Jump to content
  • EN

Template:FTX First Start: Difference between revisions

From Teltonika Telematics Wiki
← Older edit
VisualWikitext
No edit summary
 
(191 intermediate revisions by 5 users not shown)
Line 1: Line 1:
<b>
<b>
{{#switch: {{{model|FTC881}}}
{{#switch: {{{model}}}
| FTC881 = Small and smart waterproof tracker
| FTC881 = Next-generation high voltage 4G LTE Cat 1 battery-mounted vehicle GPS tracker with enhanced GNSS accuracy and IP69K resistance.
| FTC921 = Small and smart tracker
| FTC921 = Next-generation high voltage 4G LTE Cat 1 vehicle GPS tracker with enhanced GNSS accuracy.
| FTC961 = Small and smart waterproof tracker
| FTC961 = Next-generation high voltage 4G LTE Cat 1 vehicle GPS tracker with enhanced GNSS accuracy and IP69K resistance.
| FTC305 = Small 4G LTE (CAT 1) tracker for e-bikes, e-scooters and e-forklifts with CAN interface and 10-97 V power supply range
| FTC305 = Small 4G LTE (CAT 1) tracker for e-bikes, e-scooters and e-forklifts with CAN interface and 10-97 V power supply range
| FTM305 = Small 4G LTE (CAT M1) tracker for e-bikes, e-scooters and e-forklifts with CAN interface and 10-97 V power supply range
| FTM305 = Small 4G LTE (CAT M1) tracker for e-bikes, e-scooters and e-forklifts with CAN interface and 10-97 V power supply range
| #default = Small and smart tracker
}}
}}
</b>
</b>
Line 12: Line 11:
<!-- If model has more than 1 case version, show more images -->
<!-- If model has more than 1 case version, show more images -->
{{#switch: {{{model}}}
{{#switch: {{{model}}}
| #default =  <!-- Default case, show 1 image for all other models -->
[[Image:{{{model}}} side.png|thumb|400x300px|right|upright=0.35|{{{model}}}]]
| FTC305 =
| FTC305 =
[[Image:{{{model|FTC881}}} casing side.png|thumb|400x300px|right|upright=0.35|{{{model|FTC881}}} casing version]]
[[Image:{{{model}}} casing side.png|thumb|400x300px|right|upright=0.35|{{{model}}} casing version]]
[[Image:{{{model|FTC881}}} no-casing side.png|thumb|400x300px|right|upright=0.35|{{{model|FTC881}}} no-casing version]]
[[Image:{{{model}}} no-casing side.png|thumb|400x300px|right|upright=0.35|{{{model}}} no-casing version]]
| #default =  <!-- Default case, show 1 image for all other models -->
[[Image:{{{model|FTC881}}} side.png|thumb|400x300px|right|upright=0.35|{{{model|FTC881}}}]]
}}
}}
<br>
<br>
Line 23: Line 24:
<!-- If model has more than 1 case version, show a bigger image -->
<!-- If model has more than 1 case version, show a bigger image -->
{{#switch: {{{model}}}
{{#switch: {{{model}}}
| #default =  <!-- Default case, show a smaller picture for all other models -->
[[Image:{{{model}}} know your device.png|400px]]
| FTC305 =
| FTC305 =
[[Image:{{{model|FTC881}}} know your device.png|centre|1000 px]]
[[Image:{{{model}}} know your device.png|centre|1000px]]
| #default = <!-- Default case, show a smaller picture for all other models -->
 
[[Image:{{{model|FTC881}}} know your device.png|400px]]
| FTC887
| FTM887 =
[[Image:{{{model}}} know your device.png|centre|1000px]]
 
|FTM880
|FTC880
|FTC921
|FTC961 =
[[Image:{{{model}}} know your device.png|centre|1000px]]
 
| FTC134
| FTM134 =
[[Image:{{{model}}} know your device.png|centre|1000px]]
 
| ATC700
| ATM700 =  
[[Image:{{{model}}} know your device.png|centre|1000px]]
 
| FTM927 =
[[Image:{{{model}}} know your device.png|centre|750px]]
 
| FTC164 =
[[File:{{{model}}} know your device.png|centre|750px]]
}}
}}


=='''SET UP YOUR DEVICE'''==
=='''SET UP YOUR DEVICE'''==
 
{{#switch: {{{model}}}
| #default = <!-- Default case for devices with external power -->
<table class="wikitable" style="background-color: white;">
<table class="wikitable" style="background-color: white;">
<tr>
<tr>
Line 38: Line 64:
</table>
</table>


{{#switch: {{{model|FTC881}}}
| ATM704
| ATC704
| ATM700
| ATC700 = <!-- For devices without external power -->
<table class="wikitable" style="background-color: white;">
<tr>
<td> [[Image:Alert.png|center|50px]] </td>
<td> <b> Physical SIM card insertion/removal must be performed when device is powered off. Otherwise, the SIM card might be damaged or device will not detect it.</b> </td>
</tr>
</table>
<table class="wikitable" style="background-color: white;">
<tr>
<td> [[Image:Alert.png|center|50px]] </td>
<td> <b> The asset tracker enclosure fits tightly. It has four locking clips that may require firm, individual pressure to snap into place. This applies only to the pilot batch and will be improved in future production.</b> </td>
</tr>
</table>
}}


| FTC881 =  
<!-- If model has more than 1 case version, show more images -->
# Device is delivered partly closed. Gently remove {{{model|FTC881}}} '''cover'''.
{{#switch: {{{model}}}
# Insert '''SIM''' card as shown. Make sure that SIM card '''cut-off corner''' is pointing towards SIM slot.
| #default = <!-- Default case, show 1 picture for all other models -->
# Battery is already connected, so after configuring device fully close casing.
[[Image:{{{model}}} setup.png|1000px|left]]
# Device is ready to be mounted.
<div style="clear:left;"></div>
 
| FTC305 =
[[Image:FTC881 setup.png|850px]]
'''{{{model}}} CASING VERSION'''<br>
[[Image:{{{model}}}_casing_setup.png|1000px|left]]
<div style="clear:left;"></div>
'''{{{model}}} NO-CASING VERSION'''
[[Image:{{{model}}}_no-casing_setup.png|1000px|left]]
<div style="clear:left;"></div>


| FTC921 =  
|FTC921=
# Gently remove {{{model|FTC921}}} '''cover''' using '''plastic pry tool''' from one side.
[[Image:{{{model}}}_setup.png|1000px]]<br>
# Gently remove {{{model|FTC921}}} '''cover''' using '''plastic pry tool''' from another side.
# Insert '''SIM''' card as shown. Make sure that SIM card '''cut-off corner''' is pointing forward to slot.
# Connect the battery as shown on device. Position the battery in place where it does not obstruct other components.
# Attach device '''cover''' back. Device is ready to be connected.


[[Image:FTC921_setup1.png|850px]]
|FTC881
[[Image:FTC921_setup2.png|550px]]
|FTM880
|FTC880
|FTC961 =
[[Image:{{{model}}}_setup.png|1000px]]<br>


| FTC961 =
|FTC134
# Device is delivered partly closed. Gently remove {{{model|FTC961}}} '''cover'''.
|FTM134 =  
# Insert '''SIM''' card as shown. Make sure that SIM card '''cut-off corner''' is pointing towards SIM slot.
[[Image:{{{model}}}_setup.png|1000px]]<br>
# Battery is already connected, so after configuring device fully close casing.
# Device is ready to be mounted.


[[Image:FTC881_setup.png|850px]]
|ATC700
|ATM700 =
[[Image:{{{model}}}_setup.png|1000px]]<br>


| FTC305 =
}}
'''FTC305 CASING VERSION'''
# Insert '''SIM''' card as shown with PIN request disabled. Make sure that SIM card '''cut-off corner''' is pointing towards the SIM slot.
# Connect the main 7-pin cable connector to the socket on PCB.
# Attach the cover. '''Please note:''' Before attaching cover, ensure the device is configured via USB. The USB port on the PCB will be inaccessible once the cover is fully attached.
# Device is ready to be mounted.


[[Image:FTC305_casing_setup.png|850px]]
{{#switch: {{{model}}}
| #default = <!-- Default case, show 1 picture for all other models -->


'''FTC305 NO-CASING VERSION'''
== '''HOW TO REMOVE COVER''' ==
# You will receive your device with thermal cambric covering the PCB. Remove the thermal cambric.
# Insert '''SIM''' card as shown with PIN request disabled. Make sure that SIM card '''cut-off corner''' is pointing towards the SIM slot.
# Connect the main 7-pin cable connector to the socket on PCB.
# Re-attach thermal cambric. '''Please note:''' You can heat the thermal cambric for it to fully seal the PCB, however, after heating it, you will no longer be able to access SIM and USB slots unless the cambric is removed. You will still be able to configure the device using FOTA WEB or Bluetooth.
# External GNSS and Cellular antennas are included in the packaging box. Connect the GNSS antenna to adapter that is connected to PCB. Then connect the Cellular antenna to LTE adapter that is connected to PCB.
#  External battery is included in the packaging box. Connect the battery to battery adapter that is connected to PCB.
# Device is ready to be mounted.


[[Image:FTC305_no-casing_setup.png|850px]]
<table class="wikitable" style="background-color: white;">
<tr>
<td> [[Image:Alert.png|center|50px]] </td>
<td> <b> Device casing is designed to be water-proof and match requirements for IP69K. Please note that once the cover is fully clipped it will require additional plastic pry tools to be opened! Please make sure to review short walkthrough video for more details:</b></td>
</tr>
</table>
<youtube>https://www.youtube.com/watch?v=fgOQtk6X0nw</youtube>
| FTC134
| FTC305
| FTM305 =


| FTM305 =  
| ATM704
# Insert '''SIM''' card as shown with PIN request disabled. Make sure that SIM card '''cut-off corner''' is pointing towards the SIM slot.
| ATC704
# Connect the main 7-pin cable connector to the socket on PCB.
| ATM700
# Attach the cover. '''Please note:''' Before attaching cover, ensure the device is configured via USB. The USB port on the PCB will be inaccessible once the cover is fully attached.
| ATC700 = <!-- Case for ATx devices with IP68 Rating -->
# Device is ready to be mounted.
== '''HOW TO REMOVE COVER''' ==
[[Image:FTM305_setup.png|850px]]
<table class="wikitable" style="background-color: white;">
<tr>
<td> [[Image:Alert.png|center|50px]] </td>
<td> <b> Device casing is designed to be water-proof and match requirements for IP68. Please note that once the cover is fully clipped it will require additional plastic pry tools to be opened!</b></td>
</tr>
</table>
}}
}}


{{#switch: {{{model}}}
| #default =  <!-- Default value for devices with pinouts -->
=='''PINOUT'''==
=='''PINOUT'''==
<table class="nd-othertables_2" style="width:80%; margin-bottom: 30px;">
<table class="nd-othertables_2" style="width:80%; margin-bottom: 30px;">
     <tr>
     <tr>
Line 102: Line 153:
         <th style="width:20%; text-align: left;">DESCRIPTION</th>
         <th style="width:20%; text-align: left;">DESCRIPTION</th>
         <th rowspan="13" style="width:30%; text-align: center; vertical-align: middle;">
         <th rowspan="13" style="width:30%; text-align: center; vertical-align: middle;">
             [[Image:{{{model|FTC881}}}_pinout.png|400px|center]]
             [[Image:{{{model}}}_pinout.png|400px|center]]
         </th>
         </th>
| ATM704
| ATC704
| ATM700
| ATC700 =
}}
{{#switch: {{{model}}}


{{#switch: {{{model|FTC881}}}
| FTM887
 
| FTC887
| FTC881 =
| FTC880
    <tr>
| FTM880 =  
<tr>
         <td style="text-align: left;">1</td>
         <td style="text-align: left;">1</td>
         <td style="text-align: left; color:#FF0000;"><strong>VCC</strong></td>
         <td style="text-align: left; color:#FF0000;"><strong>VCC</strong></td>
         <td style="text-align: left;">(Red) Power supply (+10-90 V DC) (+).</td>
         <td style="text-align: left;">(Red) Power supply (+10-30 V DC) (+).</td>
     </tr>
     </tr>
     <tr>
     <tr>
Line 120: Line 178:
</table>
</table>


| FTC921
| FTC881 =
| FTC961 =
    <tr>
        <td style="text-align: left;">1</td>
        <td style="text-align: left; color:#FF0000;"><strong>VCC</strong></td>
        <td style="text-align: left;">(Red) Power supply (+10-90 V DC) (+).</td>
    </tr>
    <tr>
        <td style="text-align: left;">2</td>
        <td style="text-align: left; color:#000000;"><strong>GND</strong></td>
        <td style="text-align: left;">(Black) Ground (-).</td>
    </tr>
</table>
 
| FTC921
| FTC961  
| FTC965 =
     <tr>
     <tr>
         <td style="text-align: left;">1</td>
         <td style="text-align: left;">1</td>
Line 149: Line 221:
</table>
</table>


| FTC305
| FTC920
| FTM305 =
| FTC924
| FTC927
| FTM927 =
     <tr>
     <tr>
         <td style="text-align: left;">1</td>
         <td style="text-align: left;">1</td>
         <td style="text-align: left; color:#FF0000;"><strong>VCC</strong></td>
         <td style="text-align: left; color:#FF0000;"><strong>VCC</strong></td>
         <td style="text-align: left;">(Red) Power supply (+10-97 V DC) (+).</td>
         <td style="text-align: left;">(Red) Power supply (+10-30 V DC) (+).</td>
     </tr>
     </tr>
     <tr>
     <tr>
Line 163: Line 237:
     <tr>
     <tr>
         <td style="text-align: left;">3</td>
         <td style="text-align: left;">3</td>
         <td style="text-align: left; color:#FFD700;"><strong>DIN1 / AIN1 / 1-W</strong></td>
         <td style="text-align: left; color:#FFD700;"><strong>DIN1</strong></td>
         <td style="text-align: left;">(Yellow) Digital input channel 1 / Analog input channel 1 / Data channel for 1-Wire devices.</td>
         <td style="text-align: left;">(Yellow) Digital input, channel 1. DEDICATED FOR IGNITION INPUT Input range: 7.5-30 V DC.</td>
     </tr>
     </tr>
     <tr>
     <tr>
         <td style="text-align: left;">4</td>
         <td style="text-align: left;">4</td>
         <td style="text-align: left; color:#808080;"><strong>DOUT1</strong></td>
         <td style="text-align: left; color:#808080;"><strong>DIN 2/AIN 1/DGS</strong></td>
         <td style="text-align: left;">(Grey) Digital output, channel 1.</td>
         <td style="text-align: left;">(Grey) Input range: 0-30 V DC / Digital input,
channel 2 / GND Sense input
     </tr>
     </tr>
     <tr>
     <tr>
         <td style="text-align: left;">5</td>
         <td style="text-align: left;">5</td>
         <td style="text-align: left; color:#E0E0E0;"><strong>DOUT2</strong></td>
        <td style="text-align: left; color:#E0E0E0;"><strong>DOUT1</strong></td>
         <td style="text-align: left;">(White) Digital output, channel 2.</td>
        <td style="text-align: left;">(White) Digital output. Open collector output. Max. 0,5 A DC.</td>
    </tr>
</table>
 
