Difference between revisions of "Template:System settings"

From Wiki Knowledge Base | Teltonika GPS
m
 
(19 intermediate revisions by 2 users not shown)
Line 1: Line 1:
 
==System Settings==
 
==System Settings==
−
{|
+
 
 
{{#if:{{{MM_Movement_source|}}}
 
{{#if:{{{MM_Movement_source|}}}
 
|
 
|
Line 6: Line 6:
 
User can select which source will be used to determine when vehicle is on stop or moving. When multiple are selected, if any of selected are active, Vehicle MOVING mode is used.
 
User can select which source will be used to determine when vehicle is on stop or moving. When multiple are selected, if any of selected are active, Vehicle MOVING mode is used.
 
Available movement source:
 
Available movement source:
−
[[Image:Screenshot 2024-03-01 at 14-04-10 5.2. System - Mobility documentation.png|right|300px]]
+
[[Image:Screenshot 2024-03-01 at 14-04-10 5.2. System - Mobility documentation.png|right]]
 
* Ignition: checks ignition settings which depends on Ignition Source settings;
 
* Ignition: checks ignition settings which depends on Ignition Source settings;
  
Line 15: Line 15:
 
* CAN Speed: movement is detected if CAN speed retrieved from specific CAN protocol.
 
* CAN Speed: movement is detected if CAN speed retrieved from specific CAN protocol.
  
−
When multiple source are selected, if any of selected are active, Movemenet is detected.
+
When multiple source are selected, if any of selected are active, Movement is detected.
  
  
  
 
}}
 
}}
−
|}
 
  
−
{|
 
 
{{#if:{{{TFT_can|}}}
 
{{#if:{{{TFT_can|}}}
 
|
 
|
Line 34: Line 32:
 
[[Image:Screenshot 2024-03-01 at 14-09-53 5.2. System - Mobility documentation.png]]
 
[[Image:Screenshot 2024-03-01 at 14-09-53 5.2. System - Mobility documentation.png]]
 
}}
 
}}
−
|}
 
  
−
{|
 
 
{{#if:{{{AT_no_show|}}}
 
{{#if:{{{AT_no_show|}}}
 
|
 
|
Line 45: Line 41:
 
* <b>Always</b> - Always save/send records. Allows record sending with no coordinates and no correct time.
 
* <b>Always</b> - Always save/send records. Allows record sending with no coordinates and no correct time.
 
}}
 
}}
−
|}
 
  
−
{|
+
{{#if:{{{TFT_show|}}}
−
{{#if:{{{TFT_system_settings|}}}
 
 
|
 
|
 
|===PDOP filter===
 
|===PDOP filter===
Line 54: Line 48:
 
* <b>PDOP filter threshold</b> - PDOP filter threshold value can be entered from which the parameters will be filtered.
 
* <b>PDOP filter threshold</b> - PDOP filter threshold value can be entered from which the parameters will be filtered.
 
}}
 
}}
−
|}
 
  
−
{|
+
{{#if:{{{TFT_show|}}}
−
{{#if:{{{TFT_system_settings|}}}
 
 
|
 
|
 
|===Input/Output Mode===
 
|===Input/Output Mode===
Line 66: Line 58:
 
*Digital output 1 and Digital output 2 (value:10).
 
*Digital output 1 and Digital output 2 (value:10).
 
}}
 
}}
−
|}
 
  
−
{|
 
 
{{#if:{{{MM_LED_indication|}}}
 
{{#if:{{{MM_LED_indication|}}}
 
|
 
|
Line 74: Line 64:
 
User can turn on or off the indication LEDs.
 
User can turn on or off the indication LEDs.
 
}}
 
}}
−
|}
 
−
 
  
−
{|
 
 
{{#if:{{{AT_no_show|}}}
 
{{#if:{{{AT_no_show|}}}
 
|
 
|
Line 98: Line 85:
  
 
}}
 
}}
−
|}
 
  
−
{|
 
 
{{#if:{{{TST_battery_charge_mode|}}}
 
{{#if:{{{TST_battery_charge_mode|}}}
 
|
 
|
Line 117: Line 102:
  
 
}}
 
}}
−
|}
 
  
−
{|
+
{{#if:{{{TFT_show|}}}
−
{{#if:{{{TFT_system_settings|}}}
 
 
|
 
|
 
|===Analog Input Value Range===
 
|===Analog Input Value Range===
Line 134: Line 117:
  
 
}}
 
}}
−
|}
 
  
−
{|
+
{{#if:{{{TFT_show|}}}
−
{{#if:{{{TFT_DOUT Overcurrent protection|}}}
 
 
|
 
|
 
|===DOUT Overcurrent protection===
 
|===DOUT Overcurrent protection===
Line 143: Line 124:
  
 
}}
 
}}
−
|}
 
  
−
{|
 
 
{{#if:{{{Data_protocol|}}}
 
{{#if:{{{Data_protocol|}}}
 
|
 
|
Line 152: Line 131:
 
*Codec 8 supports up to 255 AVL ID;
 
*Codec 8 supports up to 255 AVL ID;
 
*Codec 8 Extended supports up and above 255 AVL ID.
 
*Codec 8 Extended supports up and above 255 AVL ID.
−
 
 
}}
 
}}
−
|}
 
  
−
{|
 
 
{{#if:{{{PT_Power_on|}}}
 
{{#if:{{{PT_Power_on|}}}
 
|
 
|
 
|===Power On By USB/Charger===
 
|===Power On By USB/Charger===
−
[[Image:PT Power on by usb.png|200px|right]]
+
[[Image:PT Power on by usb.png|right]]
 
'''Note''': This feature is available forwards from FW version 55.02.03.Rev.05<br>
 
'''Note''': This feature is available forwards from FW version 55.02.03.Rev.05<br>
 
Device supports two working modes: normal mode, where the device works as usual, and charging mode, which is entered when ''Power On By USB/Charger'' parameter is <b>disabled</b>. To enter normal mode, device can be turned on by power button or by USB charger, if ''Power On By USB/Charger'' parameter is set to <b>Enable</b>.
 
