Teltonika Data Sending Protocols

Introduction

A codec is a device or computer program for encoding or decoding a digital data stream or signal. Codec is a portmanteau of coder-decoder. A codec encodes a data stream or a signal for transmission and storage, possibly in encrypted form, and the decoder function reverses the encoding for playback or editing.

Below you will see a table of all Codec types with ID’s:

Codec 8	Codec 8 Extended	Codec 16	Codec 12	Codec 13	Codec 14
0x08	0x8E	0x10	0x0C	0x0D	0x0E

Also, there are using two data transport protocols: TCP and UDP. But it is not important which one will be used in Codec.

Codec for device data sending

In this chapter, you will find information about every Codec protocol which are using for device data sending and differences between them.

Codec 8

• Protocol Overview

Codec8 – a main FM device protocol that is used for sending data to the server.

• Codec 8 protocol sending over TCP

TCP is a connection-oriented protocol that is used for communication between devices. The workings of this type of protocol is described below in the communication with server section.

• AVL Data Packet

Below table represents AVL Data Packet structure:

0x00000000 (Preamble)	Data Field Length	Codec ID	Number of Data 1	AVL Data	Number of Data 2	CRC-16
4 bytes	4 bytes	1 byte	1 byte	X bytes	1 byte	4 bytes

Preamble – the packet starts with four zero bytes.
Data Field Length – size is calculated starting from Codec ID to Number of Data 2.
Codec ID – in Codec8 it is always 0x08.
Number of Data 1 – a number which defines how many records are in the packet.
AVL Data – actual data in the packet (more information below).
Number of Data 2 – a number which defines how many records are in the packet. This number must be the same as “Number of Data 1”.
CRC-16 – calculated from Codec ID to the Second Number of Data. CRC (Cyclic Redundancy Check) is an error-detecting code using for detect accidental changes to RAW data. For calculation we are using CRC-16/IBM.

Note: for FMB630, FMB640 and FM63XY, minimum AVL record size is 45 bytes (all IO elements disabled). Maximum AVL record size is 255 bytes. Maximum AVL packet size is 512 bytes. For other devices, the minimum AVL record size is 45 bytes (all IO elements disabled). Maximum AVL packet size is 1280 bytes.

• AVL Data

The below table represents the AVL Data structure.

Timestamp	Priority	GPS Element	IO Element
8 bytes	1 byte	15 bytes	X bytes

Timestamp – a difference, in milliseconds, between the current time and midnight, January, 1970 UTC (UNIX time).
Priority – field which define AVL data priority (more information below).
GPS Element – location information of the AVL data (more information below).
IO Element – additional configurable information from device (more information below).

• Priority

The below table represents Priority values. Packet priority depends on device configuration and records sent.

Priority
0	Low
1	High
2	Panic

• GPS element

Below table represents GPS Element structure:

Longitude	Latitude	Altitude	Angle	Satellites	Speed
4 bytes	4 bytes	2 bytes	2 bytes	1 byte	2 bytes

Longitude – east – west position.
Latitude – north – south position.
Altitude – meters above sea level.
Angle – degrees from north pole.
Satellites – number of satellites in use.
Speed – speed calculated from satellites.

Note: Speed will be 0x0000 if GPS data is invalid.

Longitude and latitude are integer values built from degrees, minutes, seconds and milliseconds by formula:

Where:
d – Degrees; m – Minutes; s – Seconds; ms – Milliseconds; p – Precision (10000000)
If longitude is in west or latitude in south, multiply result by –1.

Note:
To determine if the coordinate is negative, convert it to binary format and check the very first bit. If it is 0, coordinate is positive, if it is 1, coordinate is negative.

Example:
Received value: 20 9C CA 80 converted to BIN: 00100000 10011100 11001010 10000000 first bit is 0, which means coordinate is positive converted to DEC: 547146368. For more information see two‘s complement arithmetic.

