312
edits
Changes
→ADAS configuration for FMx650
==FMx640 Configuration==
==FMx640 Configuration==
'''It is important to note that ONLY specific ADAS cameras starting with the Serial Number S/N: 9C can be connected and used with FMX640 devices. Cameras starting with different S/N numbers for example; 9B, are currently only supported by FMX125/225 devices.''' However, upon receipt of the cameras, if the S/N number starts with 9B, check whether there is a red circle sticker on the camera as shown in the picture below. If there is, please connect the camera to the computer, install the required drivers and visit IP 10.0.0.1 on the browser. In the further window, details about the camera is displayed where the actual S/N number of the camera will start with 9C meaning that the camera is compatible with FMX640 devices. This is due to the serial numbers being pre-attached to the camera case from the manufacturer and is kept the same for warranty purposes.
'''It is important to note that ADAS cameras with Serial Numbers (S/N) starting with "9C" are exclusively compatible with FMX640 devices. However, cameras with Serial Numbers beginning with "9B" are typically designed for use with FMX125/225 devices.''' In the event you receive a camera with a Serial Number starting with "9B," it is crucial to check for a red circle sticker on the camera. The presence of this red sticker indicates that the camera, despite its "9B" Serial Number, is actually compatible with FMX640 devices, functioning equivalently to cameras with a "9C" Serial Number. This is due to the serial numbers being pre-attached to the camera case by the manufacturer and remaining constant for warranty purposes. If your camera with a "9B" Serial Number has this red sticker, proceed to connect it to a computer, install the required drivers, and visit IP 10.0.0.1 in a browser. Here, you will find more details about the camera, which will confirm its compatibility with FMX640 devices, as the actual Serial Number displayed will start with "9C.
'''NOTE: You need to insert an SD card into the FMX640 device; otherwise, you will not receive any video or photo on the server.'''
[[File:ADAS 9B sticker.png | 250px]]
[[File:ADAS 9B sticker.png | 250px]]
{| class="wikitable" style="border-style: solid; border-width: 0px;"
| style="width: auto; text-align: left; background: #F6F6FB;" |'''NOTE!'''
| style="width: auto; text-align: left; background: #F6F6FB;" |ADAS devices which start with '''9C''' - will provide a red sticker, as shown on the picture. ADAS devices which start with '''9B''' - '''WILL NOT''' provide a red circle sticker.
The picture has been only made for explanation purposes, and does not show the real replication of the sticker for 9B.
|}
'''Device Configuration'''
'''Device Configuration'''
[[File:Adas conf2.png|center|frameless|1000x1000px]]
[[File:Adas conf2.png|center|frameless|1000x1000px]]
==ADAS configuration for FMx650==
'''(!) Required firmware version - 03.00.14.Rev.116'''. [[DSM_Firmware_errata|Firmware errata.]]
*Make sure '''Data Protocol''' is set to [[Codec#Codec_8_Extended | Codec 8 Extended]]
[[Image:Data_protocol.gif|300px]]
*In ''RS232 \ RS485 settings tab'', make sure to enable '''Camera interface''' by "Enable", and select '''ADAS''' in the Mode drop-down menu, afterwards '''ADAS COM1''' and '''Camera I/O''' should appear in the tab list.
[[Image:ADAS COM1.gif|600px]]
*Make sure to change '''Camera I/O''' camera state '''Priorities''' to ''Low''
'''
[[File:ADAS CameraIO.gif|500px]]
'''
*In appeared ''ADAS COM1'' tab, make sure to '''configure everything by your needs''', and do not forget to complete the '''"Domain"''' and '''"Port"''' settings in ''File upload settings''
[[File:ADAS.png|500px]]
*'''''NOTE:''''' ''This is a base setup for the device to work properly. Other device configuration is made according to your needs.
===Connecting two cameras simultaneously for FMx650===
------------------
The new feature for FMx650 ADAS configuration, which is available from '''03.00.14.Rev.114-Rev.116 iCamera''' allows you to connect two of your cameras at once. Method for connection and configuration stays the same, for this you are only required to choose '''two''' cameras in '''"RS232 \ RS485"''' tab from the configurator.
In the new functionality, you are able to connect any combo of the cameras by your wish, as an example: you are able to connect ''ADAS/DSM'', ''ADAS/DualCam'', ''DSM/Dualcam'', ''DashCam/DualCam'', ''DSM/DSM'', ''DualCam/DualCam'' and etc.
[[File:Twincamera.gif|500px]]
==FMx125/FMX225 Configuration==
==FMx125/FMX225 Configuration==
[[File:Adasconf1.png|center|frameless|1000x1000px]]
[[File:Adasconf1.png|center|frameless|1000x1000px]]
==Crash Detection Functionality using DOUT==
'''The crash detection feature''' is a crucial capability provided by our device. It enhances evidential documentation through video or photo evidence in the event of a crash. However, activating this functionality necessitates a direct connection of the camera to a power source. Nonetheless, such a direct connection can lead to '''battery drainage'''.
To circumvent this issue, we recommend utilizing DOUT and a relay for connection. This setup enables control via SMS or GPRS command, or through predefined scenarios within our device. By activating DOUT post-ignition, the camera receives power, allowing it to function and record evidence even after the ignition is turned off following a crash. '''For your convenience, the connection scheme can be found here: [[ADAS First Start]]'''
'''It is important to note that in the event of a fatal crash where fatalities may occur,''' we cannot guarantee the retrieval of video or photo evidence due to the severity of the accident. Moreover, both the camera and the device itself may sustain irreparable damage in such instances
[[Category:DSM]]
[[Category: Teltonika ADAS]]
[[Category: Teltonika ADAS]]