Device supports two working modes: normal mode, where the device works as usual, and charging mode, which is entered when ''Power On By USB/Charger'' parameter is <b>disabled</b>. To enter normal mode, device can be turned on by power button or by USB charger, if ''Power On By USB/Charger'' parameter is set to <b>Enable</b>.
  
 
}}
 
}}
−
|}
 
  
−
{|
 
 
{{#if:{{{PT_Power_on|}}}
 
{{#if:{{{PT_Power_on|}}}
 
|
 
|
 
|===Continuous Charging Mode===
 
|===Continuous Charging Mode===
−
[[Image:PT continuous charging.png|200px|right]]
+
[[Image:PT continuous charging.png|right]]
 
'''Note''': This feature is available forwards from FW version 55.02.03.Rev.05<br>
 
'''Note''': This feature is available forwards from FW version 55.02.03.Rev.05<br>
 
Battery protection mode to extend battery life. Should only be used when device is permanently connected to external charger. When enabled charge current is reduced preventing charging to maximum voltage. This results in lower battery temperature and extended battery lifetime. Please note, this also increases battery charge time and reduces overall charge to around 85%.
 
Battery protection mode to extend battery life. Should only be used when device is permanently connected to external charger. When enabled charge current is reduced preventing charging to maximum voltage. This results in lower battery temperature and extended battery lifetime. Please note, this also increases battery charge time and reduces overall charge to around 85%.
 
}}
 
}}
−
|}
 
  
 
{|
 
{|
Line 181: Line 154:
 
|
 
|
 
|==Location Settings==
 
|==Location Settings==
−
[[Image:Location_settings_{{{model|X}}}.png|right|300px]]
+
[[Image:Location_settings_{{{model|X}}}.png|right]]
 
}}
 
}}
 
|}
 
|}
Line 196: Line 169:
  
 
Also, <b>GSM Cell ID</b> and <b>Active GSM Operator</b> should have at least Low priority in I/O settings.<br>[[Image:LBS IO.jpg|left]]
 
Also, <b>GSM Cell ID</b> and <b>Active GSM Operator</b> should have at least Low priority in I/O settings.<br>[[Image:LBS IO.jpg|left]]
−
<br><br><br>
+
<br><br><br><br>
 
}}
 
}}
 
|}
 
|}
−
 
  
 
{|
 
{|
Line 265: Line 237:
  
 
{|
 
{|
−
{{#if:{{{AT_no_show|}}}
+
{{#if:{{{TFT_Static_Navigation|}}}
 
|
 
|
 
|==Static Navigation Settings==
 
|==Static Navigation Settings==
−
[[Image:Static_navigation_PT.png|right]]
+
[[Image:Static_navigation_TFT.png|right]]
 
Static Navigation mode is a filter, which filters out track jumps when the object is stationary. If static navigation filter is disabled, it will apply no changes to GPS data. If static navigation filter is enabled, it will filter changes in GPS position if no movement (as defined by configured movement source) or ignition (as defined by configured ignition source) is detected. It allows filtering GPS jumps when the object is parked (not moving) and GPS position is still traced. <br />
 
Static Navigation mode is a filter, which filters out track jumps when the object is stationary. If static navigation filter is disabled, it will apply no changes to GPS data. If static navigation filter is enabled, it will filter changes in GPS position if no movement (as defined by configured movement source) or ignition (as defined by configured ignition source) is detected. It allows filtering GPS jumps when the object is parked (not moving) and GPS position is still traced. <br />
 
Additionally, user can choose which source (movement or ignition) is used to activate/deactivate static navigation.
 
Additionally, user can choose which source (movement or ignition) is used to activate/deactivate static navigation.
 +
<br>
 +
<br>
 +
}}
 +
|}
 +
{|
 +
 +
{{#if:{{{PT_show|}}}
 +
|
 +
|==Static Navigation Settings==
 +
[[Image:Static_navigation_PT.png|right]]
 +
Static Navigation mode is a filter, which filters out track jumps when the object is stationary. If static navigation filter is disabled, it will apply no changes to GPS data. If static navigation filter is enabled, it will filter changes in GPS position if no movement is detected. It allows filtering GPS jumps when the object is not moving and GPS position is still traced. <br />
 
}}
 
}}
 
|}
 
|}
Line 294: Line 277:
 
  <tr style="vertical-align: top;  text-align: left;">
 
  <tr style="vertical-align: top;  text-align: left;">
 
<td style="width:75%">User can choose sleep mode. More about sleep modes can be found {{{ctrSleepModes|[[{{{model|X}}} Sleep modes|here]]}}}. <br>
 
<td style="width:75%">User can choose sleep mode. More about sleep modes can be found {{{ctrSleepModes|[[{{{model|X}}} Sleep modes|here]]}}}. <br>
−
{{{PT_movement_source|If any of selected movement sources are active, movement mode will be activated. If all selected sources are inactive STOP mode will be enabled. [[Image: PT Sleep exit Source.png]]}}}
+
{{{PT_movement_source|If any of selected movement sources are active, movement mode will be activated. If all selected sources are inactive STOP mode will be enabled.}}}
 
</td>
 
</td>
 
<td>[[Image:Sleep_mode_{{{model|X}}}.png|right]]</td>
 
<td>[[Image:Sleep_mode_{{{model|X}}}.png|right]]</td>
Line 330: Line 313:
  
 
{|
 
{|
−
{{#if:{{{TFT_ignition_source|}}}
+
{{#if:{{{TFT_show|}}}
 
|
 
|
 
|==Ignition Source==
 
|==Ignition Source==
 
[[Image:Mob_Ignition_source.png|right]]
 