• IO Element

Event IO ID	1 byte		Event IO ID – if data is acquired on event – this field defines which IO property has changed and generated an event. For example, when if Ignition state changed and it generate event, Event IO ID will be 0xEF (AVL ID: 239). If it’s not eventual record – the value is 0. N – a total number of properties coming with record (N = N1 + N2 + N4 + N8). N1 – number of properties, which length is 1 byte. N2 – number of properties, which length is 2 bytes. N4 – number of properties, which length is 4 bytes. N8 – number of properties, which length is 8 bytes. N’th IO ID - AVL ID. N’th IO Value - AVL ID value.
N of Total IO	1 byte
N1 of One Byte IO	1 byte
1’st IO ID	1 byte
1’st IO Value	1 byte
...
N1’th IO ID	1 byte
N1’th IO Value	1 byte
N2 of Two Bytes	1 byte
1’st IO ID	1 byte
1’st IO Value	2 bytes
...
N2’th IO ID	1 byte
N2’th IO Value	2 bytes
N4 of Four Bytes	1 byte
1’st IO ID	1 byte
1’st IO Value	4 bytes
...
N4’th IO ID	1 byte
N4’th IO Value	4 byte
N8 of Eight Bytes	1 byte
1’st IO ID	1 byte
1’st IO Value	8 byte
...
N8’IO ID	1 byte
N8’IO Value	8 bytes

• Communication with server

First, when the module connects to the server, the module sends its IMEI. First comes a short identifying the number of bytes written and then goes IMEI as text (bytes).
For example, IMEI 356307042441013 would be sent as 000F333536333037303432343431303133.
First two bytes denote IMEI length. In this case 0x000F means, that IMEI is 15 bytes long.
After receiving IMEI, server should determine if it would accept data from this module. If yes, server will reply to module 01, if not - 00. Note that confirmation should be sent as binary packet. I.e. 1 byte 0x01 or 0x00.
Then the module starts to send the first AVL data packet. After the server receives a packet and parses it, the server must report to the module number of data received as integer (four bytes).
If sent data number and reported by the server doesn’t match module resends sent data.

• Example:
  

Module connects to server and sends IMEI:
000F333536333037303432343431303133
Server accepts the module:
01
Module sends data packet:

AVL Data Packet Header	AVL Data Array	CRC-16
Four Zero Bytes – 0x00000000, “AVL Data Array” length – 0x000000FE	Codec ID – 0x08, Number of Data – 0x02 (Encoded using continuous bit stream. Last byte padded to align to byte boundary)	CRC of “AVL Data Array”
00000000000000FE	0802...(data elements)...02	00008612

Server acknowledges data reception (2 data elements): 00000002

• Examples

Hexadecimal stream of AVL Data Packet receiving and response in these examples are given in hexadecimal form. The different fields of packets are separated into different table columns for better readability and some of them are converted to ASCII values for better understanding.

1'st example
Receiving one data record with each element property (1 byte, 2 bytes, 4 byte and 8 byte).

Received data in hexadecimal stream:
000000000000003608010000016B40D8EA30010000000000000000000000000000000105021503010101425E0F01F10000601A014E0000000000000000010000C7CF

Parsed:

AVL Data Packet
AVL Data Packet Part		HEX Code Part
	Zero Bytes	00 00 00 00
	Data Field Length	00 00 00 36
	Codec ID	08
	Number of Data 1 (Records)	01
AVL Data	Timestamp	00 00 00 01 6B 40 D8 EA 30 (GMT: Monday, June 10, 2019 10:04:46 AM)
	Priority	01
	Longitude	00 00 00 00
	Latitude	00 00 00 00
	Altitude	00 00
	Angle	00 00
	Satellites	00
	Speed	00 00
	Event IO ID	01
	N of Total ID	05
	N1 of One Byte IO	02
	1’st IO ID	15 (AVL ID: 21, Name: GSM Signal)
	1’st IO Value	03
	2’nd IO ID	01 (AVL ID: 1, Name: DIN1)
	2’nd IO Value	01
	N2 of Two Bytes IO	01
	1’st IO ID	42 (AVL ID: 66, Name: External Voltage)
	1’st IO Value	5E 0F
	N4 of Four Bytes IO	01
	1’st IO ID	F1 (AVL ID: 241, Name: Active GSM Operator)
	1’st IO Value	00 00 60 1A
	N8 of Eight Bytes IO	01
	1’st IO ID	4E (AVL ID: 78, Name: iButton)
	1’st IO Value	00 00 00 00 00 00 00 00
	Number of Data 2 (Number of Total Records)	01
	CRC-16	00 00 C7 CF

Server response: 00000001

2'nd example
Receiving one data record with one or two different element properties (1 byte, 2 byte).