| FTC305
| FTM305 =
    <tr>
        <td style="text-align: left;">1</td>
        <td style="text-align: left; color:#FF0000;"><strong>VCC</strong></td>
        <td style="text-align: left;">(Red) Power supply (+10-97 V DC) (+).</td>
    </tr>
    <tr>
        <td style="text-align: left;">2</td>
        <td style="text-align: left; color:#000000;"><strong>GND</strong></td>
        <td style="text-align: left;">(Black) Ground (-).</td>
    </tr>
    <tr>
        <td style="text-align: left;">3</td>
        <td style="text-align: left; color:#FFD700;"><strong>DIN1 / AIN1 / 1-W</strong></td>
        <td style="text-align: left;">(Yellow) Digital input channel 1 / Analog input channel 1 / Data channel for 1-Wire devices.<br>'''Note: AIN1 / 1-Wire only available from 3.7.x. firmware version.'''</td>
    </tr>
    <tr>
        <td style="text-align: left;">4</td>
        <td style="text-align: left; color:#808080;"><strong>DOUT1</strong></td>
        <td style="text-align: left;">(Grey) Digital output, channel 1.</td>
    </tr>
    <tr>
        <td style="text-align: left;">5</td>
         <td style="text-align: left; color:#E0E0E0;"><strong>DOUT2</strong></td>
         <td style="text-align: left;">(White) Digital output, channel 2.</td>
     </tr>
     </tr>
     <tr>
     <tr>
Line 188: Line 292:
</table>
</table>


}}
| FTM134
 
| FTC134 =
=='''PC CONNECTION (WINDOWS)'''==
<tr>
 
        <td style="text-align: left;">1</td>
{{#switch: {{{model|FTC881}}}
        <td style="text-align: left; color:#FF0000;"><strong>VCC</strong></td>
 
        <td style="text-align: left;">(Red) Power supply (+8-32V V DC) (+).</td>
| FTC881
    </tr>
| FTC921
    <tr>
| FTC961 =
         <td style="text-align: left;">2</td>
# Power-up {{{model|FTC881}}} with DC voltage (10-90V) power supply using power wires. LEDs should start blinking, see "[[#LED_behaviour_description|'''LED BEHAVIOUR DESCRIPTION''']]".
         <td style="text-align: left; color:#5e5e5e;"><strong>DOUT3</strong></td>
# Connect device to computer using USB Type-C cable and install USB driver, see "[[#How to install USB drivers (Windows)|'''HOW TO INSTALL USB DRIVERS (WINDOWS)''']]".
         <td style="text-align: left;">(Grey) Digital output channel 3.</td>
| FTC305
| FTM305 =
# Connect device to computer using USB Type-C cable. <br> <b>Please note:</b> {{{model}}} device does not require an external power supply for configuration. However, without external power, data sending and other cellular connectivity functions will not work. If you want to test the device on a table, it is advised to power up {{{model}}} with a DC voltage (10-97V) power supply using power wires.
# Install USB driver, see "[[#How to install USB drivers (Windows)|'''HOW TO INSTALL USB DRIVERS (WINDOWS)''']]".
 
}}
 
=='''HOW TO INSTALL USB DRIVERS (WINDOWS)'''==
 
# Please download COM port drivers from '''[[Media:TeltonikaCOMDriver.zip|here]]'''.
# Extract and run '''TeltonikaCOMDriver.exe'''.
# Click '''Next''' in driver installation window.
# In the following window click '''Install''' button.
# Setup will continue installing the driver and eventually the confirmation window will appear. Click '''Finish''' to complete the setup.
 
=='''CONFIGURATION (WINDOWS)'''==
 
Most Teltonika devices are shipped with default factory settings. Use [https://wiki.teltonika-gps.com/view/Telematics_Configuration_Tool_(TCT) Telematics Configuration Tool (TCT)] to change these settings according to your needs.
 
<table class="nd-othertables_2" style="width:60%;">
<tr>
         <th rowspan="1" style="width:30%; vertical-align: middle; text-align: left;"></th>
         <th rowspan="1" style="width:30%; vertical-align: middle; text-align: left;">Configurator</th>
         <th rowspan="1" style="width:40%; vertical-align: middle; text-align: left;">TCT</th>
     </tr>
     </tr>
<tr>
    <tr>
         <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Operating system</th>
         <td style="text-align: left;">3</td>
         <td style="vertical-align: middle; text-align: left; ">Windows 7<br>Windows 8.1<br>Windows 10<br>Windows 11</td>
        <td style="text-align: left; color:#cecece;"><strong>DIN3/AIN3</strong></td>
         <td style="vertical-align: middle; text-align: left; ">Windows 10<br>Windows 11</td>
        <td style="text-align: left;">(White) Digital input channel 3 / Analog input channel 3.</td>
    </tr>
    <tr>
         <td style="text-align: left;">4</td>
        <td style="text-align: left; color:#009e5e;"><strong>DIN4/AI</strong><span style="color:#cecece;"><strong>N4/DGS</strong></span></td>
         <td style="text-align: left;">(White/Green) Digital input channel 4 / Ground sense / Analog input channel 4.</td>
    </tr>
    <tr>
        <td style="text-align: left;">5</td>
        <td style="text-align: left; color:#ffde3b;"><strong>DIN1/AIN1</strong></td>
        <td style="text-align: left;">(Yellow) Digital input 1 / Analog input 1.</td>
     </tr>
     </tr>
<tr>
    <tr>
         <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">MS .NET Framework
         <td style="text-align: left;">6</td>
version</th>
         <td style="text-align: left; color:#1355b7;"><strong>INP</strong><span style="color:#cecece;"><strong>UT6</strong></span></td>
         <td style="vertical-align: middle; text-align: left;">MS .NET
         <td style="text-align: left;">(White/Blue) TX EXT (LVCAN – TX).</td>
framework 5.0</td>
         <td style="vertical-align: middle; text-align: left; ">MS .NET framework 6.0</td>
     </tr>
     </tr>
<tr>
    <tr>
         <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Version</th>
         <td style="text-align: left;">7</td>
         <td style="vertical-align: middle; text-align: left;">64 bit</td>
         <td style="text-align: left; color:#000000;"><strong>GND</strong></td>
         <td style="vertical-align: middle; text-align: left; ">64 bit</td>
         <td style="text-align: left;">(Black) Ground (-).</td>
     </tr>
     </tr>
  <tr>
    <tr>
         <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Disk Storage</th>
         <td style="text-align: left;">8</td>
         <td style="vertical-align: middle; text-align: left;"></td>
         <td style="text-align: left; color:#ff4e26;"><strong>DOU</strong><span style="color:#cecece;"><strong>T1</strong></span></td>
         <td style="vertical-align: middle; text-align: left; ">1 GB of free disk space
         <td style="text-align: left;">(White/Orange) Digital output channel 1.</td>
</td>
     </tr>
     </tr>
     <tr>
     <tr>
         <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Internet</th>
         <td style="text-align: left;">9</td>
         <td style="vertical-align: middle; text-align: left;"></td>
         <td style="text-align: left; color:#46007c;"><strong>DOUT2</strong></td>
         <td style="vertical-align: middle; text-align: left; ">Ethernet port or Wi-Fi w/ network access for auto-update</td>
         <td style="text-align: left;">(Purple) Digital output channel 2.</td>
     </tr>
     </tr>
</table>
    <tr>
        <td style="text-align: left;">10</td>
        <td style="text-align: left; color:#1355b7;"><strong>1WIRE POWER</strong></td>
        <td style="text-align: left;">(Blue) +3.8 V output for 1-Wire devices.</td>
    </tr>
    <tr>
        <td style="text-align: left;">11</td>
        <td style="text-align: left; color:#009e5e;"><strong>DIN2/AIN2/1WIRE DATA</strong></td>
        <td style="text-align: left;">(Green) Digital input channel 2 / Analog input 2 / Data for 1-Wire devices.</td>
    </tr>
    <tr>
        <td style="text-align: left;">12</td>
        <td style="text-align: left; color:#ffde3b;"><strong>INP</strong><span style="color:#cecece;"><strong>UT5</strong></span></td>
        <td style="text-align: left;">(White/Yellow) RX EXT (LVCAN – RX).</td>
    </tr>
</table>


===TCT===
| FTC164
| FTM164 =


<!-- Switch for specific TCT evaluation key if needed -->
<tr>
{{#switch: {{{model|FTC881}}}
        <td style="text-align: left;">1</td>
| FTC305
        <td style="text-align: left; color:#FF0000;"><strong>VCC</strong></td>
| FTM305 =
        <td style="text-align: left;">(Red) Power supply (+8-32V V DC) (+).</td>
<ol>
    </tr>
<li>Download the TCT (compressed archive).</li>
    <tr>
<li>Extract the archive and launch the executable. The TCT will be installed.</li>
        <td style="text-align: left;">2</td>
<li>Launch the TCT.</li>
        <td style="text-align: left; color:#000000;"><strong>GND</strong></td>
<li>Go to '''Settings''' -> '''User keys''', then copy and paste the full key text in '''Add new key''' field:<br>
        <td style="text-align: left;">(Black) Ground (-).</td>
<pre style="margin-left: 0px;">
    </tr>
BEGIN TCT KEY
        <td style="text-align: left;">3</td>
  type:       ExpFWKey
        <td style="text-align: left; color:#ffde3b;"><strong>DIN1/AIN1</strong></td>
  description: FTx305 with develop version firmware
        <td style="text-align: left;">(Yellow) Digital input 1 / Analog input 1.</td>
  key:         7394b05f-f32a-4648-bd03-d61e7dfd0175
    </tr>
  expires:     2025-06-30
    <tr>
  signature:   v1|Gr108NPI3QiXElpAEIZMtAvfc9l8EI0apf/yvXyShjhiEFh4jPh9auTJg0K4RLZfJXkF9bhm3s93aMjiXsKDeldi21YSnLxY1oaCRhQGowPQcxcTmZv74OMwX5gf5qZG2hbLdKQEpg3bis1lZNnBDphYtG2eqPiiPgSaBmgAfU01cMpdXahLhruOZFVqQC5hWkPiVRCmcf2Cez7aXW8Vji5hGCTqmzVkbsl+/ZsMSnKyZfbYCL8QwzbLtAFdmI0XWXVFtyBXAIgSJeqbrsHOgtQDB8e34zbBn3IzY0GhYqTKMc20Dt9jDn8VBhsCIXlK4zNua3j2vnyHXpF8rl5UJA==
        <td style="text-align: left;">4</td>
END TCT KEY
        <td style="text-align: left; color:#009e5e;"><strong>DIN2/AIN2/1WIRE</strong></span></td>
</pre>
        <td style="text-align: left;">(Green) Digital input channel 2 / Analog input channel 2 / 1-WIRE.</td>
'''Note:''' This TCT key will expire on '''2025-06-30'''. Please contact us via HelpDesk to receive a new one before the expiration date.<br>
    </tr>
<br>[[Image:FTX305 TCT key.png|1000px]]
    <tr>
</li>
        <td style="text-align: left;">5</td>
</ol>
        <td style="text-align: left; color:#FF0000;"><strong>DIN3/</strong><span style="color:#cecece;"><strong>AIN3</strong></span></td>
<ol start="5">
         <td style="text-align: left;">(Red/White) Digital input channel 3 / Ground sense / Analog input channel 3.</td>
<li>In the Discovered devices list, select your device and press '''Configure'''.</li>
     </tr>
<li>The Device status window opens. It contains device, GNSS, and Cellular information.[[Image:FTX device status.png]]<br>[[Image:FTX buttons.png|left|120px]]
<tr>
Save to device – saves configuration to device.<br><br>
        <td style="text-align: left;">6</td>
Upload file – loads configuration from file.<br><br>
        <td style="text-align: left; color:#009e5e;"><strong>DIN4/AI</strong><span style="color:#cecece;"><strong>N4/DGS</strong></span></td>
Save to file – saves configuration to file.<br><br>
        <td style="text-align: left;">(White/Green) Digital input channel 4 / Ground sense / Analog input channel 4.</td>
Update – update device firmware.<br><br>
    </tr>
Reset configuration – sets device configuration to default.<br><br>
    <tr>
<br>
        <td style="text-align: left;">7</td>
Most important configuration sections are [https://wiki.teltonika-gps.com/view/{{{model|FTC305}}}_Mobile_network Mobile network] (Server, Mobile network settings) and [https://wiki.teltonika-gps.com/view/{{{model|FTC305}}}_Tracking_settings Tracking settings] (data collection parameters). More details about {{{model|FTC305}}} configuration using TCT can be found [https://wiki.teltonika-gps.com/view/{{{model|FTC305}}}_Configuration here].
        <td style="text-align: left; color:#1355b7;"><strong>DIN5/</strong><span style="color:#cecece;"><strong>AIN5</strong></span></td>
</li>
        <td style="text-align: left;">(White/Blue)  Digital input channel 5 / Ground sense / Analog input channel 5.</td>
</ol>
    </tr>
    <tr>
        <td style="text-align: left;">8</td>
        <td style="text-align: left; color:#1355b7;"><strong>1WIRE POWER</strong></td>
        <td style="text-align: left;">(Blue) +3.8 V output for 1-Wire devices.</td>
    <tr>
        <td style="text-align: left;">9</td>
        <td style="text-align: left; color:#ff4e26;"><strong>DOU</strong><span style="color:#cecece;"><strong>T1</strong></span></td>
        <td style="text-align: left;">(White/Orange) Digital output channel 1.</td>
    </tr>
    <tr>
        <td style="text-align: left;">10</td>
        <td style="text-align: left; color:#46007c;"><strong>DOUT2</strong></td>
        <td style="text-align: left;">(Dark Grey) Digital output channel 2.</td>
    </tr>
    <tr>
        <td style="text-align: left;">11</td>
        <td style="text-align: left; color:#5A5A5A;"><strong>DOU<span style="color:#cecece;"><strong>T3</strong></td>
        <td style="text-align: left;">(Black/White) Digital output channel 3.</td>
    </tr>
    <tr>
        <td style="text-align: left;">12</td>
        <td style="text-align: left; color:#cecece;"><strong>DOUT4</td>
        <td style="text-align: left;">(Light Grey) Digital output channel 4 .</td>
    </tr>
</table>


| #default = <!-- Default case, model does not use TCT evaluation key -->
}}
# Download the TCT (compressed archive).
# Extract the archive and launch the executable. The TCT will be installed.
# Launch the TCT.
# In the Discovered devices list, select your device and press '''Configure'''.
# The Device status window opens. It contains device, GNSS and Cellular information.[[Image:FTX device status.png]]<br>[[Image:FTX buttons.png|left|120px]]
Save to device – saves configuration to device.<br><br>
Upload file – loads configuration from file.<br><br>
Save to file – saves configuration to file.<br><br>
Update – update device firmware.<br><br>
Reset configuration – sets device configuration to default.<br><br>
<br>
Most important configuration sections are [https://wiki.teltonika-gps.com/view/{{{model|FTC881}}}_Mobile_network Mobile network] (Server, Mobile network settings) and [https://wiki.teltonika-gps.com/view/{{{model|FTC881}}}_Tracking_settings Tracking settings] (data collection parameters). More details about {{{model|FTC881}}} configuration using TCT can be found [https://wiki.teltonika-gps.com/view/{{{model|FTC881}}}_Configuration here].


