Changes

Line 89: Line 89:  
==GNSS Fuel Counter==
 
==GNSS Fuel Counter==
   −
[[Image:{{{model|FMB1YX}}}_GNSS_Fuel_Counter.png|{{{gnss_fuel_counter|size}}}|right]]
+
[[Image:GNSS_Fuel_Counter.gif|{{{gnss_fuel_counter|size}}}|right]]
   −
#To configure ''Fuel Counter'' parameters use fuel consumption norms which are presented in technical documentation of the vehicle. By default speeds for these fuel consumption norms are: City – 30 km/h, Average - 60 km/h, Highway - 90 km/h. These values can be changed.
+
#To configure ''Fuel Counter'' parameters use fuel consumption norms which are presented in the technical documentation of the vehicle. By default speeds for these fuel consumption norms are: City – 30 km/h, Average - 60 km/h, Highway - 90 km/h. These values can be changed.
 
#When speed is higher than the highway fuel consumption speed, x% of highway fuel consumption is added every extra y km/h, by default {{{model|FMB1YX}}} adds 20% every 50 km/h of extra speed. For example, the fuel consumption is (1.2 * (Highway Fuel Consumption)) at 140 km/h and (1.4 * (Highway Fuel Consumption)) at 190 km/h.
 
#When speed is higher than the highway fuel consumption speed, x% of highway fuel consumption is added every extra y km/h, by default {{{model|FMB1YX}}} adds 20% every 50 km/h of extra speed. For example, the fuel consumption is (1.2 * (Highway Fuel Consumption)) at 140 km/h and (1.4 * (Highway Fuel Consumption)) at 190 km/h.
#''Correction coefficient'' is used to correct every value of fuel consumption which is sent to the server through an expression of ((Used Fuel) * ''Correction coefficient''). By default it is 1, with minimum and maximum values of accordingly 0.01 and 2. For example, when correction coefficient is 1 and {{{model|FMB1YX}}} calculates that the amount of used fuel over 35 m distance is 20 ml, the value of 20 ml will be sent to the server, and if correction coefficient is 1.2, the value of 20 * 1.2 = 24 ml will be sent to the server.
+
#'' Correction coefficient'' is used to correct every value of fuel consumption which is sent to the server through an expression of ((Used Fuel) * ''Correction coefficient''). By default, it is 1, with minimum and maximum values of accordingly 0.01 and 2. For example, when correction coefficient is 1 and {{{model|FMB1YX}}} calculates that the amount of used fuel over 35 m distance is 20 ml, the value of 20 ml will be sent to the server, and if correction coefficient is 1.2, the value of 20 * 1.2 = 24 ml will be sent to the server.
#''Fuel Consumption on Idling'' is used to calculate fuel consumption when ignition is on, but the vehicle is stationary. The consumption value is 1 l/h by default, with minimum and maximum of accordingly 0 and 5 l/h. This parameter is less than 1.0 l/h for almost all diesel cars and is equal to about 1.5 – 2.0 l/h for gasoline cars.
+
#'' Fuel Consumption on Idling'' is used to calculate fuel consumption when the ignition is on, but the vehicle is stationary. The consumption value is 1 l/h by default, with the minimum and maximum of accordingly 0 and 5 l/h. This parameter is less than 1.0 l/h for almost all diesel cars and is equal to about 1.5 – 2.0 l/h for gasoline cars.
    
{{{dout_control_via_ignition_feature|==DOUT Control Via Ignition==
 
{{{dout_control_via_ignition_feature|==DOUT Control Via Ignition==
Line 100: Line 100:  
[[Image:DOUT Control via Ignition.png|{{{dout_control_via_ignition|size}}}|right]]
 
[[Image:DOUT Control via Ignition.png|{{{dout_control_via_ignition|size}}}|right]]
   −
This feature allows direct control of DOUT by configured ignition source status. When enabled, the function will start to monitor ignition status, and once the ignition changes state from On to Off after configured Ignition Off timeout, selected DOUT (Digital Output) will be turned On.<br/><br/>
+
This feature allows direct control of DOUT by configured ignition source status. When enabled, the function will start to monitor ignition status, and once the ignition changes state from On to Off after configured Ignition Off a timeout, selected DOUT (Digital Output) will be turned On.<br/><br/>
    
Turning DOUT Off is possible with enough voltage applied to the configured DIN (Digital Input). Voltage requirements: DIN1 – 7.5V, DIN2-4 – 2.5V.<br/><br/>
 
Turning DOUT Off is possible with enough voltage applied to the configured DIN (Digital Input). Voltage requirements: DIN1 – 7.5V, DIN2-4 – 2.5V.<br/><br/>

Navigation menu