EYE SENSOR / BTSMP1

Introduction

Wireless solutions open up new horizons for your business and help to keep an eye on your assets. Discover our brand-new and certified Bluetooth Low Energy ID sensor model from Teltonika with robust waterproof casing and a long-lifetime battery. The model is designed for a low-cost fast and easy configuration and integration to save precious time, resources, and ensure accountability.

About BTSMP1

Perfect for traceability use cases, delivery tracking, monitoring of various movable objects in logistics (trailers, containers), agriculture (tractor attachments), and constructions (tools and inventory). Sensors data makes it especially suitable for cold chain refrigerator use cases. The built-in accelerometer can detect item movement or fall events. Magnet detection can be used for wireless open/close detection and notifications such as trailer door events, etc. EYE sensor supports iBeacon and Eddystone protocols. The device is fully compatible with the Teltonika firmware platform which provides extended functionality. Configure, scan, and update anytime anywhere with a dedicated Teltonika mobile app

Product Specification

Features

Functionalities
Beacon ID, LED, Temperature, Humidity, Accelerometer, Magnet detection

Dimensions and weight
Dimensions	56,6 mm x 38 mm x 13 mm
Weight 19 g	18g

Battery and power (not confirmed)
Model	CR2450
Type	Type Lithium, Manganese Dioxide
Total Capacity	620 mAh
Replaceable	No
Battery life (Tx=2 dBm; interval: 3 s)	2.5+ years (Tx=2 dBm; interval: 3 s)
Battery life (Tx=2 dBm; interval: 10 s)	5+ years (Tx=2 dBm; interval: 10s)

Electronic
Microcontroller	ST Microelectronics BlueNRG-2

Connectivity
Bluetooth	Bluetooth 4.2 compliant, Bluetooth 5.2 certified
Range	80 m
Available transmission power levels	Up to 8 dBm
Sensitivity	-88 dBm

Casing
Protection	IP67
Mounting	Two holes to screw/leash/strip, tape
Customization	Custom logo upon request (Special conditions)

Environmental Requirements
Humidity (non-condensing)	From 0% to 95%
Operational temperature	-20°C / +60°C (-4°F / +140°F)

Protocols compatibility
iBeacon	Yes *iOS doesn't show devices with iBeacon protocol
Eddystone	Yes
EYE Sensor	Yes

Certificates
CE (EU)	Yes
FCC (USA)	Yes
UKCA (UK)	Yes
RoHS	Yes
E-mark	Yes

Dimensions

Mounting recomendations

EYE Accessory Configuration

Devices work constantly and are ready to perform out of the box. Default basic Sensor settings are set to:
• Transmitting at 2 dBm power.
• Data advertising at 3 second intervals.
• Eddystone protocol

If you would like to change these settings you will need to:
1) Download and install EYE APP - Teltonika application to change sensor settings.

Eye app

With the application you will be able to scan for visible Teltonika EYE devices, check their statuses or connect for configuration or firmware update.

Devices in view

In this window you will see all visible devices. You have options to see devices in Short list or in default list. When looking at devices in default list you will be able to open Detailed view of devices and check transmitted data statuses. Additionaly if you are looking for specific devices you will be able to use Search function to filter search options. When in this window select a device of your choice to connect and after passing pin code you will go to device overview window.

Overview window

In overview window you can see device details, check firmware version and update if available , go to device configuration settings. If you select to Configure device new window will open with Basic and Advanced settings.

Configure window

In this window you can check and change device configuration settings. In main tab Basic Settings you can change main settings. Change Device name, Power signal strength, Advertising interval and Packet transmission type*. For more settings go to Advanced settings tab to enable various events.

Advanced configuration window

Advanced configuration: Beacon Settings

In Advanced settings tab you can can configure EYE beacon sensor parameters: Beacon information (iBeacon ID*, Eddystone ID). UUID/MINOR/MAJOR parameter can be changed for iBeacon ID*. Namespace ID/Instance ID can be changed for Eddystone ID. If you scroll down you will be able to adjust Sensor reading interval and event settings of the EYE Sensor Note: iOS doesn't show devices with iBeacon protocol

Advanced configuration: Sensor reading and events

Magnetic field event - adjust if the device generates events based on detection or exit (loss) of the magnet.	Humidity event - adjust if the device generates events based on entrance or exit to selected humidity range	Temperature event - adjust if the device generates events based on entrance or exit to selected temperature range	Movement event - adjust movement/stop detection and timeouts it takes to register movement / stopping
Maximum event duration - how long will one event be advertised	Event advertising settings - how often device will scan for new events	Sensor reading interval - how often values are updated by the device

FM Tracker Configuration

Teltonika configurator (standard functionality / advanced mode)

If you have firmware / configurator which does not support EYE sensor tab in Bluetooth 4.0 section, then you can still use Avanced BLE configuration to connect with EYE Sensors.

