137
edits
Changes
no edit summary
Movement source will be used to determine when a vehicle is on stop or moving.<br>
Movement source will be used to determine when a vehicle is on stop or moving.<br>
Possible movement sources:
Possible movement sources:
* '''Accelerometer''' (movement) - if accelerometer detects movement, Vehicle MOVING mode is used; if there is no movement detected, Vehicle on STOP mode is used;
* '''Accelerometer''' (movement) - if the accelerometer detects movement, the Vehicle is under MOVING mode; if there is no movement detected, the Vehicle on STOP mode;
* '''GNSS''' - if GPS fix is acquired and speed >= 5 km/h vehicle MOVING mode is used; if GPS speed <5 km/h, Vehicle on STOP mode is used;
* '''GNSS''' - if GPS fix is acquired and speed >= 5 km/h vehicle then the MOVING mode is used; if GPS speed <5 km/h, the Vehicle on STOP mode is used;
* '''Power voltage''' - Data acquisition > "moving" mode (Parameter state = 1) - when power voltage is >= low power voltage and <= high power voltage. By default low voltage is 13.2 V and high voltage is 30 V;
* '''Power voltage''' - Data acquisition > "moving" mode (Parameter state = 1) - when power voltage is >= low power voltage and <= high power voltage. By default low voltage is 13.2 V and the high voltage is 30 V;
* '''DIN1''' - Data acquisition > "moving" mode (Parameter state = 1) - when voltage measured by DIN 1 is higher than 7.5V. Data acquisition > "on stop" mode (Parameter state = 0) - when voltage measured by DIN 1 is lower than 7.5V.
* '''DIN 1''' - Data acquisition > "moving" mode (Parameter state = 1) - when voltage measured by DIN 1 is higher than 7.5V. Data acquisition > "on stop" mode (Parameter state = 0) - when voltage measured by DIN 1 is lower than 7.5V.
<br>
<br>
<br>
<br>
<br>
==Configuration password==
[[File:Configuration password.png|right|500 px]]
Protects the device from unauthorized access while using USB or Bluetooth to make any form of configuration changes.
*'''Set password''' - Set the primary password for the device. Required to access the device every time using the USB or via Bluetooth connection.
*'''Recovery password (optional)''' - in the event that the primary password is forgotten, the recovery password can be used as a backup to unlock the device configuration.
<br>
<br>
<br>
<br>
<br>
<br>
<br>
<br>
<br>
<br>
<br>
<br />
<br />
==Movement delay==
==Movement delay==
[[File:FTC movement delay.png|right|500 px]]
[[File:Movement Delays.png|right|500 px]]
''Movement delay'' will be use to set timeout of delay when will be detected accelerometer status changes.<br></br>
''Movement delay'' will be used to set the timeout of delays when the accelerometer status changes.<br></br>
'''Note:''' these settings impact ignition/movement sources.<br>
'''Note:''' These settings impact the ignition/movement sources.<br>
The user can set:
The user can set:
* '''Motion start delay (s)''' - movement start delay in seconds;
* '''Movement start delay (s)''' - movement start delay in seconds;
* '''Motion stop delay (s)''' - movement stop delay in seconds;
* '''Movement stop delay (s)''' - movement stop delay in seconds;
<br />
<br />
<br />
<br />
<br />
<br />
==Power saving settings==
==Power Saving settings==
[[File:FTC power saving settings.png|right|500px]]
[[File:Power Saving Settings.png|right|500 px]]
Puts the device into a power-saving mode, preserving the power consumption from the external source or the internal battery. The device enters this mode after the conditions are met.
*The selectable modes are as follows:
'''Disable''' - Normal mode, no internal battery saving.
'''Ultra Deep Sleep''' - The device turns off almost everything to save maximum power. The device exits this mode when DIN turns 1 (ON).
*'''Timeout''' - After timeout is reached, and conditions are met for the sleep mode, the device goes into sleep mode.
<br>
<br>
==Time synchronization settings==
==Time synchronization settings==
[[image:Lenta.png|middle|580px]]
[[image:Lenta.png|middle|580px]]
==Battery settings==
==Battery settings==
'''On need'''—Battery will charge on need <br>
'''On need'''—Battery will charge on need <br>
'''After ignition ON'''—battery will be charged after the ignition source will be ON <br>
'''After ignition ON'''—Battery will start charging when the ignition source is turned ON <br>
'''Always'''—Battery will be charged all the time <br>
'''Always'''—Battery will charge all the time <br>
<br>
<br>
<br>
<br>
<br>
<br>
<br>
==LED settings==
[[File:FTC led settings.png|right|500 px]]
<br />
<br />
This feature allows disabling or enabling status and navigation LED's