Received data in hexadecimal stream:
000000000000002808010000016B40D9AD80010000000000000000000000000000000103021503010101425E100000010000F22A

Parsed:

AVL Data Packet
AVL Data Packet Part		HEX Code Part
	Zero Bytes	00 00 00 00
	Data Field Length	00 00 00 28
	Codec ID	08
	Number of Data 1 (Records)	01
AVL Data	Timestamp	00 00 01 6B 40 D9 AD 80 (GMT: Monday, June 10, 2019 10:05:36 AM)
	Priority	01
	Longitude	00 00 00 00
	Latitude	00 00 00 00
	Altitude	00 00
	Angle	00 00
	Satellites	00
	Speed	00 00
	Event IO ID	01
	N of Total ID	03
	N1 of One Byte IO	02
	1’st IO ID	15 (AVL ID: 21, Name: GSM Signal)
	1’st IO Value	03
	2’nd IO ID	01 (AVL ID: 1, Name: DIN1)
	2’nd IO Value	01
	N2 of Two Bytes IO	01
	1’st IO ID	42 (AVL ID: 66, Name: External Voltage)
	1’st IO Value	5E 0F
	N4 of Four Bytes IO	00
	N8 of Eight Bytes IO	00
	Number of Data 2 (Number of Total Records)	01
	CRC-16	00 00 F2 2A

Server response: 00000001

3'rd example
Receiving two or more data records with one or more different element properties.

Received data in hexadecimal stream:
000000000000004308020000016B40D57B480100000000000000000000000000000001010101000000000000016B40D5C198010000000000000000000000000000000 101010101000000020000252C

Parsed:

AVL Data Packet
AVL Data Packet Part		HEX Code Part
	Zero Bytes	00 00 00 00
	Data Field Length	00 00 00 43
	Codec ID	08
	Number of Data 1 (Records)	02
AVL Data (1'st record)	Timestamp	00 00 01 6B 40 D5 7B 48 (GMT: Monday, June 10, 2019 10:01:01 AM)
	Priority	01
	Longitude	00 00 00 00
	Latitude	00 00 00 00
	Altitude	00 00
	Angle	00 00
	Satellites	00
	Speed	00 00
	Event IO ID	01
	N of Total ID	01
	N1 of One Byte IO	01
	1’st IO ID	01 (AVL ID: 1, Name: DIN1)
	1’st IO Value	00
	N2 of Two Bytes IO	00
	N4 of Four Bytes IO	00
	N8 of Eight Bytes IO	00
AVL Data (2'nd record)	Timestamp	00 00 01 6B 40 D5 C1 98 (GMT: Monday, June 10, 2019 10:01:19 AM)
	Priority	01
	Longitude	00 00 00 00
	Latitude	00 00 00 00
	Altitude	00 00
	Angle	00 00
	Satellites	00
	Speed	00 00
	Event IO ID	01
	N of Total ID	01
	N1 of One Byte IO	01
	1’st IO ID	01 (AVL ID: 1, Name: DIN1)
	1’st IO Value	01
	N2 of Two Bytes IO	00
	N4 of Four Bytes IO	00
	N8 of Eight Bytes IO	00
	Number of Data 2 (Number of Total Records)	02
	CRC-16	00 00 25 2C

Server response: 00000002

• Codec8 protocol sending over UDP

Codec8 protocol [over UDP] is a transport layer protocol above UDP/IP to add reliability to plain UDP/IP using acknowledgment packets.

• AVL Data Packet

The packet structure is as follows:

UDP Datagram
Example	2 bytes
Packet ID	2 bytes
Not Usable Byte	1 byte
Packet Payload	Variable

Example – packet length (excluding this field) in big ending byte order.
Packet ID – packet ID unique for this channel.
Not Usable Byte – not usable byte.
Packet payload – data payload.

• Acknowledgment packet

Acknowledgment packet should have the same Packet ID as an acknowledged data packet and empty Data Payload. Acknowledgment should be sent in binary format.

Acknowledgment Packet
Packet Length	Packet ID	Not Usable Byte
2 bytes	2 bytes	1 byte

Packet Length – packet length by sending/response data.
Packet ID – same as in acknowledgment packet.
Not Usable Byte – always will be 0x01.

• Sending AVL Packet Payload using UDP channel

The below table represents the Sending Packet Payload structure.

AVL data encapsulated in UDP channel packet
AVL Packet ID	IMEI Length	Module IMEI	AVL Data Array
1 byte	2 bytes	15 bytes	X bytes

AVL Packet ID – ID identifying this AVL packet.
IMEI Length – always will be 0x000F.
Module IMEI – IMEI of a sending module encoded the same as with TCP.
AVL Data Array – array of encoded AVL data (same as TCP AVL Data Array).

