Difference between revisions of "Upgrading CAN-CONTROL to CAN-CONTROl+Immobilizer"
From Wiki Knowledge Base | Teltonika GPS
| (2 intermediate revisions by the same user not shown) | |||
| Line 5: | Line 5: | ||
* Vehicle doors Lock/Unlock is working but engine Blocking/Unblocking does not and after sending commands, the response is: "''CAN-CONTROL cmd not supported''". | * Vehicle doors Lock/Unlock is working but engine Blocking/Unblocking does not and after sending commands, the response is: "''CAN-CONTROL cmd not supported''". | ||
| − | If You encounter with any of these issues - | + | If You encounter with any of these issues - follow solution steps below. |
== Solution == | == Solution == | ||
| − | After installation is | + | After installation is completed and CAN bus adapter program is set, please, follow these steps: |
# Do a learning procedure - using the vehicle key, unlock and lock vehicle '''three''' '''times'''; | # Do a learning procedure - using the vehicle key, unlock and lock vehicle '''three''' '''times'''; | ||
| Line 15: | Line 15: | ||
# After receiving a response to a command, repeat the learning procedure (first step). | # After receiving a response to a command, repeat the learning procedure (first step). | ||
| − | |||
| + | {| | ||
| + | |- | ||
| + | | [[File:Alert.png|left|link=]] || <b>'''Note''': Before SMS text, two space symbols should be inserted if no SMS username or password was set in [[FMB001 SMS/Call settings|SMS / Call settings]]. | ||
After completed these steps, commands to open/close and to block/unblock engine can be performed. | After completed these steps, commands to open/close and to block/unblock engine can be performed. | ||
| + | All SMS/GPRS responses should inform You that particular command has been completed successfully.</b> | ||
| + | |} | ||
| − | + | <bR> | |
| − | + | {| | |
| − | '''Note''': if installing CAN-CONTROL adapter into different vehicle - program should be changed according to the vehicle model and learning must be initiated ("first solution step"). If adapter will be installed again on the previous vehicle - program number needs to be restored and learning step must be repeated. | + | |- |
| + | | [[File:Alert.png|left|link=]] || <b>'''Note''': if installing CAN-CONTROL adapter into different vehicle - program should be changed according to the vehicle model and learning must be initiated ("first solution step"). | ||
| + | If adapter will be installed again on the previous vehicle - program number needs to be restored and learning step must be repeated. | ||
| + | </b> | ||
| + | |} | ||
Latest revision as of 09:41, 22 January 2021
Struggle after upgrading CAN-CONTROL to CAN-CONTROL+Immobilizer?
Possible encounters after upgrading CAN bus adapter:
- Vehicle doors Lock/Unlock is not working;
- Vehicle doors Lock/Unlock is working but engine Blocking/Unblocking does not and after sending commands, the response is: "CAN-CONTROL cmd not supported".
If You encounter with any of these issues - follow solution steps below.
Solution
After installation is completed and CAN bus adapter program is set, please, follow these steps:
- Do a learning procedure - using the vehicle key, unlock and lock vehicle three times;
- Send GPRS command - " lvcansetprog 11120" (or any other). Program number must contain 5 digits.
- Send GPRS command - " lvcansetprog the one that is for Your vehicle model". Program number can be seen in at the top of the CAN adapter connection scheme.
- After receiving a response to a command, repeat the learning procedure (first step).
 |
Note: Before SMS text, two space symbols should be inserted if no SMS username or password was set in SMS / Call settings.
After completed these steps, commands to open/close and to block/unblock engine can be performed. All SMS/GPRS responses should inform You that particular command has been completed successfully. |
|
Note: if installing CAN-CONTROL adapter into different vehicle - program should be changed according to the vehicle model and learning must be initiated ("first solution step").
If adapter will be installed again on the previous vehicle - program number needs to be restored and learning step must be repeated. |
