Difference between revisions of "Upgrading CAN-CONTROL to CAN-CONTROl+Immobilizer"

From Wiki Knowledge Base | Teltonika GPS
(Created page with "Wiki. FAQ Upgrading CAN-CONTROL to CAN-CONTROl+Immobilizer Possible problems: 1. Doors Lock/Unlock is not working. 2. Doors Lock/Unlock works but engine blocking and unbloc...")
 
 
(6 intermediate revisions by 3 users not shown)
Line 1: Line 1:
−
Wiki.
+
== Struggle after upgrading CAN-CONTROL to CAN-CONTROL+Immobilizer? ==
−
FAQ
+
Possible encounters after upgrading CAN bus adapter:
  
−
Upgrading CAN-CONTROL to CAN-CONTROl+Immobilizer
+
* Vehicle doors Lock/Unlock is not working;
 +
* Vehicle doors Lock/Unlock is working but engine Blocking/Unblocking does not and after sending commands, the response is: "''CAN-CONTROL cmd not supported''".
  
−
Possible problems:
+
If You encounter with any of these issues - follow solution steps below.
  
−
1. Doors Lock/Unlock is not working.
+
== Solution ==
−
2. Doors Lock/Unlock works but engine blocking and unblock does not. Most of times response will be: CMD not supported. In some situations engine block will work but unblocking will not.
+
After installation is completed and CAN bus adapter program is set, please, follow these steps:
  
−
After installation is done and program number is set please do learning procedure.
+
# Do a learning procedure - using the vehicle key, unlock and lock vehicle '''three''' '''times''';
 +
# Send GPRS command - "  lvcansetprog 11120" (or any other). Program number must contain 5 digits.
 +
# Send GPRS command - "  lvcansetprog ''the one that is for Your vehicle model''". Program number can be seen in at the top of the CAN adapter connection scheme.
 +
# After receiving a response to a command, repeat the learning procedure (first step).
  
−
1. send lvcansetprog 11120 (Or any other)
 
−
2. send lvcansetprog (one that is for your car model)
 
−
3. After you will receive response please do learning with key locking/unlocking 3 times. lock>unlock;lock>unlock;lock>unlock;
 
  
−
Now you can try commands to open and close doors.
+
{|
−
Now you can try commands to block and unblock engine.
+
|-
 +
| [[File:Alert.png|left|link=]] || <b>'''Note''': Before SMS text, two space symbols should be inserted if no SMS username or password was set in [[FMB001 SMS/Call settings|SMS / Call settings]].
 +
After completed these steps, commands to open/close and to block/unblock engine can be performed.
 +
All SMS/GPRS responses should inform You that particular command has been completed successfully.</b>
 +
|}
  
−
All sms/gprs responces should inform you that command has been completed succesffully.
+
<bR>
−
 
+
{|
−
Note: If installing CAN-CONTROL adapter into different vehicle learning must be initiated. If adapter will be installed back on previous car model learning step must be repeated.
+
|-
 +
| [[File:Alert.png|left|link=]] || <b>'''Note''': if installing CAN-CONTROL adapter into different vehicle - program should be changed according to the vehicle model and learning must be initiated ("first solution step").  
 +
If adapter will be installed again on the previous vehicle - program number needs to be restored and learning step must be repeated.
 +
</b>
 +
|}

Latest revision as of 09:41, 22 January 2021

Struggle after upgrading CAN-CONTROL to CAN-CONTROL+Immobilizer?

Possible encounters after upgrading CAN bus adapter:

  • Vehicle doors Lock/Unlock is not working;
  • Vehicle doors Lock/Unlock is working but engine Blocking/Unblocking does not and after sending commands, the response is: "CAN-CONTROL cmd not supported".

If You encounter with any of these issues - follow solution steps below.

Solution

After installation is completed and CAN bus adapter program is set, please, follow these steps:

  1. Do a learning procedure - using the vehicle key, unlock and lock vehicle three times;
  2. Send GPRS command - " lvcansetprog 11120" (or any other). Program number must contain 5 digits.
  3. Send GPRS command - " lvcansetprog the one that is for Your vehicle model". Program number can be seen in at the top of the CAN adapter connection scheme.
  4. After receiving a response to a command, repeat the learning procedure (first step).


Alert.png
 Note: Before SMS text, two space symbols should be inserted if no SMS username or password was set in SMS / Call settings.

After completed these steps, commands to open/close and to block/unblock engine can be performed. All SMS/GPRS responses should inform You that particular command has been completed successfully.


Alert.png
 Note: if installing CAN-CONTROL adapter into different vehicle - program should be changed according to the vehicle model and learning must be initiated ("first solution step").

If adapter will be installed again on the previous vehicle - program number needs to be restored and learning step must be repeated.

Retrieved from "https://wiki.teltonika-gps.com/index.php?title=Upgrading_CAN-CONTROL_to_CAN-CONTROl%2BImmobilizer&oldid=62109"