Jump to content
  • EN

EYE FUNCTIONALITIES: Difference between revisions

From Teltonika Telematics Wiki
← Older edit
VisualWikitext
 
(29 intermediate revisions by 2 users not shown)
Line 1: Line 1:
__TOC__
__TOC__
=== Description ===
=== Page Description ===


This page will describe EYE device functionalities, their flow and functionality supporting software versions.
This page will describe EYE device functionalities, their value flow and required hardware, firmware and software versions.  


==== Functionalities: ====
==EYE APP 1.2.2-89==
===Search device with QR scan===
'''Functionality''': Now you can find devices with QR scan by pressing scan button [[File:EYE_APP_QR_BUTTON.png|frameless|25x25px]] and scanning device QR code.


===== Connecting to the device =====
'''Firmware''': 1.2.1.R.0+
{| class="nd-othertables_2" style="width:100%;"
!SW version requirements
! colspan="5" | EYE APP: 1.2.0-60+
Firmware: 1.2.1.R.0 to 1.2.8.R.2
|-
|Step No.
|1
|2
|3
|
|
|-
| Short step desc.
|Tap the selected device to connect to it
|Enter PIN
|Connected
|
|
|-
|Successful attempt at functionality visual
|[[File:TapToConnect.png|alt=|left]]
|[[File:PIN_Code.png|alt=|left]]
|[[File:Overview_-_with_an_update_(beacon).png|alt=|left]]
|
|
|-
|Short step desc.
|Tap the selected device to connect to it
|Enter PIN incorrectly
|Fail to enter PIN correctly 4 more times
| Wait for 5 min timeout and enter PIN incorrectly
|Fail to enter PIN correctly 4 more times
|-
|Additional desc.
|
|
|Device is locked for 5 min but will allow to connect with PIN again after timeout
|
|Device is locked for 5 min but will allow to connect with PIN again after timeout, thus this is continued in infinite loop.
|-
| Failed attempt at functionality visual
|[[File:TapToConnect.png|alt=|left]]
|[[File:PIN Code (error).png|File:PIN_Code_(error).png|alt=|left]]
|[[File:Device blocked.png|alt=Device blocked|alt=|left]]
|[[File:PIN Code (error).png|File:PIN_Code_(error).png|alt=|left]]
|[[File:Device blocked.png|alt=Device blocked|alt=|left]]
|}


'''Value''': Easier device management


'''Flow:''' 1. Tap [[File:EYE_APP_QR_BUTTON.png|frameless|25x25px]] 2. scan the QR code engraved onto EYE device <br><br>[[File:EYE_APP_QR_PRESS_BUTTON.png|frameless|250px]][[File:EYE_APP_QR_SCAN.png|frameless|250px]][[File:EYE_APP_QR_SCAN_EXAMPLE.png|frameless|250px]]


===Customized Sensor Selection===
'''Functionality''': Users can disable sensors reading  leaving only the sensors they require.


'''Firmware''': 1.2.10.R.4+


'''Value''': Data saving, battery life can be expanded by disabling accelerometer.


{| class="nd-othertables_2" style="width:100%;"
'''Flow:''' 1. Connect to EYE device  2. Click "configure"  3. Expand Active sensors tab 4. Uncheck sensors you want to deactivate 4. Save your configuration.<br><br>[[File:EYE_APP_CHOOSE_ONE_SENSORS.png|frameless|250px]][[File:EYE_APP_ONE_SENSOR_VIEW.png|frameless|250px]][[File:EYE_APP_CHOOSE_FOUR_SENSORS.png|frameless|250px]][[File:EYE_APP_FOUR_SENSOR_VIEW.png|frameless|250px]]
!SW version requirements
! colspan="5" | EYE APP: 1.2.0-60+
Firmware: 1.2.9.R.8+
|-
|Short step desc.
|Tap the selected device to connect to it
| Enter PIN incorrectly
|Fail to enter PIN correctly 4 more times
|Wait for 5 min timeout and enter PIN incorrectly
|Fail to enter PIN correctly 4 more times
|-
|Additional desc.
|
|
|Device is locked for 5 min but will allow to connect with PIN again after timeout
|
|Device is locked with PUK code now and will remain so until correct PUK is entered, see PUK code unlock.
|-
|Failed attempt at functionality visual
|[[File:TapToConnect.png|alt=|left]]
|[[File:PIN Code (error).png|File:PIN_Code_(error).png|alt=|left]]
|[[File:Device blocked.png|alt=Device blocked|alt=|left]]
|[[File:PIN Code (error).png|File:PIN_Code_(error).png|alt=|left]]
|[[File:Device blocked (PUK).png|alt=Device blocked|alt=|left]]
|}