To configure FM with BTSMP1 EYE Sensor:

1. In System settings Enable Codec8 Extended;
2. In GPRS settings Configure GPRS Settings and Server Settings
3. In Bluetooth settings Enable Bluetooth, set this setting as either "Enable (hidden)" or "Enable (visible)", otherwise Bluetooth will be disabled;
4. In Bluetooth 4.0 settings:
   1. set Non Stop Scan to "Disable", configure "Update Frequency" and "Scan duration" as 30 seconds. These settings will bring the best results for BLE scanning with our device;
   2. In Bluetooth 4.0 settings Advanced Mode Settings Load EYE Sensor preset according to the set Eye Sensor protocol set in EYE App Basic Configuration window
   3. Configure MAC address of the sensor
5. Make sure that name of the sensor is default length (10 symbols) in EYE App Basic Configuration window

If you do not have preset you can download them from below table:

Advanced mode configuration:

EYE Sensor Packet Setting:
Preset you should use:	EYE Sensors	EYE iBeacon	EYE Eddystone
Preset download link:
Configuration example download link:
Instructions how you can manually add a preset: link

Preset Configuration:

If EYE Sensor Packet Settings is EYE Sensors or Eddystone and EYE Sensors:

If EYE Sensor Packet Settings is EYE Sensors or iBeacon and EYE Sensors:

IO element value descriptions:

NAME	DESCRIPTION
Custom1	Flags
Temperature	Ambient temperature in Celsius
Humidity	Ambient humidity in percent
Custom2	Movement and movement events count
Custom3	Angle
Custom4	Battery voltage (2000 + (VALUE * 10)) in mV

Note: To receive data need to enable corresponding IO elements in I/O tab.

Teltonika configurator new functionalities (not released yet)

Starting with firmware 03.27.07.Rev.323 there is additional tabs available in Bluetooth 4.0 section that allow for easier configuration to connect FM and EYE sensor or beacon.

Bluetooth 4.0
Functionalities were reorganized and transferred to Bluetooth 4.0 configuration tab with additional horizontal tabs selection for specific settings:

• Global - Parameters responsible for device scanning ability like power and duratations.
• EYE - Parameters to configure data reading from EYE sensors.

Common settings

• Non Stop Scan - Enable Non Stop Scan feature, the device will try to scan for the sensors all the time if any of them are configured.
• Sensors and Beacons Update frequency - changes sensors temperature/humidity/battery voltage data update frequency. Minimum value: 30s, maximum value: 65535s. Recommended value 30.
• BLE Scan Duration - Sensors data reading time. Recommended value 30.
• Scan retries until error - Scan retries count, till start to show the value as Error '3000' - sensor disconnected. Recommended value 30.
• BT Power Level - Telematics device Bluetooth power level setting.
• BLE Broadcasting service ID - Telematics device can broadcast configured ID.
• BLE connection control - Connection mode settings. If broadcasting ID is configured, parameter should be set to Prohibit.

EYE Sensor

EYE Sensor functionality allows to configure MAC addresses for 4 sensors that user wants to read
Data clear period - if value equal or higher than 1, it will clear sensors BLE IO elements values if they were not updated for configurated amount of time.


I/O elements
Starting with firmware 03.27.07.Rev.323 there is additional tabs available in Bluetooth 4.0 section that allow for easier configuration to connect FM and EYE sensor or beacon.
Note: If you are using presets(firmware/configurator without EYE product support), then refer to BLE Sensors I/O elements table instead.

Table below describes I/O elements which were added for EYE sensor and proximity functionalities.