[[Image:Mob_Ignition_source.png|right]]
−
User can choose an ignition source from digital input (1, 2 or 3), power voltage, CAN and accelerometer. More than one ignition source can be selected at the same moment. When there are 2 or more sources selected, at least one condition has to be met to change Ignition status. Example: DIN1 and Accelerometer are selected as Ignition source. When the device detects movement, Ignition status will change to 1, regardless that DIN1 value is 0. User can select movement start and movement stop delay time - those parameters are used when accelerometer is selected as an ignition source. Ignition status is used in power management and the following functionalities: Eco/Green driving, Excessive idling, Over speeding, Towing detection and trip.
+
User can choose an ignition source from digital input (1, 2 or 3), power voltage, CAN and accelerometer. More than one ignition source can be selected at the same moment. When there are 2 or more sources selected, at least one condition has to be met to change Ignition status. <br>
 +
''For example'', DIN1 and Accelerometer are selected as Ignition source. When the device detects movement, Ignition status will change to 1, regardless that DIN1 value is 0. <br>
 +
Ignition status is used in power management and the following functionalities: Eco/Green driving, Excessive idling, Over speeding, Towing detection and trip.
 +
<br><br><br>
 
}}
 
}}
 
|}
 
|}
  
 
{|
 
{|
−
{{#if:{{{GH_TMT_section|}}}
+
{{#if:{{{TFT_Accelerometer_Delay|}}}
 
|
 
|
−
|==Movement Settings==
+
|==Accelerometer Delay Settings==
−
[[Image:Accelerometer settings.png|right]]
+
[[Image:Screenshot 2024-03-01 at 14-40-45 5.2. System - Mobility documentation.png|thumb]]
−
Here the user can set the movement start/stop delays. <br/>
+
Here the user can set the movement start/stop delays. <br>
−
''For example'', if the '''''Movement Start Delay''''' is set to 1s and '''''Movement Stop Delay''''' to 60s, the movement will be detected after 1s of moving and defined as stopped after 60s when device stopped moving. Accelerometer Sensitivity in Sleep parameter defines how much movement device needs to experience to exit sleep mode. The lower the sensitivity - the more movement is required.
+
''For example'', if the '''''Movement Start Delay''''' is set to 1s and '''''Movement Stop Delay''''' to 60s, the movement will be detected after 1s of moving and defined as stopped after 60s when device stopped moving.
−
*<code>Minimal</code> – approximately 40% higher movement threshold comparing to Normal
+
<br>
−
*<code>Reduced</code> – approximately 20% higher movement threshold comparing to Normal
+
<table style="border-collapse: collapse; width:50%;" border="1;">
−
*<code>Normal</code> – recommended value for most users
+
    <tr style="text-align: center; background:black; color:white>
−
*<code>Increased</code> – approximately 20% lower movement threshold comparing to Normal
+
        <th width="20%">Parameter ID</th>
−
*<code>Maximum</code> – approximately 40% lower movement threshold comparing to Normal
+
        <th width="30%">Name</th>
−
Changing Accelerometer Sensitivity in Sleep parameter might result in fake movement record or skipped movement events! Only change that if you experience problems with movement detection!
+
        <th width="15%">Min Value</th>
 +
        <th width="15%">Max Value</th>
 +
        <th width="20%">Default Value</th>
 +
    </tr>
 +
    <tr style="text-align: center;">
 +
        <td>19001</td>
 +
        <td>Movement Start Delay</td>
 +
        <td>1</td>
 +
        <td>60</td>
 +
        <td>5</td>
 +
    </tr>
 +
    <tr style="text-align: center;">
 +
        <td>19002</td>
 +
        <td>Movement Stop Delay</td>
 +
        <td>5</td>
 +
        <td>300</td>
 +
        <td>60</td>
 +
    </tr>
 +
</table>
 
}}
 
}}
 
|}
 
|}
Line 362: Line 366:
 
Configurable NTP server (it is possible to configure up to two servers) and what time period to use to re-synchronize time.
 
Configurable NTP server (it is possible to configure up to two servers) and what time period to use to re-synchronize time.
  
−
{| class="wikitable" style="width: 80%;"
+
<table style="border-collapse: collapse; width:60%;" border="1;">
−
! style="width: 15%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |'''Parameter ID'''
+
    <tr style="text-align: center; background:black; color:white>
−
! style="width: 15%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |'''Name'''
+
        <th width="15%">Parameter ID</th>
−
! style="width: 15%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |'''Value/Type'''
+
        <th width="20%">Name</th>
−
! style="width: 15%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |'''Min'''
+
        <th width="15%">Value/Type</th>
−
! style="width: 15%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |'''Max'''
+
        <th width="15%">Min Value</th>
−
! style="width: 15%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |'''Default'''
+
        <th width="15%">Max Value</th>
−
|-
+
        <th width="20%">Default Value</th>
−
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" | 901
+
    </tr>
−
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" | NTP Resync (hours)  
+
    <tr style="text-align: center;">
−
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" | uint8
+
        <td>901</td>
−
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" | 0
+
        <td>NTP Resync (hours)</td>
−
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" | 24
+
        <td>uint8</td>
−
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" | 0
+
        <td>0</td>
−
|-
+
        <td>24</td>
−
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" | 902
+
        <td>3</td>
−
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" | NTP Server 1
+
    </tr>
−
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" | char
+
    <tr style="text-align: center;">
−
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" | 0
+
        <td>902</td>
−
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" | 55
+
        <td>NTP Server 1</td>
−
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" | avl1.teltonika.lt
+
        <td>char</td>
−
|-
+
        <td>0</td>
−
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" | 903
+
        <td>55</td>
−
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" | NTP Server 2
+
        <td>avl1.teltonika.lt</td>
−
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" | char
+
    </tr>
−
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" | 0
+
    <tr style="text-align: center;">
−
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" | 55
+
        <td>903</td>
−
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" | pool.ntp.org
+
        <td>NTP Server 2</td>
−
|}
+
        <td>char</td>
 +
        <td>0</td>
 +
        <td>55</td>
 +
        <td>pool.ntp.org</td>
 +
    </tr>
 +
</table>
  
 
Time synchronization works by waiting a minute on startup to acquire fix and consequently synchronizes the time via GNSS. If the firmware acquires the fix, it starts working in the syncing by GNSS state. This state checks the difference of RTC and GNSS times every second. If the difference of at least 3 seconds persists to be for 5 seconds, the firmware triggers a procedure by GNSS.
 