===== PUK code unlock: =====
===Auto-Disconnect Timer===
{| class="nd-othertables_2" style="width:60%;"
'''Functionality''': After 2 minutes of inactivity, users will be automatically disconnected from the device. Before disconnection, you will have the option to maintain the connection.  
!SW version requirements
! colspan="5" | EYE APP: 1.2.0-60+
Firmware: 1.2.9.R.8+
|-
|Step No.
|
|-
|Short step desc.
|Tap the blocked device to connect to it
|Enter PUK
|Connected
|-
|Additional desc.
|
|
|PIN automatically resets to default
|-
|Successful attempt at functionality visual
|
[[File:TapToConnect.png|alt=|left]]
|[[File:PUK Code.png|<nowiki>File:PUK Code.png]</nowiki>|alt=|left]]
|[[File:Connected PIN reset.png|alt=|left]]
|-
|Step desc.
|Tap the selected device to connect to it
|Enter PUK incorrectly
| Fail to enter PIN correctly 4 more times
|-
|Additional desc.
|
|PUK is rejected and you can only go back or enter correct PUK
|
|-
|Failed attempt at functionality visual
|[[File:TapToConnect.png|alt=|left]]
|[[File:PUK Code (error).png|File:PUK Code (error).png|alt=|left]]
|
|}


'''Firmware''': 1.2.10.R.4+


===== Hibernate mode: =====
'''Value''': Enhanced privacy and energy saving.


====== Wake up: ======
'''Flow:''' 1. Connect to EYE device  2. Do not perform any saving actions for 2 minutes.<br><br>[[File:EYE_APP_TWO_MINUTE_WAIT.png|frameless|250px]][[File:EYE_APP_DISCONNECTED_AFTER_TWO_MINUTES.png|frameless|250px]][[File:EYE_APP_DISCONNECTED_WHILE_CONFIGURING.png|frameless|250px]]
{| class="nd-othertables_2" style="width:60%;"
!SW version requirements
! colspan="5" |Firmware: 1.2.9.R.8+
|-
|Step No.
|1-3
|4
|
|-
|Short step desc.
|Attach magnet to sleeping device and wait for LED to blink.
|Device starts broacasting
|
|-
|Additional desc.
|
|Now device is discoverabled, scannable, connectable via BLE.
|
|-
|Successful attempt at functionality visual
|[[File:520746_Magnet EYE gif v1.6-min.gif]]
|
|
|}


====== Send to sleep: ======
===Battery voltage display===
{| class="nd-othertables_2" style="width:100%;"
'''Functionality''': Eye App now provides a clear and convenient readout of the battery's voltage level, keeping users informed about their device's power status.
!SW version requirements
 
! colspan="3" |EYE APP: 1.2.0-60+
'''Firmware''': 1.2.1.R.0+
Firmware: 1.2.9.R.8+
 
|-
'''Value''': Keeping users informed about their device's power status.
|Step No.
 
|1
'''Flow:''' 1. Expand sensor card in the overview screen or connect to the device<br><br>[[File:EYE_APP_VISIBLE_BATTERY_VOLTAGE.png|frameless|250px]]
|2
 
|3
===12 characters name===
|-
'''Functionality''': Users can now assign names of up to 12 characters,
|Short step desc.
 
|Attach magnet to sleeping device and wait for LED to blink.
'''Firmware''': 1.2.1.R.0+
|Device starts broacasting
 
|
'''Value''':  A full MAC address can be used as the name.
|-
 
|Additional desc.
'''Flow:''' 1. Connect to EYE device  2. Click "configure" 3. Expand Name settings drop down 4. Enter desired name  4. Save your configuration.<br>[[File:EYE APP 12 CHAR NAME.png|frameless|250px]]
|
 
|Now device is discoverabled, scannable, connectable via BLE.
==<big>EYE APP 1.2.0-63</big>==
|
 
|-
===PIN code===
|Successful attempt at functionality visual
'''Functionality''': Eye App will time-out users on for 5 minutes after 5 unsuccessful PIN attempts
|[[File:Send_To_Sleep.png|alt=|left]]
 
|[[File:Send_To_Sleep_Confirm.png|alt=|left]]
'''Firmware''': 1.2.1.R.0 to 1.2.8.R.2
|[[File:Send_To_Sleep_Disconnect.png|alt=|left]]
 
|}
'''Value''': Enhanced privacy
 
'''Flow:''' 1. Tap the selected device to connect to it 2. Enter PIN incorrectly, fail to enter PIN correctly 4 more times 3. Wait 5 minutes for timeout to end.
 
[[File:Screenshot 20230503 165303 EYE APP edited.jpg|frameless|250px]][[File:Screenshot 20230509 1518232 EYE APP.jpg|frameless|250px]][[File:Screenshot 20230509 152802 EYE APP.jpg|frameless|250px]]
 
===PUK code ===
'''Functionality''': Eye App will block users that fail PIN 10 times.
 
'''Firmware''': 1.2.9.R.8+
 
'''Value''': Enhanced privacy
 
'''Lock flow:''' 1. Tap the selected device to connect to it 2. Enter PIN incorrectly, fail to enter PIN correctly 4 more times 3. Wait 5 minutes for timeout to end. 4. Tap the selected device to connect to it 5. Enter PIN incorrectly, fail to enter PIN correctly 4 more times. 6. Requirement to enter PUK code will now appear. PUK code is provided by support.
 