Property ID in AVL packet	Property name	Bytes	Type	Min	Max	Multiplier	Units	Description
10800	EYE Temperature 1	2	Signed	-32768	32768	0,01	°C	Temperature measured by EYE sensor 1
10801	EYE Temperature 2	2	Signed	-32768	32768	0,01	°C	Temperature measured by EYE sensor 2
10802	EYE Temperature 3	2	Signed	-32768	32768	0,01	°C	Temperature measured by EYE sensor 3
10803	EYE Temperature 4	2	Signed	-32768	32768	0,01	°C	Temperature measured by EYE sensor 4
10804	EYE Humidity 1	1	Unsigned	0	100	-	%	Humidity measured by EYE sensor 1
10805	EYE Humidity 2	1	Unsigned	0	100	-	%	Humidity measured by EYE sensor 2
10806	EYE Humidity 3	1	Unsigned	0	100	-	%	Humidity measured by EYE sensor 3
10807	EYE Humidity 4	1	Unsigned	0	100	-	%	Humidity measured by EYE sensor 4
10808	EYE Magnet 1	1	Unsigned	0	1	-	-	Magnet measured by EYE sensor 1
10809	EYE Magnet 2	1	Unsigned	0	1	-	-	Magnet measured by EYE sensor 2
10810	EYE Magnet 3	1	Unsigned	0	1	-	-	Magnet measured by EYE sensor 3
10811	EYE Magnet 4	1	Unsigned	0	1	-	-	Magnet measured by EYE sensor 4
10812	EYE Movement 1	2	Unsigned	0	0xFFFF	-	-	Movement state and count measured by EYE sensor 1
10813	EYE Movement 2	2	Unsigned	0	0xFFFF	-	-	Movement state and count measured by EYE sensor 2
10814	EYE Movement 3	2	Unsigned	0	0xFFFF	-	-	Movement state and count measured by EYE sensor 3
10815	EYE Movement 4	2	Unsigned	0	0xFFFF	-	-	Movement state and count measured by EYE sensor 4
10816	EYE Angle 1	4	Unsigned	0	0xFFFFFFFF	-	-	Pitch and Roll angles measured by EYE sensor 1
10817	EYE Angle 2	4	Unsigned	0	0xFFFFFFFF	-	-	Pitch and Roll angles measured by EYE sensor 2
10818	EYE Angle 3	4	Unsigned	0	0xFFFFFFFF	-	-	Pitch and Roll angles measured by EYE sensor 3
10819	EYE Angle 4	4	Unsigned	0	0xFFFFFFFF	-	-	Pitch and Roll angles measured by EYE sensor 4
10820	EYE Low Battery 1	1	Unsigned	0	1	-	-	Low Battery indication EYE sensor 1
10821	EYE Low Battery 2	1	Unsigned	0	1	-	-	Low Battery indication EYE sensor 2
10822	EYE Low Battery 3	1	Unsigned	0	1	-	-	Low Battery indication EYE sensor 3
10823	EYE Low Battery 4	1	Unsigned	0	1	-	-	Low Battery indication EYE sensor 4
10824	EYE Battery Voltage 1	1	Unsigned	0	0xFF	-	-	Battery Voltage of EYE sensor 1
10825	EYE Battery Voltage 2	1	Unsigned	0	0xFF	-	-	Battery Voltage of EYE sensor 2
10826	EYE Battery Voltage 3	1	Unsigned	0	0xFF	-	-	Battery Voltage of EYE sensor 3
10827	EYE Battery Voltage 4	1	Unsigned	0	0xFF	-	-	Battery Voltage of EYE sensor 4
10828	EYE Proximity Near	1024	HEX	0	1024	-	-	Beacon list in Near Proximity zone
10829	EYE Proximity Away	1024	HEX	0	1024	-	-	Beacon list in Away Proximity zone
10830	EYE Proximity Far Away	1024	HEX	0	1024	-	-	Beacon list in Away Far zone
10831	EYE Proximity Lost	1024	HEX	0	1024	-	-	List of Beacon which were lost from proximity zones

EYE Sensor Protocol overview

Sensor advertising

Beacon and sensors data

Protocol description

At the highest-level Bluetooth LE advertising packet consists of Advertising Indication and Scan Response. Both packets can be maximum of 31 bytes in size. Advertising Indication packet is always broadcasted when Scan Response is broadcasted only if Observer device requests it by using Active Scan.

BTSMP1 uses Advertising Indication to send beacon data which can be configured to select between iBeacon and Eddystone protocols or to be disabled at all. In that case, data which is shown as Scan Response in protocol overview will be sent as Advertising Indication without Scan Response following it.

