Difference between revisions of "FTC921 System"

From Wiki Knowledge Base | Teltonika GPS
(Replaced content with "{{template:FTX88X/FTX9XX System|model=FTC921}}")
Tag: Replaced
 
(10 intermediate revisions by one other user not shown)
Line 1: Line 1:
−
==Ignition settings==
+
{{template:FTX88X/FTX9XX System|model=FTC921}}
−
[[File:FTC921_Ignition_settings.png|right|300 px]]
 
−
Ignition source will be used to determine ignition of vehicle.
 
−
 
 
−
{{{ignition_source|Possible ignition sources:
 
−
{{{txt_din1|* '''DIN 1''' (Digital Input 1) - if ''DIN1'' is 1 - ignition is ON; if ''DIN1'' value is 0 - ignition is OFF;}}}
 
−
* '''Power Voltage''' - if voltage is between High Voltage Level and Low Voltage Level (below ''Ignition Settings'' options) - ignition is ON; if voltage is higher than High Voltage Level or lower than Low Voltage Level - ignition is OFF.
 
−
 
 
−
* '''Accelerometer''' - if movement sensor detects movement - ignition is ON; if movement is not detected - ignition is OFF;
 
−
More than one ignition source can be selected at the same moment. When there are 2 or more sources selected, at least one condition has to be met to change Ignition status.<br>
 
−
 
 
−
{{{txt_example|'''Example:''' DIN1 and Accelerometer are selected as the Ignition source. When the device detects movement, Ignition status will change to 1, regardless that DIN1 value is 0. Users can select movement start and movement stop delay time - those parameters are used when the accelerometer is selected as an ignition source. }}}}}}
 
−
Ignition status is used in power management and the following functionalities: [[{{{model|FMB1YX}}} Features settings#Eco/Green Driving|Eco/Green Driving]], [[{{{model|FMB1YX}}} Accelerometer Features settings#Excessive Idling|Excessive Idling]], Fuel Consumption, [[{{{model|FMB1YX}}} Features settings#Over Speeding|Over Speeding]], [[{{{model|FMB1YX}}} Accelerometer Features settings#Towing Detection|Towing Detection]] and [[{{{model|FMB1YX}}} Trip/Odometer settings|Trip]].<br>
 
−
<!--'''Note:''' Object motion detection settings, where user can configure {{{txt_num|4}}} ways how {{{model|FMB1YX}}} detects movement and change its working mode (for more information refer to section {{{ctrDaq|[[{{{model|Template:}}} Data acquisition settings]]}}}). Other functionalities that depend on movement source are: power manager, fuel consumption and trip;}}}-->
 
−
 
 
−
 
 
−
 
 
−
==Movement settings==
 
−
[[File:FTC921_Movement_settings.png|right|300 px]]
 
−
Movement source will be used to determine when a vehicle is on stop or moving.<br>
 
−
Possible movement sources:
 
−
* '''Ignition''' - if ignition (based on ignition source) is ON, Vehicle MOVING mode is used; if the ignition is OFF, Vehicle on STOP mode is used;
 
−
* '''Accelerometer''' (movement) - if accelerometer detects movement, Vehicle MOVING mode is used; if there is no movement detected, Vehicle on STOP mode is used;
 
−
* '''GNSS''' - if GPS fix is acquired and speed >= 5 km/h vehicle MOVING mode is used; if GPS speed <5 km/h, Vehicle on STOP mode is used;
 

Latest revision as of 09:40, 7 September 2023

Ignition settings

FTC ignition resized.gif

Ignition source will be used to determine the ignition status of the vehicle.

Possible ignition sources:

DIN 1 (Digital Input 1) - if DIN1 is 1 - ignition is ON; if DIN1 value is 0 - ignition is OFF

Power Voltage - if the voltage is between High Voltage Level and Low Voltage Level (below Ignition Settings options) - ignition is ON; if the voltage is higher than High Voltage Level or lower than Low Voltage Level - ignition is OFF.

Accelerometer - if movement sensor detects movement - ignition is ON; if movement is not detected - ignition is OFF;

More than one ignition source can be selected at the same time. Note: When there are 2 or more sources selected, at least one condition has to be met to change Ignition status.
For Example, if both accelerometer and power voltage are selected, only one of the ignition detection conditions have to be true for ignition to be detected.

