Template:FMA2 Mounting recommendations: Difference between revisions
Created page with "<font size="+3"><span style=color:#104996>'''Mounting recommendations'''</span></font> <font size="+2"><span style=color:#F49E21> 1. </span> Connecting wires </font> <font si..." |
No edit summary |
||
| (One intermediate revision by one other user not shown) | |||
| Line 1: | Line 1: | ||
<font size="+ | <font size="+1"><span style=color:#104996>'''Mounting recommendations'''</span></font> | ||
<font size="+ | <font size="+1"><span style=color:#F49E21> 1. </span> Connecting wires </font> | ||
<font size="+1"> | <font size="+1"> | ||
* Wires should be connected while the module is not plugged in. | * Wires should be connected while the module is not plugged in. | ||
| Line 9: | Line 9: | ||
* Wires cannot be connected to the board computers or control units. | * Wires cannot be connected to the board computers or control units. | ||
</font> | </font> | ||
<font size="+ | <font size="+1"><span style=color:#F49E21> 2. </span> Connecting power source. </font> | ||
<font size="+1"> | <font size="+1"> | ||
* Be sure that after the car computer goes to sleep mode, power might be still available on the power wires. Depending on the car model, this may happen in 5 to 30 minutes period. | * Be sure that after the car computer goes to sleep mode, power might be still available on the power wires. Depending on the car model, this may happen in 5 to 30 minutes period. | ||
| Line 16: | Line 16: | ||
* 3 A, 125 V external fuse shall be used. | * 3 A, 125 V external fuse shall be used. | ||
</font> | </font> | ||
<font size="+ | <font size="+1"><span style=color:#F49E21> 3. </span> Connecting ignition wire. </font> | ||
<font size="+1"> | <font size="+1"> | ||
* Be sure to check if it is a real ignition wire i. e. power does not disappear after starting the engine. | * Be sure to check if it is a real ignition wire i. e. power does not disappear after starting the engine. | ||
| Line 23: | Line 23: | ||
* Ignition is connected to the ignition relay output. As alternative, any other relay, which has power output when ignition is on, may be chosen. | * Ignition is connected to the ignition relay output. As alternative, any other relay, which has power output when ignition is on, may be chosen. | ||
</font> | </font> | ||
<font size="+ | <font size="+1"><span style=color:#F49E21> 4. </span> Connecting ground wire. </font> | ||
<font size="+1"> | <font size="+1"> | ||
* Ground wire is connected to the vehicle frame or metal parts that are fixed to the frame. | * Ground wire is connected to the vehicle frame or metal parts that are fixed to the frame. | ||
| Line 30: | Line 30: | ||
</font><br /> | </font><br /> | ||
<font size="+ | <font size="+1"><span style=color:#104996>'''{{{model|FMB2YX}}} installation instruction'''</span></font><br> | ||
<font size="+1"> | <font size="+1"> | ||
{{ | {{ | ||
Template: | Template:FMA2YX_Installation_instruction | ||
|model={{{model|FMB2YX}}} | |model={{{model|FMB2YX}}} | ||
}} | }} | ||
| Line 56: | Line 56: | ||
<br /><br /> | <br /><br /> | ||
<font size="+ | <font size="+1"><span style=color:#FF0000>'''Safety information'''</span></font><br/> | ||
<font size="+ | <font size="+1"> | ||
This message contains information on how to operate {{{model|FMB20X}}} safely. By following these requirements and recommendations, you will avoid dangerous situations. You must read these instructions carefully and follow them strictly before operating the device!<br/> | This message contains information on how to operate {{{model|FMB20X}}} safely. By following these requirements and recommendations, you will avoid dangerous situations. You must read these instructions carefully and follow them strictly before operating the device!<br/> | ||
The device uses SELV limited power source. The device uses a 6 V...30 V DC power supply. | The device uses SELV limited power source. The device uses a 6 V...30 V DC power supply. | ||
| Line 69: | Line 69: | ||
<font size="+ | <font size="+1"><span style=color:#104996>'''Precautions'''</span></font> | ||
<font size="+ | <font size="+1"> | ||
{| class="wikitable" style="border-style: solid; border-width: 0px" | {| class="wikitable" style="border-style: solid; border-width: 0px" | ||
|+ | |+ | ||