Scan Response is used to send device name and manufacturer specific data. Manufacturer specific data includes Teltonika Company ID (0x089A) and protocol version (0x01). It is followed by Flag Encoded Data (Table 1) and Extended Data (Table 2). Later on, protocol will be highly configurable in and will allow to disable/enable sending of device name or any sensor value allowing to reduce size of the packet being sent.

Device Name has the following default value for Beacon – ID1_XXXXXXX

Table 1. Flag Encoded Date

Data	Size (Bytes)	Description
Flags	1	Each set bit (0-7) means the presence of value (0-7). Bits: 0 – Temperature value presence 1 – Humidity value presence 2 – Magnetic sensor presence 3 – Magnetic sensor state (1 magnetic field is detected/0 magnetic field is not detected) Valid value is present only if bit 2 flag is set. 4 – Movement sensor counter 5 – Movement sensor angle 6 – Low Battery indication (if set to 1 low battery voltage detected) 7 – Battery voltage value presence
Value 0	2	Temperature Value in Celsius * 100 NOTE: present only if bit 0 is set, otherwise is not being sent
Value 1	1	Humidity Value in percent NOTE: present only if bit 1 is set, otherwise is not being sent
Value 2	2	Movement Sensor counter Most significant bit indicates movement state and 15 least significant bits represent count of movement events. NOTE: present only if bit 4 is set, otherwise is not being sent
Value 3	3	Movement sensor angle Most significant byte – pitch (-90/+90) Two least significant bytes – roll (-180/+180) NOTE: present only if bit 5 is set, otherwise is not being sent
Value 4	1	Battery Voltage Battery voltage in mV = 2000 + VALUE * 10 NOTE: present only if bit 7 is set, otherwise is not being sent

Table 2. Extended Data

Type	Description
1 byte types
0	For future use
...	For future use
49	For future use
2 bytes types
50	For future use
...	For future use
99	For future use
4 bytes types
100	For future use
...	For future use
149	For future use
8 bytes types
150	For future use
...	For future use
199	For future use
Variable size types
200	For future use
...	For future use
255	For future use

EYE Sensor protocol parsing example

Unparsed data
0201061AFF4C000215FFFFFFFF0B8C404510C655AAB636EBEFBB700055020C094D50315F313233343536370EFF9A0801B708B4120000C1001A6E

Parsed data
Parameter		HEX Code Part	Actual Value
	Length	02
	Type	01
	Flags	06
	Length	1A
	Type	FF
	Apple company identifier (big endian)	4C00
	Beacon type	0215
	UUID	FFFFFFFF0B8C404510C655AAB636EBEF
	Major	BB70
	Minor	0055
	Power	02
	Length	0C
	Type	09
	Device name	4D50315F31323334353637
	Length	0E
	Type	FF
	Teltonika company ID (big endian)	9A08
	Protocol version	01
	Flags	B7	Raw value example 0xB7. Data has to be interpretated as binary value. In this example would be (MSB)11011 0111(LSB) and is parsed from least significant byte(LSB). 0 – Temperature value presence. 1 Means device is reading and transmitting temperature value. 1 – Humidity value presence. 1 Means device is reading and transmitting humidity value. 2 – Magnetic sensor presence. 1 Means device is reading and transmitting Magnetic sensor value. 3 – Magnetic sensor state (1 magnetic field is detected/0 magnetic field is not detected) Valid value is present only if bit 2 flag is set. 4 – Movement sensor counter. 1 Means device is reading and transmitting movement state and count values. 5 – Movement sensor angle. 1 Means device is reading and transmitting angle roll and pitch values. 6 – Low Battery indication. 0 – Means device battery is from 100 to 15 % (When value changes to 1 Battery level is lower than 15 %. 7 – Battery voltage value presence. 1 Means device is reading and transmitting battery voltage value.
	Temperature	08B4	Raw value example 0x08B4 hex, 2228 dec. Raw value needs to be divided by 100. Real temperature is 22,28 Celsius.
	Humidity	12	Raw value example 0x12 hex, 18 dec. Decimal value is humidity in percent. Humidity 18 %
	Movement	0CCB	(MSB)0000 1100 1100 1011(LSB) binary 0 - Most significant byte(MSB) represents Movement status. In this case device is not moving 0. If it was 1 device is moving. 000 1100 1100 1011 – represent detected movements count 3275 decimal value means device has detected total 3275 movement events,
	Angle	0BFFC7	C1 – Most significant byte represents device pitch. Device pitch can be from -90 to 90 degrees. In this example device pitch is 0000 1011 (2's complement) = 11° degrees. FFC7– Two least significant bytes represent device roll. Device roll can be from -180 to 180 degrees. In this example device Roll is 1111 1111 1100 0111 (2's complement) = -57° degrees
	Battery voltage	6E	Battery voltage – raw value example 0x67 hex. Decimal value of parameter 103. To calculate battery voltage need to use calculation 2000 + (VALUE * 10). In this case battery voltage value 2000+(103x10)= 3030 mV

