Difference between revisions of "Template:FMB1 First start card withoutSD"

From Wiki Knowledge Base | Teltonika GPS
 
Line 12: Line 12:
 
=='''How to insert {{{sim_type|Micro-}}}SIM card'''==
 
=='''How to insert {{{sim_type|Micro-}}}SIM card'''==
  
#Gently remove {{{model|FMB1YX}}} '''cover''' using '''plastic pry tool''' from both sides.
+
#Gently remove {{{model|FMX2YX}}} '''cover''' using '''plastic pry tool''' from both sides.
 +
#Disassemble the device, remove both sides from the PCB
 
#Insert '''{{{sim_type|Micro-}}}SIM''' card as shown with '''PIN request disabled''' or read {{{sim_pin|[[FMB120 Security info|'''Security info''']]}}} how to enter it later in Configurator. Make sure that {{{sim_type|Micro-}}}SIM card '''cut-off corner''' is pointing forward to slot. {{{dual_sim|'''SIM slot 1''' is closer to PCB, '''SIM slot 2''' is the upper one.}}}
 
#Insert '''{{{sim_type|Micro-}}}SIM''' card as shown with '''PIN request disabled''' or read {{{sim_pin|[[FMB120 Security info|'''Security info''']]}}} how to enter it later in Configurator. Make sure that {{{sim_type|Micro-}}}SIM card '''cut-off corner''' is pointing forward to slot. {{{dual_sim|'''SIM slot 1''' is closer to PCB, '''SIM slot 2''' is the upper one.}}}
 +
#Connect the battery
 +
#Place the battery in the housing
 
#Attach device '''cover''' back.
 
#Attach device '''cover''' back.
#Device is ready to be connected.
 
  
[[Image:FMB1_cover1_correct.png|280px]][[Image:FMB1_cover2_correct.png|280px]][[Image:FMB1_cover3_correct.png|280px]][[Image:FMB1_cover4_correct.png|280px]]
+
 
 +
[[Image:FMX2YX_cover_open1_correct.png|280px]][[Image:FMX2YX_cover2_correct.png|280px]][[Image:FMX2YX_cover3_correct.png|280px]][[Image:FMX2YX_cover4_correct.png|280px]][[Image:FMX2YX_cover5_correct.png|middle|280px]][[Image:FMX2YX_cover6_correct.png|middle|280px]]
  
 
{|
 
{|

Latest revision as of 09:56, 19 January 2022

Qsg rut950 teltonika.PNG


GNSS/GSM/Blue-tooth tracker with internal GNSS/GSM antennas

Fmb120 man.png



How to insert Micro-SIM card

  1. Gently remove FMX2YX cover using plastic pry tool from both sides.
  2. Disassemble the device, remove both sides from the PCB
  3. Insert Micro-SIM card as shown with PIN request disabled or read Security info how to enter it later in Configurator. Make sure that Micro-SIM card cut-off corner is pointing forward to slot. SIM slot 1 is closer to PCB, SIM slot 2 is the upper one.
  4. Connect the battery
  5. Place the battery in the housing
  6. Attach device cover back.


FMX2YX cover open1 correct.pngFMX2YX cover2 correct.pngFMX2YX cover3 correct.pngFMX2YX cover4 correct.pngFMX2YX cover5 correct.pngFMX2YX cover6 correct.png

Alert.png
Micro-SIM card insertion/removal must be performed when device is powered off – external voltage and internal battery disconnected. Otherwise Micro-SIM card might be damaged or device will not detect it.