• Server response Packet Payload using UDP channel

The below table represents the Server Response Packet Payload structure.

Server Response to AVL Data Packet
AVL Packet ID	Number of Accepted AVL Elements
1 byte	1 byte

• Communication with server

The module sends the UDP channel packet with an encapsulated AVL data packet. The server sends the UDP channel packet with an encapsulated response module that validates AVL Packet ID and the Number of accepted AVL elements. If server response with valid AVL Packet ID is not received within configured timeout, the module can retry sending.

• Example:

Module sends the data:

UDP Channel Header	AVL Packet Header	AVL Data Array
Length – 0x00FE, Packet ID – 0xCAFE Not Usable Byte – 0x01	AVL Packet ID – 0xDD, IMEI Length – 0x000F IMEI – 0x313233343536373839303132333435 (Encoded using continuous bit stream. Last byte padded to align to byte boundary)	Codec ID – 0x08, Number of Data – 0x02 (Encoded using continuous bit stream)
00FECAFE01	DD000F3133343536373839303132333435	0802…(data elements)…02

Server must respond with acknowledgment:

UDP Channel Header	AVL Packet Acknowledgment
Length – 0x0005, Packet ID – 0xCAFE, Not Usable Byte – 0x01	AVL Packet ID – 0xDD, Number of Accepted Data – 0x02
0005CAFE01	DD02

• Example

Hexadecimal stream of AVL Data Packet receiving and response in this example are given in hexadecimal form. The different fields of packet are separate into different table columns for better readability and some of them are converted to ASCII values for better understanding.

Received data in hexadecimal stream:
003DCAFE0105000F33353230393330383634303336353508010000016B4F815B30010000000000000000000000000000000103021503010101425DBC000001

Parsed:

AVL Data Packet
AVL Data Packet Part		HEX Code Part
UDP Channel Header	Length	00 3D
	Packet ID	CA FE
	Not usable byte	01
AVL Packet Header	AVL packet ID	05
	IMEI Length	00 0F
	IMEI	33 35 32 30 39 33 30 38 36 34 30 33 36 35 35
AVL Data Array	Codec ID	08
	Number of Data 1 (Records)	01
	Timestamp	00 00 01 6B 4F 81 5B 30 (GMT: Thursday, June 13, 2019 6:23:26 AM)
	Priority	01
	Longitude	00 00 00 00
	Latitude	00 00 00 00
	Altitude	00 00
	Angle	00 00
	Satellites	00
	Speed	00 00
	Event IO ID	01
	N of Total ID	03
	N1 of One Byte IO	02
	1’st IO ID	15 (AVL ID: 21, Name: GSM Signal)
	1’st IO Value	03
	2’nd IO ID	01 (AVL ID: 1, Name: DIN1)
	2’nd IO Value	01
	N2 of Two Bytes IO	01
	1’st IO ID	42 (AVL ID: 66, Name: External Voltage)
	1’st IO Value	5D BC
	N4 of Four Bytes IO	00
	N8 of EightBytes IO	00
	Number of Data 2 (Number of Total Records)	01

Server response in hexadecimal stream: 0005CAFE010501

Parsed:

Server Response to AVL Data Packet
Server Response Part		HEX Code Part
UDP Channel Header	Length	00 05
	Packet ID	CA FE
	Not usable byte	01
AVL Packet Acknowledgment	AVL packet ID	05
	Number of Accepted Data	01

Codec 8 Extended

• Protocols overview

Codec8 Extended is used for FMBXXX family devices. This protocol looks familiar to Codec8 but they have some differences. Main differences between are shown in below table:

	Codec8	Codec8 Extended
Codec ID	0x08	0x8E
AVL Data IO element length	1 byte	2 bytes
AVL Data IO element total IO count length	1 byte	2 bytes
AVL Data IO element IO count length	1 byte	2 bytes
AVL Data IO element AVL ID length	1 byte	2 bytes
Variable size IO elements	Does not include	Includes variable size elements

• Codec 8 Extended protocol sending over TCP

• AVL data packet

Below table represents AVL data packet structure:

0x00000000 (Preamble)	Data Field Length	Codec ID	Number of Data 1	AVL Data	Number of Data 2	CRC-16
4 bytes	4 bytes	1 byte	1 byte	X bytes	1 byte	4 bytes

Preamble – the packet starts with four zero bytes.
Data Field Length – size is calculated starting from Codec ID to Number of Data 2.
Codec ID – in Codec8 Extended it is always 0x8E.
Number of Data 1 – a number which defines how many records are in the packet.
AVL Data – actual data in the packet (more information below).
Number of Data 2 – a number which defines how many records are in the packet. This number must be the same as “Number of Data 1”.
CRC-16 – calculated from Codec ID to the Second Number of Data. CRC (Cyclic Redundancy Check) is an error-detecting code using for detect accidental changes to RAW data. For calculation we are using CRC-16/IBM.