Time synchronization works by waiting a minute on startup to acquire fix and consequently synchronizes the time via GNSS. If the firmware acquires the fix, it starts working in the syncing by GNSS state. This state checks the difference of RTC and GNSS times every second. If the difference of at least 3 seconds persists to be for 5 seconds, the firmware triggers a procedure by GNSS.
Line 400: Line 409:
 
[[File:Time sync chart.png|thumb]]
 
[[File:Time sync chart.png|thumb]]
  
 +
|}
  
−
 
+
{|
−
 
+
{{#if:{{{GH_TMT_section|}}}
 +
|
 +
|==Movement Settings==
 +
[[Image:Accelerometer settings.png|right]]
 +
Here the user can set the movement start/stop delays. <br/>
 +
''For example'', if the '''''Movement Start Delay''''' is set to 1s and '''''Movement Stop Delay''''' to 60s, the movement will be detected after 1s of moving and defined as stopped after 60s when device stopped moving. Accelerometer Sensitivity in Sleep parameter defines how much movement device needs to experience to exit sleep mode. The lower the sensitivity - the more movement is required.
 +
*<code>Minimal</code> – approximately 40% higher movement threshold comparing to Normal
 +
*<code>Reduced</code> – approximately 20% higher movement threshold comparing to Normal
 +
*<code>Normal</code> – recommended value for most users
 +
*<code>Increased</code> – approximately 20% lower movement threshold comparing to Normal
 +
*<code>Maximum</code> – approximately 40% lower movement threshold comparing to Normal
 +
Changing Accelerometer Sensitivity in Sleep parameter might result in fake movement record or skipped movement events! Only change that if you experience problems with movement detection!
 +
}}
 
|}
 
|}
  
 
{|
 
{|
−
{{#if:{{{TFT_accelerometer_calibration|}}}
+
{{#if:{{{TFT_show|}}}
 
|
 
|
−
|==Accelerometer auto calibration==
+
|==Accelerometer Auto Calibration==
 
[[Image:Accelerometer_auto_calibration.PNG|right]]
 
[[Image:Accelerometer_auto_calibration.PNG|right]]
 
User can disable or enable Accelerometer Auto Calibration and Gravity Filter features. Under Accelerometer Auto Calibration settings, user can choose: <br/>
 
User can disable or enable Accelerometer Auto Calibration and Gravity Filter features. Under Accelerometer Auto Calibration settings, user can choose: <br/>
  
−
*<code>Disable</code> – do not use auto calibration feature (sends AXES raw data),
+
*<code>Disable</code> – do not use Auto Calibration feature (sends AXES raw data),
 
*<code>Once</code> – calibrate one time only,
 
*<code>Once</code> – calibrate one time only,
−
*<code>Continuous</code> – launch auto calibration every trip (note: trip function must be enabled! ). <br />
+
*<code>Continuous</code> – launch Auto Calibration every trip (note: trip function must be enabled! ). <br />
  
−
'''''Important! ''''' If Auto calibration is disabled, device should be mounted according User manual for Eco/Green driving feature to work properly. If enabled, AXES will be reoriented to VEHICLE axes according User manual (+X – Forward, +Y – Left, +Z – Down).  <br />  
+
'''Important!''': If Auto Calibration is disabled, device should be mounted according User manual for Eco/Green driving feature to work properly. If enabled, AXES will be reoriented to VEHICLE axes according User manual (+X – Forward, +Y – Left, +Z – Down).  <br />  
 
Under Gravity Filter settings, user can choose:  
 
Under Gravity Filter settings, user can choose:  
  
Line 422: Line 444:
 
*<code>Enabled</code> – remove GRAVITY component from AXL/Crash.
 
*<code>Enabled</code> – remove GRAVITY component from AXL/Crash.
  
−
(An in-depth explanation for the auto calibration can be found here)
+
(An in-depth explanation for the Auto Calibration can be found here)
  
 
Calibration algorithm is used to recalculate accelerometer axes to represent vehicle’s axes (see Picture below). Vehicles axes are as follows:
 
Calibration algorithm is used to recalculate accelerometer axes to represent vehicle’s axes (see Picture below). Vehicles axes are as follows:
Line 433: Line 455:
 
Once vehicle’s axes are calculated, device is considered calibrated.
 
Once vehicle’s axes are calculated, device is considered calibrated.
 
'''Note''': Moving forward along any axis will generate negative values. This means acceleration will generate -X values, accordingly braking will generate X values. Same goes for other axes.
 
'''Note''': Moving forward along any axis will generate negative values. This means acceleration will generate -X values, accordingly braking will generate X values. Same goes for other axes.
 +
  
 
Commands that can be used during calibration:
 
Commands that can be used during calibration:
−
{| class="wikitable" style="width: 80%;"
 
−
! style="width: 15%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |'''Command'''
 
−
! style="width: 15%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |'''Response'''
 
−
! style="width: 15%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |'''Description'''
 
−
|-
 
−
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" | auto_calibrate:set
 
−
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" | Yes
 
−
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" | Request auto calibration task start
 
−
|-
 
−
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" | auto_calibrate:get
 
−
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" | Yes
 
−
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" | Request calibration info (time, ground vector, side vector)
 
−
|-
 
−
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" | auto_calibrate:clear
 
−
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" | Yes
 
−
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" | Request calibration clear from flash and stop calibration task
 
−
|-
 
−
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" | auto_calibrate:status
 
−
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" | Yes
 
−
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" | Request calibration status and calibration task status
 
−
|}
 
−
Accelerometer Auto Calibration parameter has 3 options:
 
  
−
* Disabled - when this option is selected the device will be calibrated accordingly to its mounted position.
+
<table style="border-collapse: collapse; width:65%;" border="1;">
−
 
+
    <tr style="text-align: center; background:black; color:white>
−
* Once - when this option is selected, the device only tries once to do calibrating. When calibration is done, the device will not try to recalibrate, even if the calibration is not correct. Calibration will be left as it is.
+
        <th width="25%">Command</th>
−
 
+
        <th width="15%">Response</th>
−
* Continuous - calibration process is going on continuously and is always updated, no matter if it is correct or not.
+
        <th width="60%">Description</th>
−
 
+
    </tr>
−
Gravity filter subtracts gravity from the vector when the device is calibrated or when auto calibration is disabled (default values). Parameter functionality is the same in all versions. This also influences the ECO/Green driving scenario algorithm.
+
    <tr style="text-align: center;">
−
 
