Template:FMB9 First start card: Difference between revisions

← Older edit

VisualWikitext

Latest revision as of 12:02, 15 December 2023

Small and smart tracker with Bluetooth®

How to insert Micro-SIM card

Gently remove FMB9YX cover using plastic pry tool from both sides.
Insert Micro-SIM card as shown with PIN request disabled or read Security info how to enter it later in Configurator. Make sure that Micro-SIM card cut-off corner is pointing forward to slot.
Attach device cover back.
Device is ready to be connected.

Gently remove FMB9YX cover using plastic pry tool from both sides.
Insert Micro-SIM card as shown with PIN request disabled or read Security info how to enter it later in Configurator. Make sure that Micro-SIM card cut-off corner is pointing forward to slot.
Connect the battery as shown on device. Position the battery in place where it does not obstruct other components.
Attach device cover back. Device is ready to be connected.

Micro-SIM card insertion/removal must be performed when device is powered off – external voltage and internal battery disconnected. Otherwise Micro-SIM card might be damaged or device will not detect it.

@@ Line 1: / Line 1: @@
 [[Image:Qsg_rut950_teltonika.PNG|centre]]
-<b>{{{description|Small and smart tracker with Blue-tooth}}}</b>
+<b>{{{description|Small and smart tracker with Bluetooth®}}}</b>
 {{{pic|[[Image:Fmb920 main.png|400px|right]]}}}
 <br>
@@ Line 11: / Line 11: @@
 =='''How to insert Micro-SIM card'''==
-*Insert Micro-SIM card as shown with PIN request disabled or
+{{{without_battery|
-read our Wiki how to enter PIN later in Teltonika
+# Gently remove {{{model|FMB9YX}}} '''cover''' using '''plastic pry tool''' from both sides.
-Configurator. Make sure that Micro-SIM card cut-off corner is
+# Insert '''{{{sim_type|Micro-}}}SIM''' card as shown with '''PIN request disabled''' or read {{{sim_pin|[[{{{model|FMB9YX}}} Security info|'''Security info''']]}}} how to enter it later in Configurator. Make sure that {{{sim_type|Micro-}}}SIM card '''cut-off corner''' is pointing forward to slot.
-pointing forward to slot.
+# Attach device '''cover''' back.
-*Connect battery as shown to device.
+# Device is ready to be connected.}}}
-*Connect micro usb cable as shown
-*To power up TST100, connect green plug to the E-scooter
-*Open Teltonika configurator, select TST100 device and
-configure it according to your requirements (how to install
-drives on page
-*Once all done, disconnect TST100 from PC and E-scooter. Attach
-the lid by two screws as shown
-[[Image:Fmb920_cover_1.png|280px]][[Image:Fmb920_cover_2.png|280px]][[Image:Fmb920_cover_3.png|280px]][[Image:Fmb920_cover_4.png|280px]]
+{{{with_battery|
+# Gently remove {{{model|FMB9YX}}} '''cover''' using '''plastic pry tool''' from both sides.
+# Insert '''{{{sim_type|Micro-}}}SIM''' card as shown with '''PIN request disabled''' or read {{{sim_pin|[[{{{model|FMB9YX}}} Security info|'''Security info''']]}}} how to enter it later in Configurator. Make sure that {{{sim_type|Micro-}}}SIM card '''cut-off corner''' is pointing forward to slot.
+# Connect the battery as shown on device. Position the battery in place where it does not obstruct other components.
+# Attach device '''cover''' back. Device is ready to be connected.}}}
+{{{SIM1|[[Image:FMB9_sim_ir_battery_insert-1.png|260px]]}}}
+{{{SIM2|[[Image:FMB9_sim_ir_battery_insert-2.png|260px]]}}}
+{{{SIM3|[[Image:FMB9_sim_ir_battery_insert-3.png|260px]]}}}
+{{{SIM4|[[Image:FMB9_sim_ir_battery_insert-4.png|260px]]}}}