Note: for FMB630, FMB640 and FM63XY, minimum AVL record size is 45 bytes (all IO elements disabled). Maximum AVL record size is 255 bytes. For other devices, the minimum AVL record size is 45 bytes (all IO elements disabled). Maximum AVL packet size is 1280 bytes.

• AVL Data

Below table represents AVL Data structure:

Timestamp	Priority	GPS Element	IO Element
8 bytes	1 byte	15 bytes	X bytes

Timestamp – a difference, in milliseconds, between the current time and midnight, January 1970 UTC (UNIX time).
Priority – field which define AVL data priority (more information below).
GPS Element – locational information of the AVL data (more information below).
IO Element – additional configurable information from device (more information below).

• Priority

The below table represents Priority values. Packet priority depends on device configuration and records sent.

Priority
0	Low
1	High
2	Panic

• GPS element

Below table represents GPS Element structure:

Longitude	Latitude	Altitude	Angle	Satellites	Speed
4 bytes	4 bytes	2 bytes	2 bytes	1 byte	2 bytes

Longitude – east – west position.
Latitude – north – south position.
Altitude – meters above sea level.
Angle – degrees from north pole.
Satellites – number of satellites in use.
Speed – speed calculated from satellites.

Note: Speed will be 0x0000 if GPS data is invalid.

Longitude and latitude are integer values built from degrees, minutes, seconds and milliseconds by formula:

Where:
d – Degrees; m – Minutes; s – Seconds; ms – Milliseconds; p – Precision (10000000)
If longitude is in west or latitude in south, multiply result by –1.

Note:
To determine if the coordinate is negative, convert it to binary format and check the very first bit. If it is 0, coordinate is positive, if it is 1, coordinate is negative.

Example:
Received value: 20 9C CA 80 converted to BIN: 00100000 10011100 11001010 10000000 first bit is 0, which means coordinate is positive converted to DEC: 547146368. For more information see two‘s complement arithmetic.

• IO Element

Event IO ID	2 bytes		Event IO ID – if data is acquired on event – this field defines which IO property has changed and generated an event. For example, when if Ignition state changed and it generate event, Event IO ID will be 0xEF (AVL ID: 239). If it’s not eventual record – the value is 0. N – a total number of properties coming with record (N = N1 + N2 + N4 + N8). N1 – number of properties, which length is 1 byte. N2 – number of properties, which length is 2 bytes. N4 – number of properties, which length is 4 bytes. N8 – number of properties, which length is 8 bytes. NX – a number of properties, which length is defined by length element. N’th IO ID - AVL ID. N'th Lenght - AVL ID value lenght. N’th IO Value - AVL ID value.
N of Total IO	2 bytes
N1 of One Byte IO	2 bytes
1’st IO ID	2 bytes
1’st IO Value	1 byte
...
N1’th IO ID	2 bytes
N1’th IO Value	1 byte
N2 of Two Bytes	2 bytes
1’st IO ID	2 bytes
1’st IO Value	2 bytes
...
N2’th IO ID	2 bytes
N2’th IO Value	2 bytes
N4 of Four Bytes	2 bytes
1’st IO ID	2 bytes
1’st IO Value	4 bytes
...
N4’th IO ID	2 bytes
N4’th IO Value	4 byte
N8 of Eight Bytes	2 bytes
1’st IO ID	2 bytes
1’st IO Value	8 byte
...
N8’IO ID	2 bytes
N8’IO Value	8 bytes
NX of X Byte IO	2 bytes
1’st IO ID	2 bytes
1’st IO Length	2 bytes
1’st IO Value	Defined by lenght
...
NX’th IO ID	2 bytes
NX’th Length	2 bytes
NX’th Value	Defined by lenght

• Communication with server

Communication with the server is the same as with the Codec8 protocol, except in Codec8 Extended protocol Codec ID is 0x8E.