=='''QUICK SMS CONFIGURATION'''==
=='''PC CONNECTION (WINDOWS)'''==
The default configuration ensures best track quality and optimal data usage.<br>


Quickly set up your device by sending this SMS command to it: <br>
{{#switch: {{{model}}}


[[Image:FTX quick sms configuration.png|left|800px]]
| FTC881
<div style="clear:left;"></div>
| FTC921
| FTC961 =
# Power-up {{{model}}} with DC voltage (10-90V) power supply using power wires. LEDs should start blinking, see "[[#LED_behaviour_description|'''LED BEHAVIOUR DESCRIPTION''']]".
# Connect device to computer using USB Type-C cable and install USB driver, see "[[#How to install USB drivers (Windows)|'''HOW TO INSTALL USB DRIVERS (WINDOWS)''']]".


=='''DEFAULT CONFIGURATION SETTINGS'''==
| FTC920
[[Image:FTX default configuration settings.png|left|800px]]
| FTC924
<div style="clear:left;"></div>
| FTC927 =
# Power-up {{{model}}} with DC voltage (10-30V) power supply using power wires. LEDs should start blinking, see "[[#LED_behaviour_description|'''LED BEHAVIOUR DESCRIPTION''']]".
# Connect device to computer using USB Type-C cable and install USB driver, see "[[#How to install USB drivers (Windows)|'''HOW TO INSTALL USB DRIVERS (WINDOWS)''']]".
 
| ATM704
| ATC704
| ATM700
| ATC700 =
# Connect device to computer using USB Type-C cable. <br>
# Install USB driver, see "[[#How to install USB drivers (Windows)|'''HOW TO INSTALL USB DRIVERS (WINDOWS)''']]".


After successful SMS configuration, {{{model|FTC881}}} device will synchronize time and update records to configured server. Time
| FTC305
intervals and default I/O elements can be changed by using [https://wiki.teltonika-gps.com/view/{{{model|FTC881}}}_Configuration TCT] or [https://wiki.teltonika-gps.com/view/{{{model|FTC881}}}_Parameter_list Parameter list].
| FTM305 =
}}
# Connect device to computer using USB Type-C cable. <br> <b>Please note:</b> {{{model}}} device does not require an external power supply for configuration. However, without external power, data sending and other cellular connectivity functions will not work. If you want to test the device on a table, it is advised to power up {{{model}}} with a DC voltage (10-97V) power supply using power wires.
# Install USB driver, see "[[#How to install USB drivers (Windows)|'''HOW TO INSTALL USB DRIVERS (WINDOWS)''']]".


=='''MOUNTING RECOMMENDATIONS'''==
| FTM880 =  
# Connect device to computer using USB Type-C cable. <br> <b>Please note:</b> {{{model}}} device does not require an external power supply for configuration. However, without external power, data sending and other cellular connectivity functions will not work. If you want to test the device on a table, it is advised to power up {{{model}}} with a DC voltage (10-30V) power supply using power wires.
# Install USB driver, see "[[#How to install USB drivers (Windows)|'''HOW TO INSTALL USB DRIVERS (WINDOWS)''']]".


{{#switch: {{{model|FTC881}}}
| FTC880 =
| FTC881 =
# Connect device to computer using USB Type-C cable. <br> <b>Please note:</b> {{{model}}} device does not require an external power supply for configuration. However, without external power, data sending and other cellular connectivity functions will not work. If you want to test the device on a table, it is advised to power up {{{model}}} with a DC voltage (10-30V) power supply using power wires.
'''DEVICE FASTENING'''
# Install USB driver, see "[[#How to install USB drivers (Windows)|'''HOW TO INSTALL USB DRIVERS (WINDOWS)''']]".


* Locate the battery in your vehicle. If present remove the battery cover to access the battery.
| FTM134
*  There is a double sided tape on the back of the device, use it to attach the device on the battery, so that the GNSS antenna and LEDs indicators are facing up.
| FTC134 =
# Power-up {{{model}}} with DC voltage (8-32 V) power supply using power wires. LEDs should start blinking, see "[[#LED_behaviour_description|'''LED BEHAVIOUR DESCRIPTION''']]".
# Connect device to computer using USB Type-C cable and install USB driver, see "[[#How to install USB drivers (Windows)|'''HOW TO INSTALL USB DRIVERS (WINDOWS)''']]".
}}


'''CONNECTING POWER SOURCE'''
=='''HOW TO INSTALL USB DRIVERS (WINDOWS)'''==


*  Device power wire is designed to be directly connected to the positive terminal fastener of the vehicle battery.
# Please download COM port drivers from '''[[Media:TeltonikaCOMDriver.zip|here]]'''.
# Extract and run '''TeltonikaCOMDriver.exe'''.
# Click '''Next''' in driver installation window.
# In the following window click '''Install''' button.
# Setup will continue installing the driver and eventually the confirmation window will appear. Click '''Finish''' to complete the setup.


'''CONNECTING GROUND WIRE'''
=='''CONFIGURATION (WINDOWS)'''==


*  Device ground wire is designed to be directly connected to the negative terminal fastener of the vehicle battery.
Most Teltonika devices are shipped with default factory settings. Use [https://wiki.teltonika-gps.com/view/Telematics_Configuration_Tool_(TCT) Telematics Configuration Tool (TCT)] to change these settings according to your needs.


| FTC921
<table class="nd-othertables_2" style="width:60%;">
| FTC961 =
<tr>
'''CONNECTING WIRES'''
        <th rowspan="1" style="width:30%; vertical-align: middle; text-align: left;"></th>
        <th rowspan="1" style="width:40%; vertical-align: middle; text-align: left;">TCT</th>
    </tr>
<tr>
        <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Operating system</th>
        <td style="vertical-align: middle; text-align: left; ">Windows 10<br>Windows 11</td>
    </tr>
<tr>
        <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">MS .NET Framework
version</th>
        <td style="vertical-align: middle; text-align: left; ">MS .NET framework 6.0</td>
    </tr>
<tr>
        <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Version</th>
        <td style="vertical-align: middle; text-align: left; ">64 bit</td>
    </tr>
  <tr>
        <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Disk Storage</th>
        <td style="vertical-align: middle; text-align: left; ">1 GB of free disk space
</td>
    </tr>
    <tr>
        <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Internet</th>
        <td style="vertical-align: middle; text-align: left; ">Ethernet port or Wi-Fi w/ network access for auto-update</td>
    </tr>
</table>


* Wires should be fastened to stable wires or other non-moving parts. Any heat emitting and/or moving objects should be kept away from the wires.
===TCT===
* There should be no exposed wires. If factory isolation was removed while connecting wires, the isolation material should be applied.
<!-- Switch for specific TCT evaluation key if needed -->
* If the wires are placed in the exterior or in places where they can be damaged or exposed to heat, humidity, dirt, etc., additional isolation should be applied and the wires should not be loose.<br />
{{#switch: {{{model}}}
* Wires cannot be connected to the board computers or control units.


'''CONNECTING POWER SOURCE'''
| #default = <!-- Default case, model does not use TCT evaluation key -->
# Download the TCT (compressed archive).
# Extract the archive and launch the executable. The TCT will be installed.
# Launch the TCT.
# In the Discovered devices list, select your device and press '''Configure'''.
# The Device status window opens. It contains device, GNSS and Cellular information.[[Image:FTX device status.png]]<br>[[Image:FTX buttons.png|left|120px]]
Save to device – saves configuration to device.<br><br>
Upload file – loads configuration from file.<br><br>
Save to file – saves configuration to file.<br><br>
Update – update device firmware.<br><br>
Reset configuration – sets device configuration to default.<br><br>
<br>
Most important configuration sections are [https://wiki.teltonika-gps.com/view/{{{model}}}_Mobile_network Mobile network] (Server, Mobile network settings) and [https://wiki.teltonika-gps.com/view/{{{model}}}_Tracking_settings Tracking settings] (data collection parameters). More details about {{{model}}} configuration using TCT can be found [https://wiki.teltonika-gps.com/view/{{{model}}}_Configuration here].


* Be sure that after the car computer goes to sleep mode, power might be still available on the power wires. Depending on car, this may happen in 5 to 30 minutes period.
| FTC881 =
* When module is connected, measure voltage again to make sure it did not decrease.
* It is recommended to connect to the main power cable in the fuse box.
* 3 A, 125 V external fuse shall be used.


'''CONNECTING GROUND WIRE'''
# Download the TCT (compressed archive).
 
# Extract the archive and launch the executable. The TCT will be installed.
* Ground wire is connected to the vehicle frame or metal parts that are fixed to the frame.
# Launch the TCT.
* If the wire is fixed with the bolt, the loop must be connected to the end of the wire.
# In the Discovered devices list, select your device and press '''Configure'''.
* For better contact scrub paint from the spot where loop is going to be connected.
# The Device status window opens. It contains device, GNSS and Cellular information.[[Image:{{{model}}} device status.png]]<br>[[Image:FTX buttons.png|left|120px]]
Save to device – saves configuration to device.<br><br>
Upload file – loads configuration from file.<br><br>
Save to file – saves configuration to file.<br><br>
Update – update device firmware.<br><br>
Reset configuration – sets device configuration to default.<br><br>
<br>
Most important configuration sections are [https://wiki.teltonika-gps.com/view/{{{model}}}_Mobile_network Mobile network] (Server, Mobile network settings) and [https://wiki.teltonika-gps.com/view/{{{model}}}_Tracking_settings Tracking settings] (data collection parameters). More details about {{{model}}} configuration using TCT can be found [https://wiki.teltonika-gps.com/view/{{{model}}}_Configuration here].


| FTC305
| ATC700
| FTM305 =
| ATM700 =  
'''CONNECTING WIRES'''
<ol>
 
<li>Download the TCT (compressed archive).</li>
* Wires should be fastened to the other wires or nonmoving parts. Do not place the wires near moving or heat-emitting objects.
<li>Extract the archive and launch the executable. The TCT will be installed.</li>
* All electrical connections must be properly isolated. No bare wires should be visible. Re-apply isolation to wires if you removed factory isolation during installation.
<li>Launch the TCT.</li>
* If the wires are placed in the exterior or in places where they can be damaged or exposed to heat, humidity, dirt, etc., additional isolation should be applied.
<li>Go to '''Settings''' -> '''User keys''', copy the <u>'''full key text from "BEGIN TCT KEY" to "END TCT KEY"'''</u> and paste in '''Add new key''' field, then press '''Add key''':<br>
 
<pre style="margin-left: 0px;">
'''CONNECTING POWER SOURCE'''
BEGIN TCT KEY
* Ensure that after the vehicle computer falls asleep, power is still available on chosen wire. Depending on vehicle, this may happen in 5 to 30 minutes period.
  description: ATx700 with development firmware
* When module is connected, measure voltage again to make sure it did not decrease.
  type:        ExpFWKey
* It is recommended to connect main power cable to the main battery of the vehicle.
  key:        196b94ad-b3e4-4ab2-b092-258cc8c5fdb9
 
  expires:    2026-11-01
'''CONNECTING IGNITION WIRE'''
  signature:  v1|NRRBW8v8SlMvI6ICGtZAobRukuFVE1SUQYgBdZxqQmqsypy7Hxy/dw7TTjA0y8i09dtTjxBapLZAESIUT1T1XF29/nvb5jtNsjQKdQ3uzYYL1tlulAZ5l09JxrvEA28+aJEIHl91RgEZt0cmXbt9U5uQq0Yudf/3RlzGvrdc1tU4GqgO+yAvaSNO99ERFxTjVpRtJknx+4666LxBMZlNeOBupMdFupPZmxLwcrF+EBPf3wiDJVNl2SLwKAOpx1bR0yx5Ofk2zVfeRGO8OwifzcDDiUjBRw2vwFULbn6jjVEGCDOXqV84zqy0SE/ClLjJ1+7Alk49KR+nS+qCQKT+Fw==
 
END TCT KEY
* Make sure that you have selected the correct wire for ignition signal - the electrical signal from the wire should be present after starting the engine.
</pre>
* Check if this is not an ACC wire (when key is in the first position, most of the vehicle electronics are ON).
'''Note:''' This TCT key will expire on 2026-11-01. Please contact us via HelpDesk to receive a new one before the expiration date.<br>
* Check if power is still available when you turn off any of vehicles devices.
[[Image:ATX700 TCT key.png|500px]]
* Ignition is connected to the ignition relay output. As alternative, any other relay, which has power output when ignition is on, may be chosen.
</li>
 
