>
 
  </tr>
 
  <tr>
 
    <td>[[File:1h_icon.png|65px]]</td>
 
    <td>1 hour passes while vehicle is stationary and ignition is off</td>
 
  </tr>
 
  <tr>
 
    <td colspan="4">Records sending to server:</td>
 
  </tr>
 
  <tr>
 
    <td>[[File:120_s.png|65px]]</td>
 
    <td>If device has made a record it is sent to the server every 120 seconds</td>
 
  </tr>
 
</table>}}}
 
  
<br/>
+
 
<p>After successful SMS configuration, {{{model|FMB1YX}}} device will '''synchronize time''' and '''update records''' to '''configured server'''. Time intervals and default I/O elements can be changed by using [[Teltonika Configurator]] or {{{SMS/GPRS Commands|[[Template:FMB Device Family Parameter list|SMS parameters]]}}}.</p>
+
<font size="+3"><span style=color:#104996>'''Precautions'''</span></font>
 +
<font size="+2">
 +
{| class="wikitable" style="border-style: solid; border-width: 0px"
 +
|+
 +
|-
 +
| style="text-align: left; background: #F6F6FB;"        | [[Image:Bw_nb.png|50px]]
 +
| style="text-align: left; background: #F6F6FB;"        | Do not disassemble the device. If the device is damaged, the power supply cables are not isolated or the isolation is damaged, DO NOT touch the device before unplugging the power supply.
 +
|-
 +
| style="text-align: left; background: #F6F6FB;"        | [[Image:Bw_nb.png|50px]]
 +
| style="text-align: left; background: #F6F6FB;"        | All wireless data transferring devices produce interference that may affect other devices which are placed nearby.
 +
|-
 +
| style="text-align: left; background: #F6F6FB;"        | [[Image:Bw_key.png|50px]]
 +
| style="text-align: left; background: #F6F6FB;"        | The device must be connected only by qualified personnel.
 +
|-
 +
| style="text-align: left; background: #F6F6FB;"        | [[Image:Bw_tick.png|50px]]
 +
| style="text-align: left; background: #F6F6FB;"        | The device must be firmly fastened in a predefined location.
 +
|-
 +
| style="text-align: left; background: #F6F6FB;"        | [[Image:Bw_tick.png|50px]]
 +
| style="text-align: left; background: #F6F6FB;"        | The programming must be performed using a PC with autonomic power supply.
 +
|-
 +
| style="text-align: left; background: #F6F6FB;"        | [[Image:Bw_humidity.png|50px]]
 +
| style="text-align: left; background: #F6F6FB;"        | The device is susceptible to water and humidity.
 +
|-
 +
| style="text-align: left; background: #F6F6FB;"        | [[Image:Bw_ecute.png|50px]]
 +
| style="text-align: left; background: #F6F6FB;"        | Installation and/or handling during a lightning storm is prohibited.
 +
|}
 +
</font>

Revision as of 17:03, 26 April 2018

How to install FMB1YX drivers (Windows)

1. Please download COM port drivers from Teltonika website: https://teltonika.lt/?media_dl=5543.

2. Extract and run TeltonikaCOMDriver.exe. This driver is used to detect FMB1YX device when it is connected to the computer.

3. Click Next in driver installation window.

4. In the following window click Install button.

5. Setup will continue installing the driver and afterwards, the confirmation window will appear. Click Finish to complete the setup. You are now ready to use the device on your computer.


Configuration (Windows)

.NET requirements

Operating system MS .NET Framework version Version Links
Windows XP with SP3 or later MS .NET Framework 4 with KB2468871-v2 update 32 and 64 bit https://www.microsoft.com/en-US/Download/confirmation.aspx?id=17718

http://avl1.teltonika.lt/downloads/software/Framework/.NET%20Framework%204/dotNetFx40_Full_x86_x64.exe

32 bit (x86) , 64 bit (x64 or IA64) https://www.microsoft.com/en-us/download/details.aspx?id=3556

http://avl1.teltonika.lt/downloads/software/Framework/.NET%20Framework%204%20update%20KB2468871-v2/

Windows Vista
Windows 7
Windows 8.1
Windows 10
MS .NET Framework 4.6.2 32 and 64 bit https://www.microsoft.com/en-us/download/confirmation.aspx?id=53344

http://avl1.teltonika.lt/downloads/software/Framework/.NET%20Framework%204.6.2/NDP462-KB3151800-x86-x64-AllOS-ENU.exe