Ignition status is used in power management and the following functionalities: Over Speeding, Trip and Odometer settings.

Movement settings

TCT-Movement-1.png

Movement source will be used to determine when a vehicle is on stop or moving.
Possible movement sources:

  • Accelerometer (movement) - if the accelerometer detects movement, the Vehicle is under MOVING mode; if there is no movement detected, the Vehicle on STOP mode;
  • GNSS - if GPS fix is acquired and speed >= 5 km/h vehicle then the MOVING mode is used; if GPS speed <5 km/h, the Vehicle on STOP mode is used;
  • Power voltage - Data acquisition > "moving" mode (Parameter state = 1) - when power voltage is >= low power voltage and <= high power voltage. By default low voltage is 13.2 V and the high voltage is 30 V;
  • DIN 1 - Data acquisition > "moving" mode (Parameter state = 1) - when voltage measured by DIN 1 is higher than 7.5V. Data acquisition > "on stop" mode (Parameter state = 0) - when voltage measured by DIN 1 is lower than 7.5V.






Configuration password

Configuration password.png

Protects the device from unauthorized access while using USB or Bluetooth to make any form of configuration changes.

  • Set password - Set the primary password for the device. Required to access the device every time using the USB or via Bluetooth connection.
  • Recovery password (optional) - in the event that the primary password is forgotten, the recovery password can be used as a backup to unlock the device configuration.













GNSS settings

In GNSS Source settings user can configure which GNSS system(s) to use.

FTC GNSS Settings.png

List of configurable GNSS sources:

  • GPS
  • GPS + GLONASS
  • GPS + Galileo
  • GPS + BeiDou
  • GPS + GLONASS + Galileo + BeiDou



Movement delay

Movement Delays.png

Movement delay will be used to set the timeout of delays when the accelerometer status changes.

Note: These settings impact the ignition/movement sources.
The user can set:

  • Movement start delay (s) - movement start delay in seconds;
  • Movement stop delay (s) - movement stop delay in seconds;





Power Saving settings

Power Saving Settings.png

Puts the device into a power-saving mode, preserving the power consumption from the external source or the internal battery. The device enters this mode after the conditions are met.

  • The selectable modes are as follows:

Disable - Normal mode, no internal battery saving.

Ultra Deep Sleep - The device turns off almost everything to save maximum power. The device exits this mode when DIN turns 1 (ON).

  • Timeout - After timeout is reached, and conditions are met for the sleep mode, the device goes into sleep mode.




Time synchronization settings

FTC921 Time synchronization settings.png

NTP Resync parameter determines how often a device should resynchronize its time. If the set value is not equal to zero, time resynchronization will occur periodically at time intervals to which this parameter is set.
NTP server 1 and NTP Server 2 let the user select which NTP server (s) will be used to re-synchronize time.




Time synchronization works by waiting a minute on startup to acquire fix and consequently synchronizes the time via GNSS.
This state checks the difference between RTC and GNSS times every second. If the difference of at least 3 seconds persists to be for 5 seconds, the firmware triggers a re-synchronization procedure by GNSS.
After that, the time difference is still calculated, but the difference is expected to persist for at least 5 minutes to trigger a GNSS time re-synchronization.
In the case that there is no fix or it is lost during the syncing by GNSS state, the firmware goes to the state of syncing by NTP. Entering the state of NTP syncing, the firmware immediately attempts to synchronize the time by triggering NTP and later on, does this periodically every time the configured NTP re-synchronization time is reached (if the re-synchronization time is set to 0 – no NTP sync is performed at all). Time synchronization by NITZ can occur at any time.

Lentele.png

Lenta.png


Battery settings

FTC battery settings resized.gif

Battery settings allow selecting battery charge modes.

Possible charge modes:

On need—Battery will charge on need
After ignition ON—Battery will start charging when the ignition source is turned ON
Always—Battery will charge all the time







LED settings

FTC led settings.png



This feature allows disabling or enabling status and navigation LED's

Retrieved from "https://wiki.teltonika-gps.com/index.php?title=FTC921_System&oldid=88883"