</ol>
'''CONNECTING GROUND WIRE'''
<ol start="5">
 
<li>Go to '''Settings''' -> '''Select firmware''', then select '''ATx700 with development firmware''' and press '''Apply''':[[Image:ATX700 select firmware.png|500px]]
* Ground wire must be connected to the vehicle frame or metal parts that are fixed to the frame.
</li>
* If the wire is fixed with the bolt, the loop must be connected to the end of the wire.
<li>In the Discovered devices list, select your device and press '''Configure'''.</li>
* For better contact scrub paint from the spot where loop is going to be connected.
<li>The Device status window opens. It contains device, GNSS, and Cellular information.[[Image:{{{model}}} device status.png|1000px]]<br>[[Image:FTX buttons.png|left|120px]]
 
Save to device – saves configuration to device.<br><br>
}}
Upload file – loads configuration from file.<br><br>
 
Save to file – saves configuration to file.<br><br>
=='''LED INDICATIONS'''==
Update – update device firmware.<br><br>
 
Reset configuration – sets device configuration to default.<br><br>
This section is an explanation of LED indications on {{{model|FTC881}}} device.
<br>
<br>
Most important configuration sections are [https://wiki.teltonika-gps.com/view/{{{model}}}_Mobile_network Mobile network] (Server, Mobile network settings) and [https://wiki.teltonika-gps.com/view/{{{model}}}_Tracking_settings Tracking settings] (data collection parameters). More details about {{{model}}} configuration using TCT can be found [https://wiki.teltonika-gps.com/view/{{{model}}}_Configuration here].
</li>
</ol>


{{#switch: {{{model|FTC881}}}
<!-- FTx305 with TCT User key requirement
 
| FTC305
| FTC881
| FTM305 =
| FTC921
<ol>
| FTC961
<li>Download the TCT (compressed archive).</li>
| FTC305
<li>Extract the archive and launch the executable. The TCT will be installed.</li>
| FTM305 =
<li>Launch the TCT.</li>
'''NAVIGATION LED INDICATIONS'''
<li>Go to '''Settings''' -> '''User keys''', copy the <u>'''full key text from "BEGIN TCT KEY" to "END TCT KEY"'''</u> and paste in '''Add new key''' field, then press '''Add key''':<br>
<pre style="margin-left: 0px;">
BEGIN TCT KEY
  description: FTx305 with develop version firmware
  type:        ExpFWKey
  key:        7394b05f-f32a-4648-bd03-d61e7dfd0175
  expires:    2025-12-31
  signature:   v1|U2GAiWlZfOQkMN0pBeXDFhKZb6XES5ZvtCzcsfm9kyBkbPBaiwOl53v5uDRiefxqgIR6rJ4pAP2yg0bCZ77pO47iV8manPG/rMt5bKBJOgil8psW+Z58gwgZfZkU7q30EZy7prvAidsup92dnQ16tRefu+8EsUXS2rS0Uz8g0vVcJOPIwzWWRyVNCgW7zBXDl+bsZLXR2XHMhe0ftLy6MQoq6b3wlLMQuXCtd8/D5wnR/q5zPl9jVKJ3YUszRSxHLYlIht5vtb1uE0973WRdjvHlSqrKhjrEPrAgLueOWrDlMhYWWQVaMkWX41/Xd+r8M1oIhZlrBjONPWBWc2brAw==
END TCT KEY
</pre>
'''Note:''' This TCT key will expire on '''2025-12-31'''. Please contact us via HelpDesk to receive a new one before the expiration date.<br>
<br>[[Image:FTX305 TCT key.png|1000px]]
</li>
</ol>
<ol start="5">
<li>Go to '''Settings''' -> '''Select firmware''', then select '''FTx305 with develop version firmware''' and press '''Apply''':[[Image:FTX305 select firmware.png|1000px]]
</li>
<li>In the Discovered devices list, select your device and press '''Configure'''.</li>
<li>The Device status window opens. It contains device, GNSS, and Cellular information.[[Image:FTX device status.png|1000px]]<br>[[Image:FTX buttons.png|left|120px]]
Save to device – saves configuration to device.<br><br>
Upload file – loads configuration from file.<br><br>
Save to file – saves configuration to file.<br><br>
Update – update device firmware.<br><br>
Reset configuration – sets device configuration to default.<br><br>
<br>
Most important configuration sections are [https://wiki.teltonika-gps.com/view/{{{model}}}_Mobile_network Mobile network] (Server, Mobile network settings) and [https://wiki.teltonika-gps.com/view/{{{model}}}_Tracking_settings Tracking settings] (data collection parameters). More details about {{{model}}} configuration using TCT can be found [https://wiki.teltonika-gps.com/view/{{{model}}}_Configuration here].
</li>
</ol>
-->


<table class="nd-othertables_2" style="width:60%;">
|FTC880
<tr>
|FTM880 =  
        <th rowspan="1" style="width:50%; vertical-align: middle; text-align: center;">Behaviour</th>
# Download the TCT (compressed archive).
        <th rowspan="1" style="width:50%; vertical-align: middle; text-align: center;">Meaning</th>
# Extract the archive and launch the executable. The TCT will be installed.
    </tr>
# Launch the TCT.
<tr>
# In the Discovered devices list, select your device and press '''Configure'''.
        <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Permanently switched on</th>
# The Device status window opens. It contains device, GNSS and Cellular information.[[Image:{{{model}}} device status.png]]<br>[[Image:FTX buttons.png|left|120px]]
        <td style="vertical-align: middle; text-align: left; ">GNSS signal is not received</td>
Save to device – saves configuration to device.<br><br>
    </tr>
Upload file – loads configuration from file.<br><br>
<tr>
Save to file – saves configuration to file.<br><br>
        <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Blinking every second</th>
Update – update device firmware.<br><br>
        <td style="vertical-align: middle; text-align: left;">Normal mode, GNSS is working</td>
Reset configuration – sets device configuration to default.<br><br>
    </tr>
<tr>
        <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Off</th>
        <td style="vertical-align: middle; text-align: left;">GNSS is turned off because:<br/>Device is not working<br/>or<br/>Device is in sleep mode</td>
    </tr>
  <tr>
        <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Blinking fast
constantly</th>
        <td style="vertical-align: middle; text-align: left;">Device firmware is being flashed</td>
    </tr>
<tr>
</table>
<br>
<br>
'''STATUS LED INDICATIONS'''
Most important configuration sections are [https://wiki.teltonika-gps.com/view/{{{model}}}_Mobile_network Mobile network] (Server, Mobile network settings) and [https://wiki.teltonika-gps.com/view/{{{model}}}_Tracking_settings Tracking settings] (data collection parameters). More details about {{{model}}} configuration using TCT can be found [https://wiki.teltonika-gps.com/view/{{{model}}}_Configuration here].


<table class="nd-othertables_2" style="width:60%;">
| FTM887 =  
<tr>
# Download the TCT (compressed archive).
        <th rowspan="1" style="width:50%; vertical-align: middle; text-align: center;">Behaviour</th>
# Extract the archive and launch the executable. The TCT will be installed.
        <th rowspan="1" style="width:50%; vertical-align: middle; text-align: center;">Meaning</th>
# Launch the TCT.
    </tr>
# In the Discovered devices list, select your device and press '''Configure'''.
<tr>
# The Device status window opens. It contains device, GNSS and Cellular information.[[Image:{{{model}}} device status.png]]<br>[[Image:FTX buttons.png|left|120px]]
        <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Blinking every second</th>
Save to device – saves configuration to device.<br><br>
        <td style="vertical-align: middle; text-align: left;">Normal mode</td>
Upload file – loads configuration from file.<br><br>
    </tr>
Save to file – saves configuration to file.<br><br>
  <tr>
Update – update device firmware.<br><br>
        <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Blinking every two seconds</th>
Reset configuration – sets device configuration to default.<br><br>
        <td style="vertical-align: middle; text-align: left;">Sleep mode</td>
<br>
    </tr>
Most important configuration sections are [https://wiki.teltonika-gps.com/view/{{{model}}}_Mobile_network Mobile network] (Server, Mobile network settings) and [https://wiki.teltonika-gps.com/view/{{{model}}}_Tracking_settings Tracking settings] (data collection parameters). More details about {{{model}}} configuration using TCT can be found [https://wiki.teltonika-gps.com/view/{{{model}}}_Configuration here].
<tr>
        <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Blinking fast for a
short time</th>
        <td style="vertical-align: middle; text-align: left;">Modem activity</td>
    </tr>
<tr>
        <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Off</th>
        <td style="vertical-align: middle; text-align: left;">Device is not working<br/>or<br/>Device is in boot mode</td>
    </tr>
</table>


}}
| FTC887 =
 
# Download the TCT (compressed archive).
{{#switch: {{{model|FTC305}}}
# Extract the archive and launch the executable. The TCT will be installed.
| FTC305 =
# Launch the TCT.
=='''BASIC CHARACTERISTICS'''==
# In the Discovered devices list, select your device and press '''Configure'''.
# The Device status window opens. It contains device, GNSS and Cellular information.[[Image:{{{model}}} device status.png]]<br>[[Image:FTX buttons.png|left|120px]]
Save to device – saves configuration to device.<br><br>
Upload file – loads configuration from file.<br><br>
Save to file – saves configuration to file.<br><br>
Update – update device firmware.<br><br>
Reset configuration – sets device configuration to default.<br><br>
<br>
Most important configuration sections are [https://wiki.teltonika-gps.com/view/{{{model}}}_Mobile_network Mobile network] (Server, Mobile network settings) and [https://wiki.teltonika-gps.com/view/{{{model}}}_Tracking_settings Tracking settings] (data collection parameters). More details about {{{model}}} configuration using TCT can be found [https://wiki.teltonika-gps.com/view/{{{model}}}_Configuration here].
}}
 
=='''QUICK SMS CONFIGURATION'''==
The default configuration ensures best track quality and optimal data usage.<br>
 
Quickly set up your device by sending this SMS command to it: <br>
 
[[Image:FTX quick sms configuration.png|left|800px]]
<div style="clear:left;"></div>


<table class="nd-othertables_2" style="width:90%;">
=='''DEFAULT CONFIGURATION SETTINGS'''==
<tr>
{{#switch: {{{model}}}
        <th rowspan="1" style="width:30%; vertical-align: middle; text-align: left;">Module</th>
| #default =
        <th rowspan="1" style="width:60%; vertical-align: middle; text-align: left;"></th>
[[Image:FTX default configuration settings.png|left|800px]]
    </tr>
<div style="clear:left;"></div>
<tr>
 
        <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Name</th>
After successful SMS configuration, {{{model}}} device will synchronize time and update records to configured server. Time
        <td style="vertical-align: middle; text-align: left; ">'''FTC305-QJAB0:''' Quectel EG915U-EU, internal antennas, casing version <br> '''FTC305-QKAB0:''' Quectel EG915U-LA, internal antennas, casing version <br> '''FTC305-QJXB0:''' Quectel EG915U-EU, external antennas, external battery, no casing version <br> '''FTC305-QKXB0:''' Quectel EG915U-LA, external antennas, external battery, no casing version</td>
intervals and default I/O elements can be changed by using [https://wiki.teltonika-gps.com/view/{{{model}}}_Configuration TCT] or [https://wiki.teltonika-gps.com/view/{{{model}}}_Parameter_list Parameter list].
    </tr>
 
  <tr>
| ATM704
        <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Technology</th>
| ATC704
        <td style="vertical-align: middle; text-align: left; ">LTE CAT 1/GSM/GPRS/GNSS</td>
| ATM700
    </tr>
| ATC700 =
    <tr>
=== RECORDS SENDING TO SERVER ===
        <th rowspan="1" style="width:15%; vertical-align: middle; text-align: left;">GNSS</th>
A record with location will be transmitted to the server every 15 minutes, regardless of the product's movement status.
        <th rowspan="1" style="width:35%; vertical-align: middle; text-align: left;"></th>
 
    </tr>
=== SLEEP MODE ===
    <tr>
The device is configured with Power Off Sleep mode enabled by default to ensure maximum operating time.The device will not send any records until the server parameters (Domain, and port) are configured. During this time, all records are stored in the device’s internal memory. Once configured, the stored data is automatically transmitted to the specified server.
        <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">GNSS</th>
 
        <td style="vertical-align: middle; text-align: left; ">GPS, GLONASS, GALILEO, BEIDOU</td>
Time intervals and default I/O elements can be changed by using [https://wiki.teltonika-gps.com/view/{{{model}}}_Configuration TCT], [https://wiki.teltonika-gps.com/view/{{{model}}}_Parameter_list Parameter list] or FOTA Web.
    </tr>
}}
    <tr>
=='''MOUNTING RECOMMENDATIONS'''==
        <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Receiver</th>
 
        <td style="vertical-align: middle; text-align: left; ">L1: 75 channel</td>
{{#switch: {{{model}}}
    </tr>
| FTC887
    <tr>
| FTM887
        <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Tracking sensitivity</th>
| FTC881 =
        <td style="vertical-align: middle; text-align: left; ">-165 dBm</td>
'''DEVICE FASTENING'''
    </tr>
 
    <tr>
* Locate the battery in your vehicle. If present remove the battery cover to access the battery.
        <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Position Accuracy</th>
*  There is a double sided tape on the back of the device, use it to attach the device on the battery, so that the GNSS antenna and LEDs indicators are facing up.
        <td style="vertical-align: middle; text-align: left; ">< 1.8 m CEP</td>
 
    </tr>
'''CONNECTING POWER SOURCE'''
    <tr>
 
        <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Velocity Accuracy</th>
*  Device power wire is designed to be directly connected to the positive terminal fastener of the vehicle battery.
        <td style="vertical-align: middle; text-align: left; ">< 0.1 m/s (within +/- 15% error)</td>
 
    </tr>
'''CONNECTING GROUND WIRE'''
    <tr>
 
        <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Hot start</th>
* Device ground wire is designed to be directly connected to the negative terminal fastener of the vehicle battery.
        <td style="vertical-align: middle; text-align: left; ">< 1 s</td>
 
    </tr>
| FTC920
    <tr>
| FTC921
        <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Warm start</th>
| FTC924
        <td style="vertical-align: middle; text-align: left; ">< 25 s</td>
| FTC927
    </tr>
| FTC965
        <th rowspan="1" style="width:15%; vertical-align: middle; text-align: left;">Cellular</th>
| FTC961 =
        <th rowspan="1" style="width:35%; vertical-align: middle; text-align: left;"></th>
'''CONNECTING WIRES'''
    <tr>
 
