Line 28: |
Line 28: |
| * '''GNSS''' - if GPS fix is acquired and speed >= 5 km/h vehicle then the MOVING mode is used; if GPS speed <5 km/h, the Vehicle on STOP mode is used; | | * '''GNSS''' - if GPS fix is acquired and speed >= 5 km/h vehicle then the MOVING mode is used; if GPS speed <5 km/h, the Vehicle on STOP mode is used; |
| * '''Power voltage''' - Data acquisition > "moving" mode (Parameter state = 1) - when power voltage is >= low power voltage and <= high power voltage. By default low voltage is 13.2 V and the high voltage is 30 V; | | * '''Power voltage''' - Data acquisition > "moving" mode (Parameter state = 1) - when power voltage is >= low power voltage and <= high power voltage. By default low voltage is 13.2 V and the high voltage is 30 V; |
− | * '''DIN1''' - Data acquisition > "moving" mode (Parameter state = 1) - when voltage measured by DIN 1 is higher than 7.5V. Data acquisition > "on stop" mode (Parameter state = 0) - when voltage measured by DIN 1 is lower than 7.5V. | + | * '''DIN 1''' - Data acquisition > "moving" mode (Parameter state = 1) - when voltage measured by DIN 1 is higher than 7.5V. Data acquisition > "on stop" mode (Parameter state = 0) - when voltage measured by DIN 1 is lower than 7.5V. |
| + | <br> |
| + | <br> |
| + | <br> |
| + | <br> |
| + | <br> |
| + | |
| + | ==Configuration password== |
| + | [[File:Configuration password.png|right|500 px]] |
| + | Protects the device from unauthorized access while using USB or Bluetooth to make any form of configuration changes. |
| + | *'''Set password''' - Set the primary password for the device. Required to access the device every time using the USB or via Bluetooth connection. |
| + | *'''Recovery password (optional)''' - in the event that the primary password is forgotten, the recovery password can be used as a backup to unlock the device configuration. |
| + | <br> |
| + | <br> |
| + | <br> |
| + | <br> |
| + | <br> |
| + | <br> |
| + | <br> |
| <br> | | <br> |
| <br> | | <br> |
Line 48: |
Line 66: |
| <br /> | | <br /> |
| ==Movement delay== | | ==Movement delay== |
− | [[File:FTC movement delay.png|right|500 px]] | + | [[File:Movement Delays.png|right|500 px]] |
− | ''Movement delay'' will be use to set timeout of delay when will be detected accelerometer status changes.<br></br> | + | ''Movement delay'' will be used to set the timeout of delays when the accelerometer status changes.<br></br> |
− | '''Note:''' these settings impact ignition/movement sources.<br> | + | '''Note:''' These settings impact the ignition/movement sources.<br> |
| The user can set: | | The user can set: |
− | * '''Motion start delay (s)''' - movement start delay in seconds; | + | * '''Movement start delay (s)''' - movement start delay in seconds; |
− | * '''Motion stop delay (s)''' - movement stop delay in seconds; | + | * '''Movement stop delay (s)''' - movement stop delay in seconds; |
| <br /> | | <br /> |
| <br /> | | <br /> |
| <br /> | | <br /> |
| <br /> | | <br /> |
| + | |
| + | ==Power Saving settings== |
| + | [[File:Power Saving Settings.png|right|500 px]] |
| + | Puts the device into a power-saving mode, preserving the power consumption from the external source or the internal battery. The device enters this mode after the conditions are met. |
| + | |
| + | *The selectable modes are as follows: |
| + | '''Disable''' - Normal mode, no internal battery saving. |
| + | |
| + | '''Ultra Deep Sleep''' - The device turns off almost everything to save maximum power. The device exits this mode when DIN turns 1 (ON). |
| + | |
| + | *'''Timeout''' - After timeout is reached, and conditions are met for the sleep mode, the device goes into sleep mode. |
| + | <br> |
| + | <br> |
| + | |
| | | |
| ==Time synchronization settings== | | ==Time synchronization settings== |
Line 75: |
Line 107: |
| [[image:Lenta.png|middle|580px]] | | [[image:Lenta.png|middle|580px]] |
| | | |
− | ==LED settings==
| |
− | [[File:FTC led settings.png|right|500 px]]
| |
− | <br />
| |
− | <br />
| |
− |
| |
− | This feature allows disabling or enabling status and navigation LED's
| |
| | | |
| ==Battery settings== | | ==Battery settings== |
Line 90: |
Line 116: |
| | | |
| '''On need'''—Battery will charge on need <br> | | '''On need'''—Battery will charge on need <br> |
− | '''After ignition ON'''—battery will be charged after the ignition source will be ON <br> | + | '''After ignition ON'''—Battery will start charging when the ignition source is turned ON <br> |
− | '''Always'''—Battery will be charged all the time <br> | + | '''Always'''—Battery will charge all the time <br> |
| + | <br> |
| + | <br> |
| + | <br> |
| + | <br> |
| + | <br> |
| + | <br> |
| + | <br> |
| | | |
− | [[Category:{{{model}}} Configuration]] | + | ==LED settings== |
| + | [[File:FTC led settings.png|right|500 px]] |
| + | <br /> |
| + | <br /> |
| + | |
| + | This feature allows disabling or enabling status and navigation LED's |