Wiki Knowledge Base | Teltonika GPS

Changes

Template:FTX88X/FTX9XX System (view source)

Revision as of 06:52, 23 May 2024

923 bytes removed ,  23 May
→‎Power saving settings
Line 25: Line 25:  
Movement source will be used to determine when a vehicle is on stop or moving.<br>
 
Movement source will be used to determine when a vehicle is on stop or moving.<br>
 
Possible movement sources:
 
Possible movement sources:
−
* '''Accelerometer''' (movement) - if accelerometer detects movement, Vehicle MOVING mode is used; if there is no movement detected, Vehicle on STOP mode is used;
+
* '''Accelerometer''' (movement) - if the accelerometer detects movement, the Vehicle is under MOVING mode; if there is no movement detected, the Vehicle on STOP mode;
−
* '''GNSS''' - if GPS fix is acquired and speed >= 5 km/h vehicle MOVING mode is used; if GPS speed <5 km/h, Vehicle on STOP mode is used;
+
* '''GNSS''' - if GPS fix is acquired and speed >= 5 km/h vehicle then the MOVING mode is used; if GPS speed <5 km/h, the Vehicle on STOP mode is used;
−
* '''Power voltage''' - Data acquisition > "moving" mode (Parameter state = 1) - when power voltage is >= low power voltage and <= high power voltage. By default low voltage is 13.2 V and high voltage is 30 V;
+
* '''Power voltage''' - Data acquisition > "moving" mode (Parameter state = 1) - when power voltage is >= low power voltage and <= high power voltage. By default low voltage is 13.2 V and the high voltage is 30 V;
 
* '''DIN1''' - Data acquisition > "moving" mode (Parameter state = 1) - when voltage measured by DIN 1 is higher than 7.5V. Data acquisition > "on stop" mode (Parameter state = 0) - when voltage measured by DIN 1 is lower than 7.5V.
 
* '''DIN1''' - Data acquisition > "moving" mode (Parameter state = 1) - when voltage measured by DIN 1 is higher than 7.5V. Data acquisition > "on stop" mode (Parameter state = 0) - when voltage measured by DIN 1 is lower than 7.5V.
 
<br>
 
<br>
Line 54: Line 54:  
* '''Motion start delay (s)''' - movement start delay in seconds;
 
* '''Motion start delay (s)''' - movement start delay in seconds;
 
* '''Motion stop delay (s)''' - movement stop delay in seconds;
 
* '''Motion stop delay (s)''' - movement stop delay in seconds;
−
<br />
  −
<br />
  −
<br />
  −
<br />
  −
  −
==Power saving settings==
  −
[[File:FTC power saving settings.png|right|500px]]
  −
  −
This feature will be used to save power consumption of external battery (power supply). It let the user choose one of four power saving modes which he would prefer: '''[[{{{model|FTC881}}} Sleep modes#GPS Sleep mode|GPS Sleep]]''', '''[[{{{model|FTC881}}} Sleep modes#Deep Sleep mode|Deep Sleep]]''', '''[[{{{model|FTC881}}} Sleep modes#Online Deep Sleep mode|Online Deep Sleep]]''' and '''[[{{{model|FTC881}}} Sleep modes#Ultra Sleep|Ultra Deep Sleep]]'''. Also, after the mentioned options you can find the Timeout (min) parameter which starts counting when the device is in STOP mode. After timeout is reached and all conditions for sleep mode are met, the device goes to sleep mode. <br></br>
  −
'''Note:''' Detail description and conditions about every mode you can find [[{{{model|FTC881}}} Sleep modes|'''here''']].<br>
  −
<br />
  −
<br />
   
<br />
 
<br />
 
<br />
 
<br />
Retrieved from "https://wiki.teltonika-gps.com/view/Special:MobileDiff/98440...98442"