• Example:

Module connects to server and sends IMEI:
000F333536333037303432343431303133
Server accepts the module:
01
Module sends data packet:

AVL Data Packet Header	AVL Data Array	CRC-16
Four Zero Bytes – 0x00000000, “AVL Data Array” length – 0x000000FE	Codec ID – 0x8E, Number of Data – 0x02 (Encoded using continuous bit stream. Last byte padded to align to byte boundary)	CRC of “AVL Data Array”
00000000000000FE	8E02...(data elements)...02	00008612

Server acknowledges data reception (2 data elements): 00000002

• Example

Hexadecimal stream of AVL Data Packet receiving and response in this example are given in hexadecimal form. The different fields of packet are separate into different table columns for better readability and some of them are converted to ASCII values for better understanding.

Received data in hexadecimal stream:
000000000000004A8E010000016B412CEE000100000000000000000000000000000000010005000100010100010011001D00010010015E2C880002000B000000003544C87 A000E000000001DD7E06A00000100002994

Parsed data:

AVL Data Packet
AVL Data Packet Part		HEX Code Part
	Zero Bytes	00 00 00 00
	Data Field Length	00 00 00 4A
	Codec ID	8E
	Number of Data 1 (Records)	01
AVL Data	Timestamp	00 00 01 6B 41 2C EE 00 (GMT: Monday, June 10, 2019 11:36:32 AM)
	Priority	01
	Longitude	00 00 00 00
	Latitude	00 00 00 00
	Altitude	00 00
	Angle	00 00
	Satellites	00
	Speed	00 00
	Event IO ID	00 01
	N of Total ID	00 05
	N1 of One Byte IO	00 01
	1’st IO ID	00 01 (AVL ID: 1, Name: DIN1)
	1’st IO Value	01
	N2 of Two Bytes IO	00 01
	1’st IO ID	00 11 (AVL ID: 17, Name: Axis X)
	1’st IO Value	00 1D
	N4 of Four Bytes IO	00 01
	1’st IO ID	00 10 (AVL ID: 16, Name: Total Odometer)
	1’st IO Value	01 5E 2C 88
	N8 of Eight Bytes IO	00 02
	1’st IO ID	00 0B (AVL ID: 11, Name: ICCID1)
	1’st IO Value	00 00 00 00 35 44 C8 7A
	2’nd IO ID	00 0E (AVL ID: 14, Name: ICCID2)
	2’nd IO Value	00 00 00 00 1D D7 E0 6A
	NX of X Byte IO	00 00
	Number of Data 2 (Number of Total Records)	01
	CRC-16	00 00 29 94

Server response: 00000001

• Codec8 Extended protocol sending over UDP

• UDP channel protocol

AVL data packet is the same as with Codec8, except Codec ID is changed to 0x8E. AVL Data encoding was performed according to Codec8 Extended protocol.

• Communication with server

The module sends the UDP channel packet with an encapsulated AVL data packet. The server sends the UDP channel packet with an encapsulated response module that validates AVL Packet ID and the Number of accepted AVL elements. If server response with valid AVL Packet ID is not received within configured timeout, the module can retry sending.

• Example:

Module sends the data:

UDP Channel Header	AVL Packet Header	AVL Data Array
Length – 0x00FE, Packet ID – 0xCAFE Not Usable Byte – 0x01	AVL Packet ID – 0xDD, IMEI Length – 0x000F IMEI – 0x313233343536373839303132333435 (Encoded using continuous bit stream. Last byte padded to align to byte boundary)	Codec ID – 0x8E, Number of Data – 0x02 (Encoded using continuous bit stream)
00FECAFE01	DD000F3133343536373839303132333435	8E02…(data elements)…02

Server must respond with acknowledgment:

UDP Channel Header	AVL Packet Acknowledgment
Length – 0x0005, Packet ID – 0xCAFE, Not Usable Byte – 0x01	AVL Packet ID – 0xDD, Number of Accepted Data – 0x02
0005CAFE01	DD02

• Example

Hexadecimal stream of AVL Data Packet receiving and response in this example are given in hexadecimal form. The different fields of packet are separate into different table columns for better readability and some of them are converted to ASCII values for better understanding.