        <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">2G bands</th>
* Wires should be fastened to stable wires or other non-moving parts. Any heat emitting and/or moving objects should be kept away from the wires.
        <td style="vertical-align: middle; text-align: left; ">GSM: B2/B3/B5/B8</td>
* There should be no exposed wires. If factory isolation was removed while connecting wires, the isolation material should be applied.
    </tr>
* If the wires are placed in the exterior or in places where they can be damaged or exposed to heat, humidity, dirt, etc., additional isolation should be applied and the wires should not be loose.<br />
    <tr>
* Wires cannot be connected to the board computers or control units.
        <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">4G bands</th>
 
        <td style="vertical-align: middle; text-align: left; ">'''FTC305-QJAB0:''' <br> LTE FDD (EG915U-EU): <br> B1/B3/B5/B7/B8/B20/B28 <br> '''FTC305-QJXB0:''' <br> LTE FDD (EG915U-EU): <br> B1/B3/B5/B7/B8/B20/B28 <br> '''FTC305-QKAB0:''' <br> LTE FDD (EG915U-LA): <br> B2/B3/B4/B5/B7/B8/B28/B66 <br> '''FTC305-QKXB0:''' <br> LTE FDD (EG915U-LA): <br> B2/B3/B4/B5/B7/B8/B28/B66</td>
'''CONNECTING POWER SOURCE'''
    </tr>
 
    <tr>
* Be sure that after the car computer goes to sleep mode, power might be still available on the power wires. Depending on car, this may happen in 5 to 30 minutes period.
        <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Data transfer</th>
* When module is connected, measure voltage again to make sure it did not decrease.
        <td style="vertical-align: middle; text-align: left; ">LTE FDD (CAT 1): Max. 10 Mbps (DL) / Max. 5 Mbps (UL) <br> GSM (GPRS): Max. 85.6 Kbps (DL) / Max. 85.6 Kbps (UL)</td>
* It is recommended to connect to the main power cable in the fuse box.
    </tr>
* 3 A, 125 V external fuse shall be used.
    <tr>
 
        <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Transmit power</th>
'''CONNECTING GROUND WIRE'''
        <td style="vertical-align: middle; text-align: left; ">Class 5 for GSM850/900: 30±5dBM <br> Class 3 for GSM1800/1900:29±5dBM <br> Class 3 for LTE-FDD: 26±5dBM</td>
 
    </tr>
* Ground wire is connected to the vehicle frame or metal parts that are fixed to the frame.
    <tr>
* If the wire is fixed with the bolt, the loop must be connected to the end of the wire.
        <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Data support</th>
* For better contact scrub paint from the spot where loop is going to be connected.
        <td style="vertical-align: middle; text-align: left; ">SMS (TEXT, PDU), Network protocols (TCP, UDP)</td>
 
    </tr>
| FTC305
<tr>
| FTM305 =
        <th rowspan="1" style="width:15%; vertical-align: middle; text-align: left;">Power</th>
'''CONNECTING WIRES'''
        <th rowspan="1" style="width:35%; vertical-align: middle; text-align: left;"></th>
 
    </tr>
* Wires should be fastened to the other wires or nonmoving parts. Do not place the wires near moving or heat-emitting objects.
    <tr>
* All electrical connections must be properly isolated. No bare wires should be visible. Re-apply isolation to wires if you removed factory isolation during installation.
        <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Input voltage range</th>
* If the wires are placed in the exterior or in places where they can be damaged or exposed to heat, humidity, dirt, etc., additional isolation should be applied.
        <td style="vertical-align: middle; text-align: left; ">10 - 97 V DC</td>
 
    </tr>
'''CONNECTING POWER SOURCE'''
    <tr>
* Ensure that after the vehicle computer falls asleep, power is still available on chosen wire. Depending on vehicle, this may happen in 5 to 30 minutes period.
        <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Back-up battery</th>
* When module is connected, measure voltage again to make sure it did not decrease.
        <td style="vertical-align: middle; text-align: left; ">'''Casing version:''' 380 mAh Li-ion battery 3.7V (1.41 Wh) <br> '''No casing version:''' 1200 mAh Li-ion battery 3.7 V (4.44 Wh) (External)</td>
* It is recommended to connect main power cable to the main battery of the vehicle.
    </tr>
 
    <tr>
'''CONNECTING IGNITION WIRE'''
        <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Internal fuse</th>
 
        <td style="vertical-align: middle; text-align: left; ">3A</td>
* Make sure that you have selected the correct wire for ignition signal - the electrical signal from the wire should be present after starting the engine.
    </tr>
* Check if this is not an ACC wire (when key is in the first position, most of the vehicle electronics are ON).
    <tr>
* Check if power is still available when you turn off any of vehicles devices.
        <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Power Consumption</th>
* Ignition is connected to the ignition relay output. As alternative, any other relay, which has power output when ignition is on, may be chosen.
        <td style="vertical-align: middle; text-align: left; ">At 12V < 40 mA (Nominal with no load) <br> At 12V < 0.25 A Max (with full Load/Peak)</td>
 
    </tr>
'''CONNECTING GROUND WIRE'''
<tr>
 
        <th rowspan="1" style="width:15%; vertical-align: middle; text-align: left;">Bluetooth® Technology</th>
* Ground wire must be connected to the vehicle frame or metal parts that are fixed to the frame.
        <th rowspan="1" style="width:35%; vertical-align: middle; text-align: left;"></th>
* If the wire is fixed with the bolt, the loop must be connected to the end of the wire.
    </tr>
* For better contact scrub paint from the spot where loop is going to be connected.
    <tr>
 
        <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Specification</th>
| FTC880
        <td style="vertical-align: middle; text-align: left; ">5.3 + LE</td>
| FTM880 =
    </tr>
'''CONNECTING WIRES'''
  <tr>
 
         <th rowspan="1" style="width:15%; vertical-align: middle; text-align: left;">Interface</th>
* Wires should be fastened to the other wires or nonmoving parts. Do not place the wires near moving or heat-emitting objects.
         <th rowspan="1" style="width:35%; vertical-align: middle; text-align: left;"></th>
* All electrical connections must be properly isolated. No bare wires should be visible. Re-apply isolation to wires if you removed factory isolation during installation.
    </tr>
* If the wires are placed in the exterior or in places where they can be damaged or exposed to heat, humidity, dirt, etc., additional isolation should be applied.
    <tr>
 
        <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Digital Inputs</th>
'''CONNECTING POWER SOURCE'''
        <td style="vertical-align: middle; text-align: left; ">1</td>
* Ensure that after the vehicle computer falls asleep, power is still available on chosen wire. Depending on vehicle, this may happen in 5 to 30 minutes period.
* When module is connected, measure voltage again to make sure it did not decrease.
* It is recommended to connect main power cable to the main battery of the vehicle.
 
'''CONNECTING GROUND WIRE'''
 
* Ground wire must be connected to the vehicle frame or metal parts that are fixed to the frame.
* If the wire is fixed with the bolt, the loop must be connected to the end of the wire.
* For better contact scrub paint from the spot where loop is going to be connected.
 
| FTM134
| FTC134 =  
'''CONNECTING WIRES'''
 
* Wires should be fastened to stable wires or other non-moving parts. Any heat emitting and/or moving objects should be kept away from the wires.
* There should be no exposed wires. If factory isolation was removed while connecting wires, the isolation material should be applied.
* If the wires are placed in the exterior or in places where they can be damaged or exposed to heat, humidity, dirt, etc., additional isolation should be applied and the wires should not be loose.
* Wires cannot be connected to the board computers or control units.
 
'''CONNECTING POWER SOURCE'''
* Be sure that after the car computer goes to sleep mode, power might be still available on the power wires. Depending on car, this may happen in 5 to 30 minutes period.
* When module is connected, measure voltage again to make sure it did not decrease.
* It is recommended to connect to the main power cable in the fuse box.
* 3 A, 125 V external fuse shall be used.
 
'''CONNECTING GROUND WIRE'''
* Ground wire is connected to the vehicle frame or metal parts that are fixed to the frame.
* If the wire is fixed with the bolt, the loop must be connected to the end of the wire.
* For better contact scrub paint from the spot where loop is going to be connected.
 
| ATM700
| ATC700 =  
[[File:{{{model}}} Mounting recommendations.png]]
}}
 
=='''LED INDICATIONS'''==
 
This section is an explanation of LED indications on {{{model}}} device.
<br>
 
{{#switch: {{{model}}}
| FTC164
| FTC887
| FTM887
| FTM134
| FTC134
| FTC880
| FTM880
| FTC881
| FTC921
| FTC961
| FTC305
| FTM305 =
'''NAVIGATION LED INDICATIONS'''
 
<table class="nd-othertables_2" style="width:60%;">
  <tr>
         <th rowspan="1" style="width:50%; vertical-align: middle; text-align: center;">Behaviour</th>
         <th rowspan="1" style="width:50%; vertical-align: middle; text-align: center;">Meaning</th>
     </tr>
     </tr>
    <tr>
<tr>
         <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Digital Outputs</th>
         <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Blinking every second</th>
         <td style="vertical-align: middle; text-align: left; ">2</td>
         <td style="vertical-align: middle; text-align: left;">GNSS module is working, GNSS fix is acquired (normal operation)</td>
     </tr>
     </tr>
    <tr>
<tr>
         <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Analog Inputs</th>
         <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Permanently switched on</th>
         <td style="vertical-align: middle; text-align: left; ">1</td>
         <td style="vertical-align: middle; text-align: left; ">GNSS module is working, but fix is not acquired (no position)</td>
     </tr>
     </tr>
    <tr>
<tr>
         <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">1-Wire</th>
         <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Off</th>
         <td style="vertical-align: middle; text-align: left; ">1</td>
         <td style="vertical-align: middle; text-align: left;">GNSS module is off because: (a) the device is not working or (b) the device is in sleep mode</td>
     </tr>
     </tr>
    <tr>
</table>
         <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">CAN</th>
<br>
         <td style="vertical-align: middle; text-align: left; ">1</td>
'''STATUS LED INDICATIONS'''
 
<table class="nd-othertables_2" style="width:60%;">
<tr>
         <th rowspan="1" style="width:50%; vertical-align: middle; text-align: center;">Behaviour</th>
         <th rowspan="1" style="width:50%; vertical-align: middle; text-align: center;">Meaning</th>
     </tr>
     </tr>
    <tr>
<tr>
         <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">GNSS antenna</th>
         <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Blinking every second</th>
         <td style="vertical-align: middle; text-align: left; ">'''Casing version:''' Internal High Gain <br> '''No casing version:''' External (SMA female connector)</td>
         <td style="vertical-align: middle; text-align: left;">Device is working, GPRS session is active (normal operation)</td>
     </tr>
     </tr>
    <tr>
  <tr>
         <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">GSM antenna</th>
         <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">On</th>
         <td style="vertical-align: middle; text-align: left; ">'''Casing version:''' Internal High Gain <br> '''No casing version:''' External (RP SMA female connector)</td>
         <td style="vertical-align: middle; text-align: left;">Device is working, no active GPRS sessions</td>
     </tr>
     </tr>
    <tr>
<tr>
         <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">USB</th>
         <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Off</th>
         <td style="vertical-align: middle; text-align: left; ">2.0 USB Type-C</td>
         <td style="vertical-align: middle; text-align: left;">Device is not working</td>
     </tr>
     </tr>
     <tr>
</table>
        <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">LED indication</th>
 
        <td style="vertical-align: middle; text-align: left; ">2 status LED lights</td>
| ATM704
| ATC704
| ATM700
| ATC700 =
 
<table class="nd-othertables_2" style="width:80%;">
 <tr>
        <th rowspan="1" style="width:30%; vertical-align: middle; text-align: center;">Meaning</th>
        <th rowspan="1" style="width:10%; vertical-align: middle; text-align: center;">Colour</th>
        <th rowspan="1" style="width:30%; vertical-align: middle; text-align: center;">Behaviour</th>
        <th rowspan="1" style="width:30%; vertical-align: middle; text-align: center;">Duration</th>
    </tr>
 <tr>
    <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: center; color:black">Power On</th>
    <td style="vertical-align: middle; text-align: center;">Green</td>
    <td style="vertical-align: middle; text-align: center;">Steady</td>
    <td style="vertical-align: middle; text-align: center;">3 s</td>
  </tr>
 <tr>
    <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: center; color:black">Low Battery</th>
    <td style="vertical-align: middle; text-align: center;">Red</td>
    <td style="vertical-align: middle; text-align: center;">Blinking - 1 s ON / 1 s OFF</td>
     <td style="vertical-align: middle; text-align: center;">Until power off</td>
  </tr>
 <tr>
    <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: center; color:black">Charging</th>
    <td style="vertical-align: middle; text-align: center;">Yellow</td>
    <td style="vertical-align: middle; text-align: center;">Pulsing - fade in 2 s / fade out 2 s</td>
    <td style="vertical-align: middle; text-align: center;">Until charged or USB disconnected</td>
  </tr>
 <tr>
    <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: center; color:black">100% charged</th>
    <td style="vertical-align: middle; text-align: center;">Green</td>
    <td style="vertical-align: middle; text-align: center;">Steady</td>
    <td style="vertical-align: middle; text-align: center;">Until USB disconnected</td>
  </tr>
 <tr>
    <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: center; color:black">FW update</th>
    <td style="vertical-align: middle; text-align: center;">Blue</td>
    <td style="vertical-align: middle; text-align: center;">Blinking - 0.1 s ON / 0.1 s OFF </td>
    <td style="vertical-align: middle; text-align: center;">Until update finished</td>
  </tr>
 <tr>
    <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: center; color:black">CFG uploading</th>
    <td style="vertical-align: middle; text-align: center;">Blue</td>
    <td style="vertical-align: middle; text-align: center;">Steady</td>
    <td style="vertical-align: middle; text-align: center;">3 s</td>
  </tr>
 <tr>
    <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: center; color:black">Periodic record sending</th>
    <td style="vertical-align: middle; text-align: center;">Yellow</td>
    <td style="vertical-align: middle; text-align: center;">Blinking - 0.2 s ON / 2 s OFF</td>
    <td style="vertical-align: middle; text-align: center;">Until record is sent or failed</td>
  </tr>
 <tr>
    <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: center; color:black">Record sent with GNSS fix</th>
    <td style="vertical-align: middle; text-align: center;">Blue</td>
    <td style="vertical-align: middle; text-align: center;">Steady</td>
    <td style="vertical-align: middle; text-align: center;">3 s</td>
  </tr>
 <tr>
    <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: center; color:black">Record sent no GNSS fix</th>
    <td style="vertical-align: middle; text-align: center;">Yellow</td>
    <td style="vertical-align: middle; text-align: center;">Steady</td>
    <td style="vertical-align: middle; text-align: center;">3 s</td>
  </tr>
 <tr>
    <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: center; color:black">Record sending failed and GNSS failed</th>
    <td style="vertical-align: middle; text-align: center;">Red</td>
    <td style="vertical-align: middle; text-align: center;">Steady</td>
    <td style="vertical-align: middle; text-align: center;">3 s</td>
  </tr>
 <tr>
    <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: center; color:black">GNSS OK, but record sending failed</th>
    <td style="vertical-align: middle; text-align: center;">Red</td>
    <td style="vertical-align: middle; text-align: center;">Blinking - 0.5 s ON / 0.5 s OFF</td>
    <td style="vertical-align: middle; text-align: center;">3 s</td>
  </tr>
<tr>
    <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: center; color:black">Alarm</th>
    <td style="vertical-align: middle; text-align: center;">Red</td>
    <td style="vertical-align: middle; text-align: center;">Pulsing - 0.5 s fade in / 0.5 s fade out</td>
    <td style="vertical-align: middle; text-align: center;">6 s</td>
  </tr>
<tr>
    <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: center; color:black">Normal operation </th>
    <td style="vertical-align: middle; text-align: center;">Blue</td>
    <td style="vertical-align: middle; text-align: center;">Blinking - 0.5 s ON / 1 min OFF</td>
    <td style="vertical-align: middle; text-align: center;">In Idle</td>
  </tr>
<tr>
    <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: center; color:black">Power OFF</th>
    <td style="vertical-align: middle; text-align: center;">Red</td>
    <td style="vertical-align: middle; text-align: center;">Steady</td>
    <td style="vertical-align: middle; text-align: center;">2 s</td>
  </tr>
</table>
 
