Difference between revisions of "Mobile Signal Strength Recommendations"
(Created page with "== Summary == This chapter is an overview of recommended signal strength levels for different mobile service modes. == Signal Measurement == Signal strength values are define...") |
|||
| (2 intermediate revisions by the same user not shown) | |||
| Line 7: | Line 7: | ||
The measurements are as follows: | The measurements are as follows: | ||
| − | * | + | * RSSI |
| − | * | + | * RSRP |
| − | * | + | * SINR |
More on these measurements in separate service mode sections. | More on these measurements in separate service mode sections. | ||
| − | == Determining Factors of Signal | + | == Determining Factors of Signal Values == |
Many different factors influence signal strength and quality, including but not limited to: | Many different factors influence signal strength and quality, including but not limited to: | ||
| Line 27: | Line 27: | ||
== 2G (GSM) == | == 2G (GSM) == | ||
| − | 2G (GSM) Signal strength is defined by only one value: '''RSSI''' | + | 2G (GSM) Signal strength is defined by only one value: '''RSSI''' – Received Signal Strength Indicator; RSSI is a negative value, and the closer to 0, the stronger the signal. |
| − | '''RSSI''' | + | '''RSSI -''' Received Signal Strength Indicator. RSSI is a negative value, and the closer to 0, the stronger the signal |
[[File:2G RSSI.png|left|frameless|1154x1154px]] | [[File:2G RSSI.png|left|frameless|1154x1154px]] | ||
| Line 40: | Line 40: | ||
To check the 2G signal strength value of your Teltonika Telematics device, go to configurator → I/O tab → check GSM Signal value: | To check the 2G signal strength value of your Teltonika Telematics device, go to configurator → I/O tab → check GSM Signal value: | ||
| − | [[File:Checking RSSI.png|center|frameless|1124x1124px]] | + | [[File:Checking RSSI.png|center|frameless|1124x1124px]] |
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
== 4G (LTE) == | == 4G (LTE) == | ||
When checking LTE/4G signal strength, we should be looking at SINR and RSRP values. | When checking LTE/4G signal strength, we should be looking at SINR and RSRP values. | ||
| − | '''SINR''' | + | '''SINR -''' Signal to Interference plus Noise Ratio. Indicates the throughput capacity of the channel. As the name implies, SINR is the strength of the signal divided by the strength of any interference |
| − | [[File:SINR.png|frameless|1151x1151px]]'''RSRP''' | + | [[File:SINR.png|frameless|1151x1151px]]'''RSRP -''' the Reference Signal Received Power is the power of the LTE Reference Signals spread over the full bandwidth and narrowband |
[[File:RSRP.png|frameless|1153x1153px]] | [[File:RSRP.png|frameless|1153x1153px]] | ||
| Line 79: | Line 56: | ||
Go to configurator → I/O tab → check Connectivity Quality element which provides detailed signal quality information in LTE (only RSSI), eMTC and NB-IoT modes. | Go to configurator → I/O tab → check Connectivity Quality element which provides detailed signal quality information in LTE (only RSSI), eMTC and NB-IoT modes. | ||
| − | [[File:Connectivity quality.png|center|frameless|1100x1100px]] | + | [[File:Connectivity quality.png|center|frameless|1100x1100px]] |
| − | |||
| − | |||
Revision as of 15:51, 19 March 2024
Summary
This chapter is an overview of recommended signal strength levels for different mobile service modes.
Signal Measurement
Signal strength values are defined by a few different measurements which vary even more for different service modes, this page will cover the most relevant measurements for evaluating signal quality with Teltonika Telematics devices.
The measurements are as follows:
- RSSI
- RSRP
- SINR
More on these measurements in separate service mode sections.
Determining Factors of Signal Values
Many different factors influence signal strength and quality, including but not limited to:
- Tower load
- Proximity to the cellular tower
- Signal going through a cellular repeater
- Competing signals
- Physical barriers (mountains, buildings, trains, etc.)
- Weather
Therefore, measurements like Signal Strength (RSSI) do not incorporate all of the relevant factors to describe the quality of the connection. For example, you may have an excellent RSSI value of -51 dBm, but the Tower Load (the number of mobile users) in your area is very high. In this case, even though you have a great Signal Strength value, you may not achieve maximum mobile data speeds.
2G (GSM)
2G (GSM) Signal strength is defined by only one value: RSSI – Received Signal Strength Indicator; RSSI is a negative value, and the closer to 0, the stronger the signal.
RSSI - Received Signal Strength Indicator. RSSI is a negative value, and the closer to 0, the stronger the signal
To check the 2G signal strength value of your Teltonika Telematics device, go to configurator → I/O tab → check GSM Signal value:
4G (LTE)
When checking LTE/4G signal strength, we should be looking at SINR and RSRP values.
SINR - Signal to Interference plus Noise Ratio. Indicates the throughput capacity of the channel. As the name implies, SINR is the strength of the signal divided by the strength of any interference
RSRP - the Reference Signal Received Power is the power of the LTE Reference Signals spread over the full bandwidth and narrowband
To check the LTE/4G signal strength values of your telematics device
NOTE: (Only applies to FMM devices)
Go to configurator → I/O tab → check Connectivity Quality element which provides detailed signal quality information in LTE (only RSSI), eMTC and NB-IoT modes.