+
        <td>auto_calibrate:set</td>
−
* Disable - do NOT remove gravity component from AXL/Crash data.
+
        <td>Yes</td>
−
 
+
        <td>Request Auto Calibration task start</td>
−
* Enable - remove gravity component from AXL/Crash. Meaning that in calculations ground vector is subtracted from vehicle projection.
+
    </tr>
−
 
+
    <tr style="text-align: center;">
−
[[Image:Screenshot 2024-03-01 at 14-38-59 5.2. System - Mobility documentation.png|thumb]]
+
        <td>auto_calibrate:get</td>
−
 
+
        <td>Yes</td>
−
'''Important''':If Auto Calibration is disabled, in order for the Eco/Green Driving to work propertly, the device must be mounted according to the TFT100 Mounting Guidelines
+
        <td>Request calibration info (time, ground vector, side vector)</td>
 +
    </tr>
 +
    <tr style="text-align: center;">
 +
        <td>auto_calibrate:clear</td>
 +
        <td>Yes</td>
 +
        <td>Request calibration clear from flash and stop calibration task</td>
 +
    </tr>
 +
    <tr style="text-align: center;">
 +
        <td>auto_calibrate:status</td>
 +
        <td>Yes</td>
 +
        <td>Request calibration status and calibration task status</td>
 +
    </tr>
 +
</table>
  
 
}}
 
}}
 
|}
 
|}
−
=== Mounting Guidelines ===
+
 
 +
{|
 +
{{#if:{{{TFT_show|}}}
 +
|
 +
|=== Mounting Guidelines ===
 +
[[File:Screenshot 2024-03-04 at 09-01-13 tft100-mounting-guidelines.jpg (JPEG Image 900 × 600 pixels).png|thumb]]
 
The device should be mounted according to the picture below. Logo/Antenna must be facing up.
 
The device should be mounted according to the picture below. Logo/Antenna must be facing up.
−
[[File:Screenshot 2024-03-04 at 09-01-13 tft100-mounting-guidelines.jpg (JPEG Image 900 × 600 pixels).png|thumb]]
 
−
<br>
 
−
<br>
 
−
<br>
 
−
<br>
 
 
<br>
 
<br>
 
<br>
 
<br>
Line 494: Line 507:
 
<br>
 
<br>
  
−
===Accelerometer delay===
+
}}
−
Configurable movement start/stop delay settings.
 
−
[[Image:Screenshot 2024-03-01 at 14-40-45 5.2. System - Mobility documentation.png|thumb]]
 
−
 
 
−
{| class="wikitable" style="width: 80%;"
 
−
! style="width: 15%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |'''Parameter ID'''
 
−
! style="width: 15%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |'''Name'''
 
−
! style="width: 15%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |'''Min'''
 
−
! style="width: 15%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |'''Max'''
 
−
! style="width: 15%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" |'''Default'''
 
−
|-
 
−
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" | 19001
 
−
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" | Movement Start delay
 
−
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" | 1
 
−
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" | 60
 
−
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" | 1
 
−
|-
 
−
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" | 19002
 
−
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" | Movement Stop Delay
 
−
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" | 5
 
−
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" | 300
 
−
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" | 60
 
 
|}
 
|}
−
 
−
For example, if the Movement Start Delay is set to 1s and Movement Stop Delay to 60s, the movement will be detected after 1s of moving and defined as stopped after 60s when device stopped moving.
 
  
 
{|
 
{|
Line 525: Line 515:
 
|==Tracking Mode==
 
|==Tracking Mode==
 
[[Image:Tracking_mode.png|right]]
 
[[Image:Tracking_mode.png|right]]
−
<br><b>Power Saving Mode</b> <br>
+
<b>Power Saving Mode</b> <br>
  
 
* <b>Performance</b> - In this mode GNSS module is constantly awake for maximum track quality.<br>
 
* <b>Performance</b> - In this mode GNSS module is constantly awake for maximum track quality.<br>
Line 532: Line 522:
 
The purpose of this feature is to reduce power consumption and its main function is to turn off the GPS module when the device is stationary. For power saving functionality to run several conditions need to be met, one of them: ''Min Period'' value in ''Data Acquisition'' is more than or equal to 60 seconds. In device cold start state the GPS module is turned on for 180 sec. If GPS fix is obtained before this timeout elapses, GPS module turns off and a record is saved, and if not, no record will be saved. Before each new record saving period is expired the device is constantly checking for movement and if no motion has been detected, the GPS module does not turn on and the device waits for a periodic record to be eventually saved. If motion is detected at least 45 seconds before the record saving action, the GPS module will be turned on. If ''Records Saving/Sending Without TS'' configuration is set <span style=color:#F6A83E>Always</span> or <span style=color:#F6A83E>After Time Sync</span> a periodic record is saved and GPS is turned off again. Alternatively, if configuration is set to <span style=color:#F6A83E>After Position Fix</span>, the device will try to obtain GPS fix before record saving takes place and then allow extra ''GPS search period'' to obtain fix. Failing to do so within ''GPS search period'', GPS module will be turned back off and the record will be not saved at all. While this mode is enabled the data acquisition parameters min. distance, min. angle, min. speed delta, are disabled.
 
The purpose of this feature is to reduce power consumption and its main function is to turn off the GPS module when the device is stationary. For power saving functionality to run several conditions need to be met, one of them: ''Min Period'' value in ''Data Acquisition'' is more than or equal to 60 seconds. In device cold start state the GPS module is turned on for 180 sec. If GPS fix is obtained before this timeout elapses, GPS module turns off and a record is saved, and if not, no record will be saved. Before each new record saving period is expired the device is constantly checking for movement and if no motion has been detected, the GPS module does not turn on and the device waits for a periodic record to be eventually saved. If motion is detected at least 45 seconds before the record saving action, the GPS module will be turned on. If ''Records Saving/Sending Without TS'' configuration is set <span style=color:#F6A83E>Always</span> or <span style=color:#F6A83E>After Time Sync</span> a periodic record is saved and GPS is turned off again. Alternatively, if configuration is set to <span style=color:#F6A83E>After Position Fix</span>, the device will try to obtain GPS fix before record saving takes place and then allow extra ''GPS search period'' to obtain fix. Failing to do so within ''GPS search period'', GPS module will be turned back off and the record will be not saved at all. While this mode is enabled the data acquisition parameters min. distance, min. angle, min. speed delta, are disabled.
  