 
}}
 
=='''BASIC CHARACTERISTICS'''==
{{#switch: {{{model}}}
| FTM800 =
<table class="nd-othertables_2" style="width:90%;">
<tr>
        <th rowspan="1" style="width:30%; vertical-align: middle; text-align: left;">Product</th>
        <th rowspan="1" style="width:60%; vertical-align: middle; text-align: left;"></th>
     </tr>
     </tr>
    <tr>
<tr>
         <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">SIM</th>
         <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Name</th>
         <td style="vertical-align: middle; text-align: left; ">Nano-SIM</td>
         <td style="vertical-align: middle; text-align: left; ">'''FTM800-Q3AB0'''</td>  
     </tr>
     </tr>
    <tr>
<tr>
         <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Memory</th>
<tr>
         <td style="vertical-align: middle; text-align: left; ">128MB internal flash memory</td>
         <th rowspan="1" style="width:30%; vertical-align: middle; text-align: left;">Module</th>
         <th rowspan="1" style="width:60%; vertical-align: middle; text-align: left;"></th>
     </tr>
     </tr>
  <tr>
<tr>
         <th rowspan="1" style="width:15%; vertical-align: middle; text-align: left;">Physical Specification</th>
         <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Name</th>
         <th rowspan="1" style="width:35%; vertical-align: middle; text-align: left;"></th>
         <td style="vertical-align: middle; text-align: left; ">'''FTM800-Q3AB0:''' Quectel BG95-M3 with AG3335 </td>
     </tr>
     </tr>
    <tr>
<tr>
         <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Dimensions</th>
         <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Technology</th>
         <td style="vertical-align: middle; text-align: left; ">'''Casing version:''' 69 x 41 x 20.9 mm (L x W x H) <br> '''No casing version:''' 62 x 39.6 x 11.5 mm (L x W x H) <br>
         <td style="vertical-align: middle; text-align: left; ">LTE CAT M1/NB-IoT/GSM/GPRS/GNSS</td>
* '''External GNSS antenna:''' 46 x 44 x 13 mm (L x W x H) <br>
* '''External Cellular antenna:''' 115 x 22 x 6 mm (L x W x H)</td>
     </tr>
     </tr>
     <tr>
     <tr>
        <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Weight</th>
         <th rowspan="1" style="width:15%; vertical-align: middle; text-align: left;">GNSS</th>
        <td style="vertical-align: middle; text-align: left; ">'''Casing version:''' 76.8 g <br> '''No casing version (with accessories):''' 126.1 g</td>
    </tr>
<tr>
         <th rowspan="1" style="width:15%; vertical-align: middle; text-align: left;">Operating Environment</th>
         <th rowspan="1" style="width:35%; vertical-align: middle; text-align: left;"></th>
         <th rowspan="1" style="width:35%; vertical-align: middle; text-align: left;"></th>
     </tr>
     </tr>
     <tr>
     <tr>
         <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Operating temperature</th>
         <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">GNSS</th>
         <td style="vertical-align: middle; text-align: left; ">-30 °C to +85 °C</td>
         <td style="vertical-align: middle; text-align: left; ">GPS, GLONASS, GALILEO, BEIDOU</td>
     </tr>
     </tr>
     <tr>
     <tr>
         <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Storage temperature</th>
         <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Receiver</th>
         <td style="vertical-align: middle; text-align: left; ">-30 °C to +85 °C</td>
         <td style="vertical-align: middle; text-align: left; ">L1: 75 channel</td>
     </tr>
     </tr>
     <tr>
     <tr>
         <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Operating humidity</th>
         <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Tracking sensitivity</th>
         <td style="vertical-align: middle; text-align: left; ">65 ± 20% non-condensing</td>
         <td style="vertical-align: middle; text-align: left; ">-165 dBm</td>
     </tr>
     </tr>
     <tr>
     <tr>
         <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Ingress protection rating</th>
         <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Position Accuracy</th>
         <td style="vertical-align: middle; text-align: left; ">'''Casing version:''' IP67 <br> '''No casing version:''' N/A</td>
         <td style="vertical-align: middle; text-align: left; ">< 1.8 m CEP</td>
     </tr>
     </tr>
     <tr>
     <tr>
         <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Battery charge
         <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Velocity Accuracy</th>
temperature</th>
         <td style="vertical-align: middle; text-align: left; ">< 0.1 m/s (within +/- 15% error)</td>
         <td style="vertical-align: middle; text-align: left; ">0 °C to +45 °C</td>
     </tr>
     </tr>
     <tr>
     <tr>
         <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Battery discharge temperature</th>
         <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Hot start</th>
         <td style="vertical-align: middle; text-align: left; ">-20 °C to +60 °C</td>
        <td style="vertical-align: middle; text-align: left; ">-</td>
    </tr>
    <tr>
        <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Warm start</th>
         <td style="vertical-align: middle; text-align: left; ">-</td>
     </tr>
     </tr>
     <tr>
     <tr>
         <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Battery storage
         <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Hot start</th>
conditions</th>
         <td style="vertical-align: middle; text-align: left; ">-</td>
         <td style="vertical-align: middle; text-align: left; ">'''Casing version:''' -10 °C to +25 °C for 3 or more months <br> '''No casing version:''' -20 °C to +45 °C for 3 or more months</td>
     </tr>
     </tr>
<tr>
         <th rowspan="1" style="width:15%; vertical-align: middle; text-align: left;">Cellular</th>
         <th rowspan="1" style="width:15%; vertical-align: middle; text-align: left;">Data Codec</th>
         <th rowspan="1" style="width:35%; vertical-align: middle; text-align: left;"></th>
         <th rowspan="1" style="width:35%; vertical-align: middle; text-align: left;"></th>
        <tr>
        <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Technology</th>
        <td style="vertical-align: middle; text-align: left; ">LTE CAT M1/NB-IoT/GSM</td>
     </tr>
     </tr>
     <tr>
     <tr>
         <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Codec support</th>
         <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">2G bands</th>
         <td style="vertical-align: middle; text-align: left; ">[https://wiki.teltonika-gps.com/view/Codec#Codec_8_Extended Codec 8 Extended]</td>
         <td style="vertical-align: middle; text-align: left; ">'''FTC800-QJAB0:''' GSM: B2/B3/B5/B8 </td>
    </tr>
<tr>
        <th rowspan="1" style="width:15%; vertical-align: middle; text-align: left;">Features</th>
        <th rowspan="1" style="width:35%; vertical-align: middle; text-align: left;"></th>
     </tr>
     </tr>
     <tr>
     <tr>
         <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Sensors</th>
         <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">4G bands</th>
         <td style="vertical-align: middle; text-align: left; ">Accelerometer</td>
         <td style="vertical-align: middle; text-align: left; "> '''FTM800-Q3AB0:'''<br>LTE FDD (CAT M1): B1/B2/B3/B4/B5/B8/B12/B13/B18/B19/B20/B25/B26/B27/B28/B66/B85
            <br> LTE-TDD (CAT NB2): B1/B2/B3/B4/B5/B8/B12/B13/B18/B19/B20/B25/B28/B66/B71/B85 </td>
    </tr>
    <tr>
        <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Data transfer</th>
        <td style="vertical-align: middle; text-align: left; ">LTE FDD (CAT 1): Max. 10 Kbps (DL) / Max. 5 Kbps (UL) <br>GSM (GPRS): Max. 85.6 Kbps (DL) / Max. 85.6 Kbps (UL)</td>
     </tr>
     </tr>
     <tr>
     <tr>
         <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Scenarios</th>
         <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Transmit power</th>
         <td style="vertical-align: middle; text-align: left; ">[https://wiki.teltonika-gps.com/view/FTC305_Features Green Driving, Over Speeding detection, Jamming detection, Unplug detection, Crash detection, Manual CAN data reading, Manual CAN commands]</td>
         <td style="vertical-align: middle; text-align: left; ">Class 5 for GSM850/900: 30±5dBm Class 3 for GSM1800/1900: 29±5dBm <br> Class 3 for LTE-FDD: 26±5dBm</td>
     </tr>
     </tr>
     <tr>
     <tr>
         <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Sleep modes</th>
         <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Data support</th>
         <td style="vertical-align: middle; text-align: left; ">[https://wiki.teltonika-gps.com/view/FTC305_Sleep_modes Online sleep, Deep sleep, Power off sleep]</td>
         <td style="vertical-align: middle; text-align: left; ">SMS (TEXT, PDU), Network protocols (TCP, UDP)</td>
    </tr>
<tr>
        <th rowspan="1" style="width:15%; vertical-align: middle; text-align: left;">Power</th>
        <th rowspan="1" style="width:35%; vertical-align: middle; text-align: left;"></th>
     </tr>
     </tr>
     <tr>
     <tr>
         <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Configuration and firmware update</th>
         <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Input voltage range</th>
         <td style="vertical-align: middle; text-align: left; ">[https://wiki.teltonika-gps.com/view/FOTA_WEB FOTA WEB], [https://wiki.teltonika-gps.com/view/Telematics_Configuration_Tool_(TCT) Telematics Configuration Tool (TCT)]</td>
         <td style="vertical-align: middle; text-align: left; ">10 - 30 V DC</td>
     </tr>
     </tr>
     <tr>
     <tr>
         <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Time Synchronization</th>
         <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Back-up battery</th>
         <td style="vertical-align: middle; text-align: left; ">GNSS, NTP, NITZ</td>
         <td style="vertical-align: middle; text-align: left; ">100mAh Li-Ion battery 3.7V (0.37 Wh) </td>
     </tr>
     </tr>
     <tr>
     <tr>
         <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Ignition detection</th>
         <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Internal fuse</th>
         <td style="vertical-align: middle; text-align: left; ">Digital Input 1, Accelerometer, External Power Voltage</td>
         <td style="vertical-align: middle; text-align: left; ">3A</td>
     </tr>
     </tr>
</table>
    <tr>
 