Received data in hexadecimal stream:
005FCAFE0107000F3335323039333038363430333635358E010000016B4F831C680100000000000000000000000000000000010005000100010100010011009D000100 10015E2C880002000B000000003544C87A000E000000001DD7E06A000001

Parsed:

AVL Data Packet
AVL Data Packet Part		HEX Code Part
UDP Channel Header	Length	00 5F
	Packet ID	CA FE
	Not usable byte	01
AVL Packet Header	AVL packet ID	07
	IMEI Length	00 0F
	IMEI	33 35 32 30 39 33 30 38 36 34 30 33 36 35 35
AVL Data Array	Codec ID	8E
	Number of Data 1 (Records)	01
	Timestamp	00 00 01 6B 4F 83 1C 68 (GMT: Thursday, June 13, 2019 6:25:21 AM)
	Priority	01
	Longitude	00 00 00 00
	Latitude	00 00 00 00
	Altitude	00 00
	Angle	00 00
	Satellites	00
	Speed	00 00
	Event IO ID	00 01
	N of Total ID	00 05
	N1 of One Byte IO	00 01
	1’st IO ID	00 01 (AVL ID: 1, Name: DIN1)
	1’st IO Value	00 01
	N2 of Two Bytes IO	00 01
	1’st IO ID	00 11 (AVL ID: 17, Name: Axis X)
	1’st IO Value	00 1D
	N4 of Four Bytes IO	00 01
	1’st IO ID	00 10 (AVL ID: 16, Name: Total Odometer)
	1’st IO Value	01 5E 2C 88
	N8 of Eight Bytes IO	00 02
	1’st IO ID	00 0B (AVL ID: 11, Name: ICCID1)
	1’st IO Value	00 00 00 00 35 44 C8 7A
	2’nd IO ID	00 0E (AVL ID: 14, Name: ICCID2)
	2’nd IO Value	00 00 00 00 1D D7 E0 6A
	NX of X Byte IO	00 00

Server response in hexadecimal stream: 0005CAFE010701

Parsed:

Server Response to AVL Data Packet
Server Response Part		HEX Code Part
UDP Channel Header	Length	00 05
	Packet ID	CA FE
	Not usable byte	01
AVL Packet Acknowledgment	AVL packet ID	07
	Number of Accepted Data	01

Codec 16

• Protocol overview

Codec16 is using for FMB630/FM63XY devices. This protocol looks familiar like Codec8 but they have some differences. Main differences between are shown in table below:

	Codec8	Codec16
Codec ID	0x08	0x10
AVL Data IO element ID event length	1 byte	2 bytes
AVL Data IO element AVL ID length	1 byte	2 bytes
Generation Type	Not Using	Is Using

Note: Codec16 is supported from firmware – 00.03.xx and newer. (FMB630/FM63XY) || AVL ID‘s which are higher than 255 will can be used only in Codec16 protocol.

• Codec 16 protocol sending over TCP

• AVL data packet

Below table represents AVL data packet structure:

0x00000000 (Preamble)	Data Field Length	Codec ID	Number of Data 1	AVL Data	Number of Data 2	CRC-16
4 bytes	4 bytes	1 byte	1 byte	X bytes	1 byte	4 bytes

Preamble – the packet starts with four zero bytes.
Data Field Length – size is calculated starting from Codec ID to Number of Data 2.
Codec ID – in Codec16 it is always 0x10.
Number of Data 1 – a number which defines how many records are in the packet.
AVL Data – actual data in the packet (more information below).
Number of Data 2 – a number which defines how many records are in the packet. This number must be the same as “Number of Data 1”.
CRC-16 – calculated from Codec ID to the Second Number of Data. CRC (Cyclic Redundancy Check) is an error-detecting code using for detect accidental changes to RAW data. For calculation we are using CRC-16/IBM.

Note: for FMB630 and FM63XY, minimum AVL record size is 45 bytes (all IO elements disabled). Maximum AVL record size is 255 bytes.

• AVL Data

Below table represents AVL Data structure:

Timestamp	Priority	GPS Element	IO Element
8 bytes	1 byte	15 bytes	X bytes

Timestamp – a difference, in milliseconds, between the current time and midnight, January 1970 UTC (UNIX time).
Priority – field which define AVL data priority (more information below).
GPS Element – location information of the AVL data (more information below).
IO Element – additional configurable information from device (more information below).

• Priority

The below table represents Priority values. Packet priority depends on device configuration and records sent.