−
Requerements:
+
Requirements:
 
* ''Min Period'' value in ''Data Acquisition'' is more than or equal to 60 seconds;
 
* ''Min Period'' value in ''Data Acquisition'' is more than or equal to 60 seconds;
 
* Tracking mode selected to “Low Power”.
 
* Tracking mode selected to “Low Power”.
Line 572: Line 562:
  
 
{|
 
{|
−
{{#if:{{{TFT_system_settings|}}}
+
{{#if:{{{TFT_show|}}}
 
|
 
|
 
|==Timestamp Backup==
 
|==Timestamp Backup==

Latest revision as of 14:48, 10 July 2024

Pages with broken file links > Template:System settings

System Settings

Movement Source

User can select which source will be used to determine when vehicle is on stop or moving. When multiple are selected, if any of selected are active, Vehicle MOVING mode is used. Available movement source:

Screenshot 2024-03-01 at 14-04-10 5.2. System - Mobility documentation.png
  • Ignition: checks ignition settings which depends on Ignition Source settings;
  • GNSS: movement detected if Fix position available and speed is bigger or equal to 5km/h;
  • Accelerometer: movement detection depends on Accelerometer Delay Settings;
  • CAN Speed: movement is detected if CAN speed retrieved from specific CAN protocol.

When multiple source are selected, if any of selected are active, Movement is detected.

Speed source

If TFT100 is used with CAN modification extra settings option will we available for choosing Speed source.

Available speed source: GNSS or CAN.

If CAN Speed source enabled, it will retrieve speed from CAN data, but if the speed value from CAN data is 0, speed will be retrieved from GNSS data if Position Fix acquired, even though it is not configured.

Screenshot 2024-03-01 at 14-09-53 5.2. System - Mobility documentation.png

Records settings

Here user can enable or disable records when GPS is not available (no GPS fix).

  • After Position Fix - Device must have GPS fix and time to save/send records.
  • After Time Sync - Device must have correct time to save/send records. Allows record sending with no coordinates.
  • Always - Always save/send records. Allows record sending with no coordinates and no correct time.

PDOP filter

User can choose to enable or disable the PDOP filter. This feature allows to discard GNSS module output data if PDOP (Position Dilution of Precision) value is above selected threshold.

  • PDOP filter threshold - PDOP filter threshold value can be entered from which the parameters will be filtered.

Input/Output Mode

User can choose specific external pins to work as an input or as output. Possible valid input/output configurations:

  • Digital input 3 and Digital input 4 (value:5),
  • Digital output 1 and Digital input 4 (value:6),
  • Digital input 3 and Digital output 2 (value:9),
  • Digital output 1 and Digital output 2 (value:10).

LED Indication

User can turn on or off the indication LEDs.

GNSS Source settings

User can configure which GNSS system(s) to use.
User has a choice to use only one system between GPS, GLONASS, Galileo or Beidou and it is possible to choose two or three systems together. One exception is that you cannot combine BeiDou and GLONASS systems together.

Examples of non-configurable GNSS source combinations are:

  • GLONASS + BeiDou;
  • Galileo + GLONASS + BeiDou;
  • GPS + GLONASS + BeiDou;
  • GPS + Galileo + GLONASS + BeiDou.

List of configurable GNSS sources:

  • GPS only;
  • GPS + BeiDou;
  • GPS + GLONASS;
  • GPS + GLONASS + Galileo.

Battery Charge Mode

Here user can change battery charger settings, where charging is allowed. Battery will be charged: On Need (battery will be charged anytime when it needs to be charged) and After Ignition ON (battery will be charged only when ignition is on).

Three charging modes is available:

  • On neeed: charger enabled if external voltage is higher than 5.05 voltage and Battery Voltage is below 3.90V. Charging is disabled if device enters any sleep mode.
  • After Ignition On: charger enabled after ignition is turned on, except if the battery is fully charged or 10-minute timeout has not passed since the device was turned on for faster FIX receiving.
  • Always: charger is always enabled, except if the battery is fully charged or 10-minute timeout has not passed since the device was turned on for faster FIX receiving.

Screenshot 2024-03-01 at 14-11-41 5.2. System - Mobility documentation.png

Analog Input Value Range

User can choose analog input range of 15 V or 150 V.

Input range used to determine lowest voltage for DIN1 and DIN2 activation.

Screenshot 2024-03-01 at 14-13-04 5.2. System - Mobility documentation.png

Lowest voltage to enabled DIN for 15V range - 2.5V

Lowest voltage to enabled DIN for 150V range - 9V

DOUT Overcurrent protection

DOUTs have overcurrent protection that triggers after the current exceeds 300 mA. This protection works by generating pulses on the hardware. When the firmware detects at least 20 impulses on a DOUT it turns off that DOUT for 5 minutes. During this time all scenarios that try to turn this DOUT on will fail.

Data Protocol

User can choose which protocol version to use for data sending to server.

  • Codec 8 supports up to 255 AVL ID;
  • Codec 8 Extended supports up and above 255 AVL ID.

Power On By USB/Charger

PT Power on by usb.png

Note: This feature is available forwards from FW version 55.02.03.Rev.05
Device supports two working modes: normal mode, where the device works as usual, and charging mode, which is entered when Power On By USB/Charger parameter is disabled. To enter normal mode, device can be turned on by power button or by USB charger, if Power On By USB/Charger parameter is set to Enable.

Continuous Charging Mode

PT continuous charging.png

Note: This feature is available forwards from FW version 55.02.03.Rev.05
Battery protection mode to extend battery life. Should only be used when device is permanently connected to external charger. When enabled charge current is reduced preventing charging to maximum voltage. This results in lower battery temperature and extended battery lifetime. Please note, this also increases battery charge time and reduces overall charge to around 85%.