         <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Power Consumption</th>
| FTM305 =
         <td style="vertical-align: middle; text-align: left; "> TBA </td>
=='''BASIC CHARACTERISTICS'''==
<table class="nd-othertables_2" style="width:90%;">
<tr>
         <th rowspan="1" style="width:30%; vertical-align: middle; text-align: left;">Module</th>
         <th rowspan="1" style="width:60%; vertical-align: middle; text-align: left;"></th>
     </tr>
     </tr>
  <tr>
  <tr>
         <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Name</th>
         <th rowspan="1" style="width:15%; vertical-align: middle; text-align: left;">Interface</th>
         <td style="vertical-align: middle; text-align: left; ">'''FTM305-Q2AB0:''' Quectel BG95-M1, internal antennas, casing version <br> '''FTM305-Q3AB0:''' Quectel BG95-M3, internal antennas, casing version <br> '''FTM305-Q5AB0:''' Quectel BG95-M6, internal antennas, casing version</td>
         <th rowspan="1" style="width:35%; vertical-align: middle; text-align: left;"></th>
    </tr>
<tr>
        <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Technology</th>
        <td style="vertical-align: middle; text-align: left; ">LTE CAT M1/GSM/GPRS/GNSS</td>
     </tr>
     </tr>
     <tr>
     <tr>
         <th rowspan="1" style="width:15%; vertical-align: middle; text-align: left;">GNSS</th>
         <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">GNSS antenna</th>
         <th rowspan="1" style="width:35%; vertical-align: middle; text-align: left;"></th>
         <td style="vertical-align: middle; text-align: left; ">Internal High Gain </td>
     </tr>
     </tr>
     <tr>
     <tr>
         <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">GNSS</th>
         <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">GSM antenna</th>
         <td style="vertical-align: middle; text-align: left; ">GPS, GLONASS, GALILEO, BEIDOU</td>
         <td style="vertical-align: middle; text-align: left; ">Internal High Gain </td>
     </tr>
     </tr>
     <tr>
     <tr>
         <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Receiver</th>
         <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">USB</th>
         <td style="vertical-align: middle; text-align: left; ">L1: 75 channel</td>
         <td style="vertical-align: middle; text-align: left; ">2.0 USB Type-C</td>
     </tr>
     </tr>
     <tr>
     <tr>
         <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Tracking sensitivity</th>
         <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">LED indication</th>
         <td style="vertical-align: middle; text-align: left; ">-165 dBm</td>
         <td style="vertical-align: middle; text-align: left; ">2 status LED lights</td>
     </tr>
     </tr>
     <tr>
     <tr>
         <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Position Accuracy</th>
         <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">SIM</th>
         <td style="vertical-align: middle; text-align: left; ">< 1.8 m CEP</td>
         <td style="vertical-align: middle; text-align: left; ">Nano-SIM</td>
     </tr>
     </tr>
     <tr>
     <tr>
         <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Velocity Accuracy</th>
         <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Memory</th>
         <td style="vertical-align: middle; text-align: left; ">< 0.1 m/s (within +/- 15% error)</td>
         <td style="vertical-align: middle; text-align: left; ">128MB internal flash memory</td>
    </tr>
  <tr>
        <th rowspan="1" style="width:15%; vertical-align: middle; text-align: left;">Physical Specification</th>
        <th rowspan="1" style="width:35%; vertical-align: middle; text-align: left;"></th>
     </tr>
     </tr>
     <tr>
     <tr>
         <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Hot start</th>
         <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Dimensions</th>
         <td style="vertical-align: middle; text-align: left; ">< 1 s</td>
         <td style="vertical-align: middle; text-align: left; ">TBA</td>
     </tr>
     </tr>
    <tr>
    <tr>
         <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Warm start</th>
         <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Weight</th>
         <td style="vertical-align: middle; text-align: left; ">< 25 s</td>
         <td style="vertical-align: middle; text-align: left; ">TBA</td>
     </tr>
     </tr>
         <th rowspan="1" style="width:15%; vertical-align: middle; text-align: left;">Cellular</th>
<tr>
         <th rowspan="1" style="width:15%; vertical-align: middle; text-align: left;">Operating Environment</th>
         <th rowspan="1" style="width:35%; vertical-align: middle; text-align: left;"></th>
         <th rowspan="1" style="width:35%; vertical-align: middle; text-align: left;"></th>
    </tr>
     <tr>
     <tr>
         <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">2G bands</th>
         <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Operating temperature (without battery)</th>
         <td style="vertical-align: middle; text-align: left; ">GSM: B2/B3/B5/B8</td>
         <td style="vertical-align: middle; text-align: left; ">-30 °C to +85 °C</td>
     </tr>
     </tr>
     <tr>
     <tr>
         <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">4G LTE Cat M1 bands</th>
         <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Storage temperature (without battery)</th>
         <td style="vertical-align: middle; text-align: left; ">'''BG95-M1:''' <br> LTE FDD (CAT M1 Only): <br> B1/B2/B3/B4/B5/B8/B12/B13/B18/B19/B20/B25/B26/B27/B28/B66/B85 <br> '''BG95-M3:''' <br> LTE FDD (CAT M1): <br> B1/B2/B3/B4/B5/B8/B12/B13/B18/B19/B20/B25/B26/B27/B28/B66/B85 <br> LTE FDD (CAT NB2): <br> B1/B2/B3/B4/B5/B8/B12/B13/B18/B19/B20/B25/B28/B66/B71/B85 <br> '''BG95-M6:''' LTE FDD (CAT M1): <br> B1/B2/B3/B4/B5/B8/B12/B13/B18/B19/B2/B25/B26/B27/B28/B66/B85 <br> LTE FDD (CAT NB2) <br> B1/B2/B3/B4/B5/B8/B12/B13/B18/B19/B20/B25/B28/B66/B71/B85</td>
         <td style="vertical-align: middle; text-align: left; ">-30 °C to +85 °C</td>
     </tr>
     </tr>
     <tr>
     <tr>
         <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Data transfer</th>
         <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Operating temperature (with battery)</th>
         <td style="vertical-align: middle; text-align: left; ">LTE FDD (CAT 1): Max. 10 Mbps (DL) / Max. 5 Mbps (UL) <br> GSM (GPRS): Max. 85.6 Kbps (DL) / Max. 85.6 Kbps (UL)</td>
         <td style="vertical-align: middle; text-align: left; ">0 °C to +45 °C</td>
     </tr>
     </tr>
     <tr>
     <tr>
         <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Transmit power</th>
         <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Storage temperature (with battery)</th>
         <td style="vertical-align: middle; text-align: left; ">Class 5 for GSM850/900: 30±5dBM <br> Class 3 for GSM1800/1900:29±5dBM <br> Class 3 for LTE-FDD: 26±5dBM</td>
         <td style="vertical-align: middle; text-align: left; ">-20 °C to +45 °C for 1 month <br> -20 °C to +35 °C for 6 months</td>
     </tr>
     </tr>
     <tr>
     <tr>
         <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Data support</th>
         <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Operating humidity</th>
         <td style="vertical-align: middle; text-align: left; ">SMS (TEXT, PDU), Network protocols (TCP, UDP)</td>
         <td style="vertical-align: middle; text-align: left; ">5% to 95% non-condensing</td>
    </tr>
<tr>
        <th rowspan="1" style="width:15%; vertical-align: middle; text-align: left;">Power</th>
        <th rowspan="1" style="width:35%; vertical-align: middle; text-align: left;"></th>
     </tr>
     </tr>
     <tr>
     <tr>
         <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Input voltage range</th>
         <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Ingress protection rating</th>
         <td style="vertical-align: middle; text-align: left; ">10 - 97 V DC</td>
         <td style="vertical-align: middle; text-align: left; ">IP41</td>
     </tr>
     </tr>
     <tr>
     <tr>
         <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Back-up battery</th>
         <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Battery charge
         <td style="vertical-align: middle; text-align: left; ">380 mAh Li-ion battery 3.7V (1.41 Wh)</td>
temperature</th>
         <td style="vertical-align: middle; text-align: left; ">0 °C to +45 °C</td>
     </tr>
     </tr>
     <tr>
     <tr>
         <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Internal fuse</th>
         <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Battery discharge temperature</th>
         <td style="vertical-align: middle; text-align: left; ">3A</td>
         <td style="vertical-align: middle; text-align: left; ">-20 °C to +60 °C</td>
     </tr>
     </tr>
     <tr>
     <tr>
         <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Power Consumption</th>
         <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Battery storage
         <td style="vertical-align: middle; text-align: left; ">At 12V < 40 mA (Nominal with no load) <br> At 12V < 0.25 A Max (with full Load/Peak)</td>
conditions</th>
         <td style="vertical-align: middle; text-align: left; ">-10 °C to +50 °C for 1 month<br> -10 °C to +35 °C for 3 months<br> 0 °C to +30 °C for 1 year </td>
     </tr>
     </tr>
<tr>
<tr>
         <th rowspan="1" style="width:15%; vertical-align: middle; text-align: left;">Bluetooth® Technology</th>
         <th rowspan="1" style="width:15%; vertical-align: middle; text-align: left;">Data Codec</th>
         <th rowspan="1" style="width:35%; vertical-align: middle; text-align: left;"></th>
         <th rowspan="1" style="width:35%; vertical-align: middle; text-align: left;"></th>
     </tr>
     </tr>
     <tr>
     <tr>
         <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Specification</th>
         <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Codec support</th>
         <td style="vertical-align: middle; text-align: left; ">5.3 + LE</td>
         <td style="vertical-align: middle; text-align: left; ">[https://wiki.teltonika-gps.com/view/Codec#Codec_8_Extended Codec 8 Extended]</td>
     </tr>
     </tr>
<tr>
<tr>
         <th rowspan="1" style="width:15%; vertical-align: middle; text-align: left;">Interface</th>
         <th rowspan="1" style="width:15%; vertical-align: middle; text-align: left;">Features</th>
         <th rowspan="1" style="width:35%; vertical-align: middle; text-align: left;"></th>
         <th rowspan="1" style="width:35%; vertical-align: middle; text-align: left;"></th>
     </tr>
     </tr>
     <tr>
     <tr>
         <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Digital Inputs</th>
         <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Sensors</th>
         <td style="vertical-align: middle; text-align: left; ">1</td>
         <td style="vertical-align: middle; text-align: left; ">Accelerometer</td>
     </tr>
     </tr>
     <tr>
     <tr>
         <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Digital Outputs</th>
         <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Scenarios</th>
         <td style="vertical-align: middle; text-align: left; ">2</td>
         <td style="vertical-align: middle; text-align: left; ">Crash Detection, Over Speeding, Trip, Odometer, Eco Driving, Excessive idling, Network Jamming Detection, Unplug Detection, Auto Geofence, Towing Detection, Static Navigation, Custom Scenario </td>
     </tr>
     </tr>
     <tr>
     <tr>
         <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Analog Inputs</th>
         <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Sleep modes</th>
         <td style="vertical-align: middle; text-align: left; ">1</td>
         <td style="vertical-align: middle; text-align: left; ">[https://wiki.teltonika-gps.com/view/FTC305_Sleep_modes Online sleep, Deep sleep, Power off sleep]</td>
     </tr>
     </tr>
     <tr>
     <tr>
         <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">1-Wire</th>
         <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Configuration and firmware update</th>
         <td style="vertical-align: middle; text-align: left; ">1</td>
         <td style="vertical-align: middle; text-align: left; ">[https://wiki.teltonika-gps.com/view/FOTA_WEB FOTA WEB], [https://wiki.teltonika-gps.com/view/Telematics_Configuration_Tool_(TCT) Telematics Configuration Tool (TCT)]</td>
     </tr>
     </tr>
     <tr>
     <tr>
         <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">CAN</th>
         <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">SMS</th>
         <td style="vertical-align: middle; text-align: left; ">1</td>
         <td style="vertical-align: middle; text-align: left; ">Configuration, Debug</td>
     </tr>
     </tr>
     <tr>
     <tr>
         <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">GNSS antenna</th>
         <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">GPRS commands</th>
         <td style="vertical-align: middle; text-align: left; ">Internal High Gain</td>
         <td style="vertical-align: middle; text-align: left; ">Configuration, Debug</td>
     </tr>
     </tr>
     <tr>
     <tr>
         <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">GSM antenna</th>
         <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Time Synchronization</th>
         <td style="vertical-align: middle; text-align: left; ">Internal High Gain</td>
         <td style="vertical-align: middle; text-align: left; ">GNSS, NTP, NITZ</td>
     </tr>
     </tr>
     <tr>
     <tr>
         <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">USB</th>
         <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Ignition detection</th>
         <td style="vertical-align: middle; text-align: left; ">2.0 USB Type-C</td>
         <td style="vertical-align: middle; text-align: left; ">Accelerometer, External Power Voltage</td>
     </tr>
     </tr>
     <tr>
     <tr>
         <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">LED indication</th>
         <th rowspan="1" style="width:15%; vertical-align: middle; text-align: left;">Certification & approvals</th>
         <td style="vertical-align: middle; text-align: left; ">2 status LED lights</td>
         <th rowspan="1" style="width:35%; vertical-align: middle; text-align: left;"></th>
     </tr>
     </tr>
     <tr>
     <tr>
         <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">SIM</th>
         <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Regulatory</th>
         <td style="vertical-align: middle; text-align: left; ">Nano-SIM</td>
         <td style="vertical-align: middle; text-align: left; ">-</td>
     </tr>
     </tr>
    <tr>
</table>
         <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Memory</th>
 