At first FMB1YX device will have default factory settings set. These settings should be changed according to the user's needs.
Device can be configured to acquire and send data to server, in this case the GSM settings shall be set in regards with GSM operator's information. If device GSM is unavailable, the device will not be able to send the data and FMB120 will start storing records to flash memory. It is possible to store up to 192000 data records with 128 MB SD memory card (when 100 MB are used to store records). It will send data over GPRS when it is available. Note that FMB1YX might reach its full memory capacity. If such case happens, the device will start deleting the oldest records in order to save new ones.
FMB120 configuration is performed via FMB1YX Configurator program. Contact sales manager to get the latest FMB1YX Configurator version or download from https://teltonika.lt/?media_dl=7290. FMB1YX configurator operates on Microsoft Windows OS and uses prerequisite MS .NET Framework.

Fmb120 configurator.png

Module configuration can be performed over USB cable or using a Bluetooth port. Configuration process begins by starting FMB1YX Configurator software and then connecting to FMB1YX device via Connect button located in Online menu part. FMB1YX has one user editable profile, which can be loaded from device, and saved. After any modification of configuration the changes have to be saved to FMB120 device using Save to device button.
Main buttons offer following functionality:

  • Load from device – loads configuration from device.
  • Save to device – saves configuration to device.
  • Load from file – loads configuration from file.
  • Save to file – saves configuration to file.
  • Update firmware – updates firmware on device.
  • Reset device – sets device configuration to default.

More details on using the Configurator can be found in the manual.


Mounting recommendations

1. Connecting wires

  • Wires should be connected while the module is not plugged in.
  • Wires should be fastened to stable wires or other non-moving parts. Any heat emitting and/or moving objects should be kept away from the wires.
  • There should be no exposed wires. If factory isolation was removed while connecting the wires, the isolation material should be applied.
  • If the wires are placed in the exterior or in places where they can be damaged or exposed to heat, humidity, dirt, etc., additional isolation should be applied and the wires should not be loose.
  • Wires cannot be connected to the board computers or control units.

2. Connecting power source.

  • Be sure that after the car computer goes to sleep mode, power might be still available on the power wires. Depending on the car model, this may happen in 5 to 30 minutes period.
  • When the module is connected, measure the voltage again to make sure it did not decrease.
  • It is recommended to connect to the main power cable in the fuse box.
  • 3 A, 125 V external fuse shall be used.

3. Connecting ignition wire.

  • Be sure to check if it is a real ignition wire i. e. power does not disappear after starting the engine.
  • Check if this is not an ACC wire (when key is in the first position, most of the vehicle electronics are available).
  • Check if power is still available when you turn off any of vehicles devices.
  • Ignition is connected to the ignition relay output. As alternative, any other relay, which has power output when ignition is on, may be chosen.

4. Connecting ground wire.

  • Ground wire is connected to the vehicle frame or metal parts that are fixed to the frame.
  • If the wire is fixed with the bolt, the loop must be connected to the end of the wire.
  • For better contact scrub paint from the spot where loop is going to be connected.


Safety information
This message contains information on how to operate FMB1YX safely. By following these requirements and recommendations, you will avoid dangerous situations. You must read these instructions carefully and follow them strictly before operating the device!
The device uses SELV limited power source. The nominal voltage is +12 V DC. The allowed range of voltage is +10-30 V DC.
To avoid mechanical damage, it is advised to transport the device in an impact-proof package. Before usage, the device should be placed so that its LED indicators are visible. They show the status of device operation.
When connecting the 2x6 connector wires to the vehicle, the appropriate jumpers of the vehicle power supply should be disconnected.
Before unmounting the device from the vehicle, the 2x6 connector must be disconnected.
The device is designed to be mounted in a zone of limited access, which is inaccessible to the operator. All related devices must meet the requirements of EN 60950-1 standard.
The device FMB120 is not designed as a navigational device for boats.


Precautions

Bw nb.png Do not disassemble the device. If the device is damaged, the power supply cables are not isolated or the isolation is damaged, DO NOT touch the device before unplugging the power supply.
Bw nb.png All wireless data transferring devices produce interference that may affect other devices which are placed nearby.
Bw key.png The device must be connected only by qualified personnel.
Bw tick.png The device must be firmly fastened in a predefined location.
Bw tick.png The programming must be performed using a PC with autonomic power supply.
Bw humidity.png The device is susceptible to water and humidity.
Bw ecute.png Installation and/or handling during a lightning storm is prohibited.