DashCam Configuration: Difference between revisions
| (10 intermediate revisions by 3 users not shown) | |||
| Line 1: | Line 1: | ||
==FMX125/225 configuration== | ==FMX125/225 configuration== | ||
*Please make sure to download the latest DashCam FW version. The latest FWs can be downloaded from the following Wiki page — [[DashCam Firmware errata]] | |||
*It is necessary to change '''Data Protocol''' to [[Codec#Codec_8_Extended | Codec 8 Extended]] | *It is necessary to change '''Data Protocol''' to [[Codec#Codec_8_Extended | Codec 8 Extended]] | ||
| Line 14: | Line 16: | ||
*'''Do not forget''' to configure ''DashCam'' server information. In '''RS232\RS485''' fill in '''DashCam Server Settings''' with ''Domain'' and ''Port'' entries. | *'''Do not forget''' to configure ''DashCam'' server information. In '''RS232\RS485''' fill in '''DashCam Server Settings''' with ''Domain'' and ''Port'' entries. | ||
[[File:Dashcamserver.png|600px]] | [[File:Dashcamserver.png|600px]] | ||
== Metadata version == | |||
From 03.29.00.Rev.534 metadata version can be configured. Version descriptions and differences are provided in section. [[DashCam Communication Protocol#Communication%20protocol|https://wiki.teltonika-gps.com/view/DashCam_Communication_Protocol#Communication_protocol]] . Default value is version 3. | |||
[[File:Metadata.png|alt=|frameless]]<br /> | |||
==FMC650 DashCam Configuration== | ==FMC650 DashCam Configuration== | ||
'''(!) Required firmware version - 03.00.14.Rev.114.''' [[DashCam Firmware errata|Firmware errata.]] | |||
*Make sure '''Data Protocol''' is set to [[Codec#Codec_8_Extended | Codec 8 Extended]] | *Make sure '''Data Protocol''' is set to [[Codec#Codec_8_Extended | Codec 8 Extended]] | ||
| Line 42: | Line 48: | ||
'' | '' | ||
===Connecting two cameras | ===Connecting two cameras simultaneously for FMx650=== | ||
------------------ | ------------------ | ||
The new feature for FMx650 | The new feature for FMx650 DashCam configuration, which is available from '''03.00.14.Rev.114 iCamera''' allows you to connect two of your cameras at once. Method for connection and configuration stays the same, for this you are only required to choose '''two''' cameras in '''"RS232 \ RS485"''' tab from the configurator. | ||
In the new functionality, you are able to connect any combo of the cameras by your wish, as an example: you are able to connect ''DashCam/Dualcam'', ''DashCam/DSM'', ''DSM/DSM'', ''DualCam/DualCam'' and etc. | |||
[[File:Twincamera.gif|500px]] | [[File:Twincamera.gif|500px]] | ||
| Line 115: | Line 123: | ||
Z1 – maximum speed value for DOUT1 if needed. | Z1 – maximum speed value for DOUT1 if needed. | ||
===Crash Detection Functionality using DOUT=== | |||
'''The crash detection feature''' is a crucial capability provided by our device. It enhances evidential documentation through video or photo evidence in the event of a crash. However, activating this functionality necessitates a direct connection of the camera to a power source. Nonetheless, such a direct connection can lead to '''battery drainage'''. | |||
To circumvent this issue, we recommend utilizing DOUT and a relay for connection. This setup enables control via SMS or GPRS command, or through predefined scenarios within our device. By activating DOUT post-ignition, the camera receives power, allowing it to function and record evidence even after the ignition is turned off following a crash. '''For your convenience, the connection scheme can be found here: [[DashCam First Start]]''' | |||
'''It is important to note that in the event of a fatal crash where fatalities may occur,''' we cannot guarantee the retrieval of video or photo evidence due to the severity of the accident. Moreover, both the camera and the device itself may sustain irreparable damage in such instances | |||
==Other camera related functionality== | ==Other camera related functionality== | ||