         <td style="vertical-align: middle; text-align: left; ">128MB internal flash memory</td>
| FTC800 =
<table class="nd-othertables_2" style="width:90%;">
<tr>
         <th rowspan="1" style="width:30%; vertical-align: middle; text-align: left;">Product</th>
         <th rowspan="1" style="width:60%; vertical-align: middle; text-align: left;"></th>
     </tr>
     </tr>
  <tr>
<tr>
         <th rowspan="1" style="width:15%; vertical-align: middle; text-align: left;">Physical Specification</th>
         <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Name</th>
         <th rowspan="1" style="width:35%; vertical-align: middle; text-align: left;"></th>
         <td style="vertical-align: middle; text-align: left; ">'''FTC800-QJAB0'''</td>
     </tr>
     </tr>
    <tr>
<tr>
         <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Dimensions</th>
<tr>
         <td style="vertical-align: middle; text-align: left; ">69 x 41 x 20.9 mm (L x W x H)</td>
         <th rowspan="1" style="width:30%; vertical-align: middle; text-align: left;">Module</th>
         <th rowspan="1" style="width:60%; vertical-align: middle; text-align: left;"></th>
     </tr>
     </tr>
    <tr>
<tr>
         <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Weight</th>
         <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Name</th>
         <td style="vertical-align: middle; text-align: left; ">76.8 g</td>
         <td style="vertical-align: middle; text-align: left; ">'''FTC800-QJAB0:''' Quectel EG915U-EU with AG3335 </td>
     </tr>
     </tr>
  <tr>
  <tr>
         <th rowspan="1" style="width:15%; vertical-align: middle; text-align: left;">Operating Environment</th>
        <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Technology</th>
        <td style="vertical-align: middle; text-align: left; ">LTE CAT 1/GSM/GPRS/GNSS</td>
    </tr>
    <tr>
         <th rowspan="1" style="width:15%; vertical-align: middle; text-align: left;">GNSS</th>
         <th rowspan="1" style="width:35%; vertical-align: middle; text-align: left;"></th>
         <th rowspan="1" style="width:35%; vertical-align: middle; text-align: left;"></th>
     </tr>
     </tr>
     <tr>
     <tr>
         <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Operating temperature</th>
         <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">GNSS</th>
         <td style="vertical-align: middle; text-align: left; ">-30 °C to +85 °C</td>
         <td style="vertical-align: middle; text-align: left; ">GPS, GLONASS, GALILEO, BEIDOU</td>
     </tr>
     </tr>
     <tr>
     <tr>
         <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Storage temperature</th>
         <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Receiver</th>
         <td style="vertical-align: middle; text-align: left; ">-30 °C to +85 °C</td>
         <td style="vertical-align: middle; text-align: left; ">L1: 75 channel</td>
     </tr>
     </tr>
     <tr>
     <tr>
         <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Operating humidity</th>
         <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Tracking sensitivity</th>
         <td style="vertical-align: middle; text-align: left; ">65 ± 20% non-condensing</td>
         <td style="vertical-align: middle; text-align: left; ">-165 dBm</td>
     </tr>
     </tr>
     <tr>
     <tr>
         <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Ingress protection rating</th>
         <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Position Accuracy</th>
         <td style="vertical-align: middle; text-align: left; ">IP67</td>
         <td style="vertical-align: middle; text-align: left; ">< 1.8 m CEP</td>
     </tr>
     </tr>
     <tr>
     <tr>
         <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Battery charge
         <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Velocity Accuracy</th>
temperature</th>
         <td style="vertical-align: middle; text-align: left; ">< 0.1 m/s (within +/- 15% error)</td>
         <td style="vertical-align: middle; text-align: left; ">0 °C to +45 °C</td>
     </tr>
     </tr>
     <tr>
     <tr>
         <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Battery discharge temperature</th>
         <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Hot start</th>
         <td style="vertical-align: middle; text-align: left; ">-20 °C to +60 °C</td>
        <td style="vertical-align: middle; text-align: left; ">-</td>
    </tr>
    <tr>
        <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Warm start</th>
         <td style="vertical-align: middle; text-align: left; ">-</td>
     </tr>
     </tr>
     <tr>
     <tr>
         <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Battery storage
         <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Hot start</th>
conditions</th>
        <td style="vertical-align: middle; text-align: left; ">-</td>
         <td style="vertical-align: middle; text-align: left; ">-10 °C to +25 °C for 3 or more months</td>
    </tr>
        <th rowspan="1" style="width:15%; vertical-align: middle; text-align: left;">Cellular</th>
        <th rowspan="1" style="width:35%; vertical-align: middle; text-align: left;"></th>
        <tr>
        <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Technology</th>
        <td style="vertical-align: middle; text-align: left; ">LTE CAT 1/GSM</td>
    </tr>
    <tr>
        <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">2G bands</th>
         <td style="vertical-align: middle; text-align: left; ">'''FTC800-QJAB0:''' GSM: B2/B3/B5/B8 </td>
    </tr>
    <tr>
        <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">4G bands</th>
        <td style="vertical-align: middle; text-align: left; "> '''FTC800-QJAB0:''' LTE FDD (CAT 1): B1/B3/B5/B7/B8/B20/B28 </td>
    </tr>
    <tr>
        <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Data transfer</th>
        <td style="vertical-align: middle; text-align: left; ">LTE FDD (CAT 1): Max. 10 Kbps (DL) / Max. 5 Kbps (UL) <br>GSM (GPRS): Max. 85.6 Kbps (DL) / Max. 85.6 Kbps (UL)</td>
    </tr>
    <tr>
        <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Transmit power</th>
        <td style="vertical-align: middle; text-align: left; ">Class 5 for GSM850/900: 30±5dBm Class 3 for GSM1800/1900: 29±5dBm <br> Class 3 for LTE-FDD: 26±5dBm</td>
    </tr>
    <tr>
        <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Data support</th>
        <td style="vertical-align: middle; text-align: left; ">SMS (TEXT, PDU), Network protocols (TCP, UDP)</td>
     </tr>
     </tr>
<tr>
<tr>
         <th rowspan="1" style="width:15%; vertical-align: middle; text-align: left;">Data Codec</th>
         <th rowspan="1" style="width:15%; vertical-align: middle; text-align: left;">Power</th>
         <th rowspan="1" style="width:35%; vertical-align: middle; text-align: left;"></th>
         <th rowspan="1" style="width:35%; vertical-align: middle; text-align: left;"></th>
     </tr>
     </tr>
     <tr>
     <tr>
         <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Codec support</th>
         <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Input voltage range</th>
         <td style="vertical-align: middle; text-align: left; ">[https://wiki.teltonika-gps.com/view/Codec#Codec_8_Extended Codec 8 Extended]</td>
         <td style="vertical-align: middle; text-align: left; ">10 - 30 V DC</td>
     </tr>
     </tr>
<tr>
    <tr>
        <th rowspan="1" style="width:15%; vertical-align: middle; text-align
        <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Back-up battery</th>
        <td style="vertical-align: middle; text-align: left; ">100mAh Li-Ion battery 3.7V (0.37 Wh) </td>
    </tr>
    <tr>
        <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Internal fuse</th>
        <td style="vertical-align: middle; text-align: left; ">3A</td>
    </tr>
    <tr>
        <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Power Consumption</th>
        <td style="vertical-align: middle; text-align: left; "> TBA </td>
    </tr>
<tr>
        <th rowspan="1" style="width:15%; vertical-align: middle; text-align: left;">Interface</th>
        <th rowspan="1" style="width:35%; vertical-align: middle; text-align: left;"></th>
    </tr>
    <tr>
        <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">GNSS antenna</th>
        <td style="vertical-align: middle; text-align: left; ">Internal High Gain </td>
    </tr>
    <tr>
        <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">GSM antenna</th>
        <td style="vertical-align: middle; text-align: left; ">Internal High Gain </td>
    </tr>
    <tr>
        <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">USB</th>
        <td style="vertical-align: middle; text-align: left; ">2.0 USB Type-C</td>
    </tr>
    <tr>
        <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">LED indication</th>
        <td style="vertical-align: middle; text-align: left; ">2 status LED lights</td>
    </tr>
    <tr>
        <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">SIM</th>
        <td style="vertical-align: middle; text-align: left; ">Nano-SIM</td>
    </tr>
    <tr>
        <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Memory</th>
        <td style="vertical-align: middle; text-align: left; ">128MB internal flash memory</td>
    </tr>
  <tr>
        <th rowspan="1" style="width:15%; vertical-align: middle; text-align: left;">Physical Specification</th>
        <th rowspan="1" style="width:35%; vertical-align: middle; text-align: left;"></th>
    </tr>
    <tr>
        <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Dimensions</th>
        <td style="vertical-align: middle; text-align: left; ">TBA</td>
    </tr>
    <tr>
        <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Weight</th>
        <td style="vertical-align: middle; text-align: left; ">TBA</td>
    </tr>
<tr>
        <th rowspan="1" style="width:15%; vertical-align: middle; text-align: left;">Operating Environment</th>
        <th rowspan="1" style="width:35%; vertical-align: middle; text-align: left;"></th>
    </tr>
    <tr>
        <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Operating temperature (without battery)</th>
        <td style="vertical-align: middle; text-align: left; ">-30 °C to +85 °C</td>
    </tr>
    <tr>
        <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Storage temperature (without battery)</th>
        <td style="vertical-align: middle; text-align: left; ">-30 °C to +85 °C</td>
    </tr>
    <tr>
        <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Operating temperature (with battery)</th>
        <td style="vertical-align: middle; text-align: left; ">0 °C to +45 °C</td>
    </tr>
    <tr>
        <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Storage temperature (with battery)</th>
        <td style="vertical-align: middle; text-align: left; ">-20 °C to +45 °C for 1 month <br> -20 °C to +35 °C for 6 months</td>
    </tr>
    <tr>
        <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Operating humidity</th>
        <td style="vertical-align: middle; text-align: left; ">5% to 95% non-condensing</td>
    </tr>
    <tr>
        <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Ingress protection rating</th>
        <td style="vertical-align: middle; text-align: left; ">IP41</td>
    </tr>
    <tr>
        <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Battery charge
temperature</th>
        <td style="vertical-align: middle; text-align: left; ">0 °C to +45 °C</td>
    </tr>
    <tr>
        <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Battery discharge temperature</th>
        <td style="vertical-align: middle; text-align: left; ">-20 °C to +60 °C</td>
    </tr>
    <tr>
        <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Battery storage
conditions</th>
        <td style="vertical-align: middle; text-align: left; ">-10 °C to +50 °C for 1 month<br> -10 °C to +35 °C for 3 months<br> 0 °C to +30 °C for 1 year </td>
    </tr>
<tr>
        <th rowspan="1" style="width:15%; vertical-align: middle; text-align: left;">Data Codec</th>
        <th rowspan="1" style="width:35%; vertical-align: middle; text-align: left;"></th>
    </tr>
    <tr>
        <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Codec support</th>
        <td style="vertical-align: middle; text-align: left; ">[https://wiki.teltonika-gps.com/view/Codec#Codec_8_Extended Codec 8 Extended]</td>
    </tr>
<tr>
        <th rowspan="1" style="width:15%; vertical-align: middle; text-align: left;">Features</th>
        <th rowspan="1" style="width:35%; vertical-align: middle; text-align: left;"></th>
    </tr>
    <tr>
        <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Sensors</th>
        <td style="vertical-align: middle; text-align: left; ">Accelerometer</td>
    </tr>
    <tr>
        <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Scenarios</th>
        <td style="vertical-align: middle; text-align: left; ">Crash Detection, Over Speeding, Trip, Odometer, Eco Driving, Excessive idling, Network Jamming Detection, Unplug Detection, Auto Geofence, Towing Detection, Static Navigation, Custom Scenario </td>
    </tr>
    <tr>
        <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Sleep modes</th>
        <td style="vertical-align: middle; text-align: left; ">[https://wiki.teltonika-gps.com/view/FTC305_Sleep_modes Online sleep, Deep sleep, Power off sleep]</td>
    </tr>
    <tr>
        <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Configuration and firmware update</th>
        <td style="vertical-align: middle; text-align: left; ">[https://wiki.teltonika-gps.com/view/FOTA_WEB FOTA WEB], [https://wiki.teltonika-gps.com/view/Telematics_Configuration_Tool_(TCT) Telematics Configuration Tool (TCT)]</td>
    </tr>
    <tr>
        <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">SMS</th>
        <td style="vertical-align: middle; text-align: left; ">Configuration, Debug</td>
    </tr>
    <tr>
        <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">GPRS commands</th>
        <td style="vertical-align: middle; text-align: left; ">Configuration, Debug</td>
    </tr>
    <tr>
        <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Time Synchronization</th>
        <td style="vertical-align: middle; text-align: left; ">GNSS, NTP, NITZ</td>
    </tr>
    <tr>
        <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Ignition detection</th>
        <td style="vertical-align: middle; text-align: left; ">Accelerometer, External Power Voltage</td>
    </tr>
    <tr>
        <th rowspan="1" style="width:15%; vertical-align: middle; text-align: left;">Certification & approvals</th>
        <th rowspan="1" style="width:35%; vertical-align: middle; text-align: left;"></th>
    </tr>
    <tr>
        <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Regulatory</th>
        <td style="vertical-align: middle; text-align: left; ">-</td>
    </tr>
</table>
 
| FTM887 =
<table class="nd-othertables_2" style="width:90%;">
<tr>
        <th rowspan="1" style="width:30%; vertical-align: middle; text-align: left;">Module</th>
        <th rowspan="1" style="width:60%; vertical-align: middle; text-align: left;"></th>
    </tr>
<tr>
        <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Name</th>
        <td style="vertical-align: middle; text-align: left; ">'''FTM887-Q2AB0:''' Quectel BG95-M1 with AG3335 <br> F'''TM887-Q3AB0:''' Quectel BG95-M3 with AG3335 <br> '''FTM887-Q5AB0:''' Quectel BG95-M6 with AG333
<br>  </td>
    </tr>
<tr>
        <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Technology</th>
        <td style="vertical-align: middle; text-align: left; ">LTE CAT M1/NB-IoT/GPRS/GNSS</td>
    </tr>
    <tr>
        <th rowspan="1" style="width:15%; vertical-align: middle; text-align: left;">GNSS</th>
        <th rowspan="1" style="width:35%; vertical-align: middle; text-align: left;"></th>
    </tr>
    <tr>
        <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">GNSS</th>
        <td style="vertical-align: middle; text-align: left;


}}
}}
<!-- TBD
}}
=='''ELECTRICAL CHARACTERISTICS'''==
-->
[[Category:{{{model}}}]]
[[Category:{{{model}}}]]

Latest revision as of 14:49, 16 March 2026

[[Image:{{{model}}} side.png|thumb|400x300px|right|upright=0.35|{{{model}}}]]

KNOW YOUR DEVICE

[[Image:{{{model}}} know your device.png|400px]]

SET UP YOUR DEVICE

 Physical SIM card insertion/removal must be performed when device is powered off – external voltage disconnected. Otherwise, the SIM card might be damaged or device will not detect it.

[[Image:{{{model}}} setup.png|1000px|left]]

HOW TO REMOVE COVER

 Device casing is designed to be water-proof and match requirements for IP69K. Please note that once the cover is fully clipped it will require additional plastic pry tools to be opened! Please make sure to review short walkthrough video for more details:
Load video
YouTube

PINOUT

PC CONNECTION (WINDOWS)

HOW TO INSTALL USB DRIVERS (WINDOWS)

  1. Please download COM port drivers from here.
  2. Extract and run TeltonikaCOMDriver.exe.
  3. Click Next in driver installation window.
  4. In the following window click Install button.
  5. Setup will continue installing the driver and eventually the confirmation window will appear. Click Finish to complete the setup.

CONFIGURATION (WINDOWS)

Most Teltonika devices are shipped with default factory settings. Use Telematics Configuration Tool (TCT) to change these settings according to your needs.

PIN NUMBER PIN NAME DESCRIPTION 
           [[Image:{{{model}}}_pinout.png|400px|center]]
TCT
Operating system Windows 10
Windows 11
MS .NET Framework version MS .NET framework 6.0
Version 64 bit
Disk Storage 1 GB of free disk space
Internet Ethernet port or Wi-Fi w/ network access for auto-update

TCT

  1. Download the TCT (compressed archive).
  2. Extract the archive and launch the executable. The TCT will be installed.
  3. Launch the TCT.
  4. In the Discovered devices list, select your device and press Configure.
  5. The Device status window opens. It contains device, GNSS and Cellular information.

Save to device – saves configuration to device.

Upload file – loads configuration from file.

Save to file – saves configuration to file.

Update – update device firmware.

Reset configuration – sets device configuration to default.


Most important configuration sections are Mobile network (Server, Mobile network settings) and Tracking settings (data collection parameters). More details about {{{model}}} configuration using TCT can be found here.

QUICK SMS CONFIGURATION

The default configuration ensures best track quality and optimal data usage.

Quickly set up your device by sending this SMS command to it:

DEFAULT CONFIGURATION SETTINGS

After successful SMS configuration, {{{model}}} device will synchronize time and update records to configured server. Time intervals and default I/O elements can be changed by using TCT or Parameter list.

MOUNTING RECOMMENDATIONS

LED INDICATIONS

This section is an explanation of LED indications on {{{model}}} device.


BASIC CHARACTERISTICS

[[Category:{{{model}}}]]

Retrieved from "https://wiki.teltonika-gps.com/index.php?title=Template:FTX_First_Start&oldid=111834"