Location Settings

File:Location settings X.png

Location Source

LBS - location based services. It helps us to find the approximate location without using a GNSS, but using cell towers information instead. Device cannot find the location using LBS by itself, approximate location is calculated on the server side according to the information provided by the device. Therefore, to locate a unit by LBS the device should send at least 4 parameters: mcc, mnc, lac, cell ID.

  • If LBS is selected as a location source, the device will send information about the cell towers to the server and will not use GNSS.
  • If GNSS or LBS is selected, device will use GNSS if the satellites are visible, if not - it will start sending cell towers information to the server, which will be able to calculate the approximate location using LBS.
Also, GSM Cell ID and Active GSM Operator should have at least Low priority in I/O settings.
LBS IO.jpg





GNSS Source settings

User can configure which GNSS system(s) to use.
User has a choice to use only one system between GPS, GLONASS, Galileo or Beidou and it is possible to choose two or three systems together. One exception is that you cannot combine BeiDou and GLONASS systems together.

Examples of non-configurable GNSS source combinations are:

  • GLONASS + BeiDou;
  • Galileo + GLONASS + BeiDou;
  • GPS + GLONASS + BeiDou;
  • GPS + Galileo + GLONASS + BeiDou.

List of configurable GNSS sources:

  • GPS only;
  • GPS + BeiDou;
  • GPS + GLONASS;
  • GPS + GLONASS + Galileo.

GNSS control

User can manually turn ON/OFF the GNSS module. For example, if button 'Turn off GNSS' is pressed and device is trying to acquire GNSS fix for a record, it will turn GNSS back on. If GNSS module is turned ON using 'Turn on GNSS' button, it will be active for undefined period of time until USB is disconnected and device is going to sleep, record sending is finished or the 'Turn off GNSS' button is pressed again.

Coordinate acquisition timeout

The configured time adds a delay when the coordinates of the device are taken to stabilize and ensure accuracy. Important thing to note that TAT100 can take up to 180 seconds to get the GPS fix and the configured timeout would only go after the GPS fix timeout has finished or the coordinates were received.

Static Navigation Settings

Static navigation helps to save power by not enabling the GPS module and instantly generating a record if movement was not detected.

When enabled the device monitors the accelerometer and registers movement events by configured movement sensitivity. When the device wakes up to save and send a periodic record, and movement was not registered, the device will use the last known coordinates and will generate a record without turning ON the GPS module. However, if there are no last known coordinates, then the device will enable the GPS module and will try to get a new GPS fix.

The functionality is illustrated in the flowchart below:

Staticnavflowchart.png

Movement sensitivity

This feature sets the sensitivity threshold levels for movement event registration. Higher configured level makes the device “less sensitive” and vice versa. Currently, there are 10 configurable Movement Sensitivity levels. Levels are measured in mG - thousandth parts of the gravitational force equivalent or gravitational acceleration of Earth (9.8 m/s). It means that if Movement Sensitivity is set to 1000 mG, the device has to be free falling, experience fierce stops/accelerations or vibrations to detect movement.

Static Navigation Settings

Static navigation TFT.png

Static Navigation mode is a filter, which filters out track jumps when the object is stationary. If static navigation filter is disabled, it will apply no changes to GPS data. If static navigation filter is enabled, it will filter changes in GPS position if no movement (as defined by configured movement source) or ignition (as defined by configured ignition source) is detected. It allows filtering GPS jumps when the object is parked (not moving) and GPS position is still traced.
Additionally, user can choose which source (movement or ignition) is used to activate/deactivate static navigation.

Static Navigation Settings

Static navigation PT.png

Static Navigation mode is a filter, which filters out track jumps when the object is stationary. If static navigation filter is disabled, it will apply no changes to GPS data. If static navigation filter is enabled, it will filter changes in GPS position if no movement is detected. It allows filtering GPS jumps when the object is not moving and GPS position is still traced.

Call Duration Limits

Call duration limits.png

These is two places for these settings. First one can be found in the SMS \ Calls Settings section. This setting applies to incoming and outgoing calls, except for the keyboard “Call” action and the Amber Alert feature.

Cal duration limit2.png

Second one can be found in the Keyboard section. These settings are only visible when the button action is Call. There is only one parameter per button, so the same parameter applies to all button presses.

Sleep Mode

User can choose sleep mode. More about sleep modes can be found here.

If any of selected movement sources are active, movement mode will be activated. If all selected sources are inactive STOP mode will be enabled.

File:Sleep mode X.png

Ignition Source

Mob Ignition source.png

User can choose an ignition source from digital input (1, 2 or 3), power voltage, CAN and accelerometer. More than one ignition source can be selected at the same moment. When there are 2 or more sources selected, at least one condition has to be met to change Ignition status.
For example, DIN1 and Accelerometer are selected as Ignition source. When the device detects movement, Ignition status will change to 1, regardless that DIN1 value is 0.
Ignition status is used in power management and the following functionalities: Eco/Green driving, Excessive idling, Over speeding, Towing detection and trip.


Accelerometer Delay Settings

Screenshot 2024-03-01 at 14-40-45 5.2. System - Mobility documentation.png

Here the user can set the movement start/stop delays.
For example, if the Movement Start Delay is set to 1s and Movement Stop Delay to 60s, the movement will be detected after 1s of moving and defined as stopped after 60s when device stopped moving.

Parameter ID Name Min Value Max Value Default Value
19001 Movement Start Delay 1 60 5
19002 Movement Stop Delay 5 300 60

Time Synchronization

Time synchronization.PNG

User can select which NTP server (it is possible to configure up to two servers) and what time period to use to re-synchronize time.

Configurable NTP server (it is possible to configure up to two servers) and what time period to use to re-synchronize time.

Parameter ID Name Value/Type Min Value Max Value Default Value
901 NTP Resync (hours) uint8 0 24 3
902 NTP Server 1 char 0 55 avl1.teltonika.lt
903 NTP Server 2 char 0 55 pool.ntp.org

Time synchronization works by waiting a minute on startup to acquire fix and consequently synchronizes the time via GNSS. If the firmware acquires the fix, it starts working in the syncing by GNSS state. This state checks the difference of RTC and GNSS times every second. If the difference of at least 3 seconds persists to be for 5 seconds, the firmware triggers a procedure by GNSS.