[[File:Screenshot 20230503 165303 EYE APP edited.jpg|frameless|200px]][[File:Screenshot 20230509 1518232 EYE APP.jpg|frameless|200px]][[File:Screenshot 20230509 152802 EYE APP.jpg|frameless|200px]][[File:Screenshot 20230509 151823 EYE APP.jpg|frameless|200px]][[File:Screenshot 20230509 175501 EYE APP PinnAttemptAfter5min.jpg|frameless|200px]]
 
'''Unlock flow:''' 1. Tap the blocked device to connect to it 2. Enter PUK correctly 3. You will be connected, PIN will be reset to default
 
[[File:Screenshot 20230503 165303 EYE APP edited.jpg|frameless|200px]][[File:Device screen 1.2.8 2.jpg|frameless|200px]]
[[File:PUK insert.jpg|frameless|200px]]
 
===Hibernate mode:===
'''Functionality''': Eye App will allow users to send their devices back to hibernate mode
 
'''Firmware''': 1.2.9.R.8+
 
Hardware: BTSID1 hibernate version or any BTSMP1
 
'''Value''': Battery saving
 
'''Wake up flow:''' 1. Take magnet 2. Attach magnet to hibernating device 3. Wait for LED to blink.
 
[[File:520746_Magnet_EYE_gif_v1.6-min.gif|alt=|left|240x240px|link=https://wiki.teltonika-gps.com/view/File:520746_Magnet_EYE_gif_v1.6-min.gif]]<br>
 
 
 
 
 
 
 
'''Send to hibernate flow:''' 1. While connected and in overview tap "Send device to sleep". 2. Confirm your selection 3. Wait for EYE App to disconnect:
 
[[File:Device screen 1.2.8 2.jpg|400x400px]][[File:Screenshot 20230509 173323 EYE APP.jpg|400x400px]][[File:Screenshot 20230512 164509 Gallery.jpg|400x400px]]

Latest revision as of 16:06, 8 December 2023

Page Description

This page will describe EYE device functionalities, their value flow and required hardware, firmware and software versions.

EYE APP 1.2.2-89

Search device with QR scan

Functionality: Now you can find devices with QR scan by pressing scan button and scanning device QR code.

Firmware: 1.2.1.R.0+

Value: Easier device management

Flow: 1. Tap 2. scan the QR code engraved onto EYE device

Customized Sensor Selection

Functionality: Users can disable sensors reading leaving only the sensors they require.

Firmware: 1.2.10.R.4+

Value: Data saving, battery life can be expanded by disabling accelerometer.

Flow: 1. Connect to EYE device 2. Click "configure" 3. Expand Active sensors tab 4. Uncheck sensors you want to deactivate 4. Save your configuration.

Auto-Disconnect Timer

Functionality: After 2 minutes of inactivity, users will be automatically disconnected from the device. Before disconnection, you will have the option to maintain the connection.

Firmware: 1.2.10.R.4+

Value: Enhanced privacy and energy saving.

Flow: 1. Connect to EYE device 2. Do not perform any saving actions for 2 minutes.

Battery voltage display

Functionality: Eye App now provides a clear and convenient readout of the battery's voltage level, keeping users informed about their device's power status.

Firmware: 1.2.1.R.0+

Value: Keeping users informed about their device's power status.

Flow: 1. Expand sensor card in the overview screen or connect to the device

12 characters name

Functionality: Users can now assign names of up to 12 characters,

Firmware: 1.2.1.R.0+

Value: A full MAC address can be used as the name.

Flow: 1. Connect to EYE device 2. Click "configure" 3. Expand Name settings drop down 4. Enter desired name 4. Save your configuration.

EYE APP 1.2.0-63

PIN code

Functionality: Eye App will time-out users on for 5 minutes after 5 unsuccessful PIN attempts

Firmware: 1.2.1.R.0 to 1.2.8.R.2

Value: Enhanced privacy

Flow: 1. Tap the selected device to connect to it 2. Enter PIN incorrectly, fail to enter PIN correctly 4 more times 3. Wait 5 minutes for timeout to end.

PUK code

Functionality: Eye App will block users that fail PIN 10 times.

Firmware: 1.2.9.R.8+

Value: Enhanced privacy

Lock flow: 1. Tap the selected device to connect to it 2. Enter PIN incorrectly, fail to enter PIN correctly 4 more times 3. Wait 5 minutes for timeout to end. 4. Tap the selected device to connect to it 5. Enter PIN incorrectly, fail to enter PIN correctly 4 more times. 6. Requirement to enter PUK code will now appear. PUK code is provided by support.

Unlock flow: 1. Tap the blocked device to connect to it 2. Enter PUK correctly 3. You will be connected, PIN will be reset to default

Hibernate mode:

Functionality: Eye App will allow users to send their devices back to hibernate mode

Firmware: 1.2.9.R.8+

Hardware: BTSID1 hibernate version or any BTSMP1

Value: Battery saving

Wake up flow: 1. Take magnet 2. Attach magnet to hibernating device 3. Wait for LED to blink.





Send to hibernate flow: 1. While connected and in overview tap "Send device to sleep". 2. Confirm your selection 3. Wait for EYE App to disconnect:

Retrieved from "https://wiki.teltonika-gps.com/index.php?title=EYE_FUNCTIONALITIES&oldid=93594"