FM Packet parsing example (standard functionality / advanced mode)

Received data in hexadecimal stream: 00000000000000488E010000017CA6B6BFD8010F0E5188209AB482008600A80F0000000 00006000000020019090400560024000301CF0000001601D00000FF4D01D10000006D00000001014B0001B6010000CF7D

AVL Data Packet
AVL Data Packet Part		HEX Code Part
	Zero Bytes	00 00 00 00
	Data Field Length	00 00 00 48
	Codec ID	8E (Codec8 Extended)
	Number of Data 1 (Number of Total Records)	01
AVL Data	Timestamp	00 00 01 7C A6 B6 BF D8 (GMT: Friday, 22 October 2021 06:36:07)
	Priority	01
	Longitude	0F 0E 51 88
	Latitude	20 9A B4 82
	Altitude	00 86
	Angle	00 0A
	Satellites	0E
	Speed	00 00
	Event IO ID	00 00
	N of Total ID	00 06
	N1 of One Byte IO	00 00
	N2 of Two Bytes IO	00 02
	ID	00 19 (25 = BLE Temperature #1)
	Value	09 04 (2308=23.08°C)
	ID	00 56 (86 = BLE Humidity #1)
	Value	00 36 (24 %RHT)
	N4 of Four Bytes IO	00 03
	ID	01 CF (463 - BLE 1 Custom #2 = Movement status and movement events count)
	Value	00 00 00 16 (Currently not moving events count 22)
	ID	01 D0 (464 - BLE 1 Custom #3 = Angle )
	Value	00 00 FF 4D (Pitch = 0°, Roll = -179°)
	ID	01 D1 (465 - BLE 1 Custom #4 = Battery Voltage)
	Value	00 00 00 6D (109 = 2000 + 109 * 10 mV = 3090 mV)
	N8 of Eight Bytes IO	00 00
	NX of X Bytes IO	00 01
	N’th IO ID - AVL ID.	01 4B (331 - BLE 1 Custom #1 = Flags)
	Length of Variable Length IO	00 01
	Value of Variable Length IO	B7 = (MSB)11011 0111(LSB) It's parsed from least significant byte(LSB): Bit 0 – Temperature value presence. 1 Means device is reading and transmitting temperature value. Bit 1 – Humidity value presence. 1 Means device is reading and transmitting humidity value. Bit 2 – Magnetic sensor presence. 1 Means device is reading and transmitting Magnetic sensor value. Bit 3 – Magnetic sensor state 1 magnetic field is detected/0 magnetic field is not detected) Valid value is present only if bit 2 flag is set. Bit 4 – Movement sensor counter. 1 Means device is reading and transmitting movement state and count values. Bit 5 – Movement sensor angle. 1 Means device is reading and transmitting angle roll and pitch values. Bit 6 – Low Battery indication. 0 – Means device battery is from 100 to 15 % (When value changes to 1 Battery level is lower than 15 %. 7 – Battery voltage value presence. 1 Means device is reading and transmitting battery voltage value.
	Number of Data 2 (Number of Total Records)	01
	CRC-16	00 00 CF 7D

Safety information

This message contains information on how to operate BTSID1 safely. By following these requirements and recommendations, you will avoid dangerous situations. You must read these instructions carefully and follow them strictly before operating the device!

1. To avoid mechanical damage, it is advised to transport the device in an impact-proof package.

2. In case of malfunction contact yours Teltonika account manager or write to technical support team over VIP helpdesk.

External Links

Product Page:

https://teltonika-gps.com/eye/

Quick Manual:

Manual PDF