After that, the the time difference is still calculated, but the difference is expected to persist for at least 5 minutes to trigger a GNSS time resynchronization. This is done to prevent false GNSS timestamps (such as year 2080 and etc.). If there’s no time difference found, the difference is expected to persist again for a period of 5 seconds later on when calculating. In the case that there is no fix or it is lost during the syncing by GNSS state, the firmware goes to state of syncing by NTP.

Entering the state of NTP syncing, the firmware immediately attempts to synchronize the time by triggering NTP and later on, does this periodically every time the configured NTP resynchronization time is reached. If the NTP resynchronization time is set to 0, no periodical resynchronization is done in this state. Time synchronization by NITZ can occur any time.

Time sync chart.png

Movement Settings

Accelerometer settings.png

Here the user can set the movement start/stop delays.
For example, if the Movement Start Delay is set to 1s and Movement Stop Delay to 60s, the movement will be detected after 1s of moving and defined as stopped after 60s when device stopped moving. Accelerometer Sensitivity in Sleep parameter defines how much movement device needs to experience to exit sleep mode. The lower the sensitivity - the more movement is required.

  • Minimal – approximately 40% higher movement threshold comparing to Normal
  • Reduced – approximately 20% higher movement threshold comparing to Normal
  • Normal – recommended value for most users
  • Increased – approximately 20% lower movement threshold comparing to Normal
  • Maximum – approximately 40% lower movement threshold comparing to Normal

Changing Accelerometer Sensitivity in Sleep parameter might result in fake movement record or skipped movement events! Only change that if you experience problems with movement detection!

Accelerometer Auto Calibration

Accelerometer auto calibration.PNG

User can disable or enable Accelerometer Auto Calibration and Gravity Filter features. Under Accelerometer Auto Calibration settings, user can choose:

  • Disable – do not use Auto Calibration feature (sends AXES raw data),
  • Once – calibrate one time only,
  • Continuous – launch Auto Calibration every trip (note: trip function must be enabled! ).

Important!: If Auto Calibration is disabled, device should be mounted according User manual for Eco/Green driving feature to work properly. If enabled, AXES will be reoriented to VEHICLE axes according User manual (+X – Forward, +Y – Left, +Z – Down).
Under Gravity Filter settings, user can choose:

  • Disabled – do not remove GRAVITY component from AXL/Crash data,
  • Enabled – remove GRAVITY component from AXL/Crash.

(An in-depth explanation for the Auto Calibration can be found here)

Calibration algorithm is used to recalculate accelerometer axes to represent vehicle’s axes (see Picture below). Vehicles axes are as follows:

  • X is front.
  • Y is left.
  • Z is down.
Screenshot 2024-03-01 at 14-34-37 vehicleaxes.png (PNG Image 1186 × 596 pixels).png

Once vehicle’s axes are calculated, device is considered calibrated. Note: Moving forward along any axis will generate negative values. This means acceleration will generate -X values, accordingly braking will generate X values. Same goes for other axes.


Commands that can be used during calibration:

Command Response Description
auto_calibrate:set Yes Request Auto Calibration task start
auto_calibrate:get Yes Request calibration info (time, ground vector, side vector)
auto_calibrate:clear Yes Request calibration clear from flash and stop calibration task
auto_calibrate:status Yes Request calibration status and calibration task status

Mounting Guidelines

Screenshot 2024-03-04 at 09-01-13 tft100-mounting-guidelines.jpg (JPEG Image 900 × 600 pixels).png

The device should be mounted according to the picture below. Logo/Antenna must be facing up.









Tracking Mode

Tracking mode.png

Power Saving Mode

  • Performance - In this mode GNSS module is constantly awake for maximum track quality.
  • Low power - Battery saving mode, where GNSS is woken up only when it is time to acquire Position. Standard Sleep modes are not available in this mode.

The purpose of this feature is to reduce power consumption and its main function is to turn off the GPS module when the device is stationary. For power saving functionality to run several conditions need to be met, one of them: Min Period value in Data Acquisition is more than or equal to 60 seconds. In device cold start state the GPS module is turned on for 180 sec. If GPS fix is obtained before this timeout elapses, GPS module turns off and a record is saved, and if not, no record will be saved. Before each new record saving period is expired the device is constantly checking for movement and if no motion has been detected, the GPS module does not turn on and the device waits for a periodic record to be eventually saved. If motion is detected at least 45 seconds before the record saving action, the GPS module will be turned on. If Records Saving/Sending Without TS configuration is set Always or After Time Sync a periodic record is saved and GPS is turned off again. Alternatively, if configuration is set to After Position Fix, the device will try to obtain GPS fix before record saving takes place and then allow extra GPS search period to obtain fix. Failing to do so within GPS search period, GPS module will be turned back off and the record will be not saved at all. While this mode is enabled the data acquisition parameters min. distance, min. angle, min. speed delta, are disabled.

Requirements:

  • Min Period value in Data Acquisition is more than or equal to 60 seconds;
  • Tracking mode selected to “Low Power”.


GNSS module will be turned OFF:

  • Fix was not caught in 45 seconds;
  • Fix was stable for 30 seconds.


Power Saving Mode Values:

Parameter ID Name Min Value Max Value
909 Power Saving Mode 0 - Performance 1 - Low Power
905 GPS accuracy 0.1 20
906 GPS Satellites Quantity 4 20

Timestamp Backup

Timestamp Backup.png

Enables or disables the Timestamp Backup synchronization.

This feature, if enabled, every minute saves current timestamp to non-volatile memory (persist after power cutoff). If device was restarted for some reason and was unable to synchronize time, device will use the last saved timestamp as current time.


GNSS Fix Holdout

Gnssfixholdout.jpg

If this parameter is ‘Enable’, then for the first 30s of GNSS fix, coordinates are not considered valid. ‘Disable’ means that from the start of the fix coordinates are considered valid.

Retrieved from "https://wiki.teltonika-gps.com/index.php?title=Template:System_settings&oldid=99513"