Priority
0	Low
1	High
2	Panic

• GPS element

Below table represents GPS Element structure:

Longitude	Latitude	Altitude	Angle	Satellites	Speed
4 bytes	4 bytes	2 bytes	2 bytes	1 byte	2 bytes

Longitude – east – west position.
Latitude – north – south position.
Altitude – meters above sea level.
Angle – degrees from north pole.
Satellites – number of satellites in use.
Speed – speed calculated from satellites.

Note: Speed will be 0x0000 if GPS data is invalid.

Longitude and latitude are integer values built from degrees, minutes, seconds and milliseconds by formula:

Where:
d – Degrees; m – Minutes; s – Seconds; ms – Milliseconds; p – Precision (10000000)
If longitude is in west or latitude in south, multiply result by –1.

Note:
To determine if the coordinate is negative, convert it to binary format and check the very first bit. If it is 0, coordinate is positive, if it is 1, coordinate is negative.

Example:
Received value: 20 9C CA 80 converted to BIN: 00100000 10011100 11001010 10000000 first bit is 0, which means coordinate is positive converted to DEC: 547146368. For more information see two‘s complement arithmetic.

• IO Element

Event IO ID	2 bytes		Event IO ID – if data is acquired on event – this field defines which IO property has changed and generated an event. For example, when if Ignition state changed and it generate event, Event IO ID will be 0xEF (AVL ID: 239). If it’s not eventual record – the value is 0. Generation type - data event generation type. More information about it you can find here. N – a total number of properties coming with record (N = N1 + N2 + N4 + N8). N1 – number of properties, which length is 1 byte. N2 – number of properties, which length is 2 bytes. N4 – number of properties, which length is 4 bytes. N8 – number of properties, which length is 8 bytes. N’th IO ID - AVL ID. N’th IO Value - AVL ID value.
Generation Type	1 byte
N of Total IO	1 byte
N1 of One Byte IO	1 byte
1’st IO ID	2 bytes
1’st IO Value	1 byte
...
N1’th IO ID	2 bytes
N1’th IO Value	1 byte
N2 of Two Bytes	1 byte
1’st IO ID	2 bytes
1’st IO Value	2 bytes
...
N2’th IO ID	2 bytes
N2’th IO Value	2 bytes
N4 of Four Bytes	1 byte
1’st IO ID	2 bytes
1’st IO Value	4 bytes
...
N4’th IO ID	2 bytes
N4’th IO Value	4 byte
N8 of Eight Bytes	1 byte
1’st IO ID	2 bytes
1’st IO Value	8 byte
...
N8’IO ID	2 bytes
N8’IO Value	8 bytes

• Generation type

Value	Record Created
0	On Exit
1	On Entrance
2	On Both
3	Reserved
4	Hysteresis
5	On Change
6	Eventual
7	Periodical

• Communication with server

Communication with server is the same as with Codec8 protocol, except in Codec16 protocol Codec ID is 0x10 and has generation type.

• Example:

Module connects to server and sends IMEI:
000F333536333037303432343431303133
Server accepts the module:
01
Module sends data packet:

AVL Data Packet Header	AVL Data Array	CRC-16
Four Zero Bytes – 0x00000000, “AVL Data Array” length – 0x000000FE	Codec ID – 0x10, Number of Data – 0x02 (Encoded using continuous bit stream. The last byte padded to align to byte boundary)	CRC of “AVL Data Array”
00000000000000FE	1002...(data elements)...02	00008612

Server acknowledges data reception (2 data elements): 00000002

• Example

Hexadecimal stream of AVL Data Packet receiving and response in this example are given in hexadecimal form. The different fields of packet are separate into different table columns for better readability and some of them are converted to ASCII values for better understanding.

Received data in hexadecimal stream:
000000000000005F10020000016BDBC7833000000000000000000000000000000000000B05040200010000030002000B00270042563A00000000016BDBC78718 00000000000000000000000000000000000B05040200010000030002000B00260042563A00000200005FB3

Parsed data:

AVL Data Packet
AVL Data Packet Part		HEX Code Part
	Zero Bytes	00 00 00 00
	Data Field Length	00 00 00 5F
	Codec ID	10
	Number of Data 1 (Records)	02
AVL Data (1'st record)	Timestamp	00 00 01 6B DB C7 83 30 (GMT: Wednesday, July 10, 2019 12:06:54 PM)
	Priority	01
	Longitude	00 00 00 00
	Latitude	00 00 00 00
	Altitude	00 00
	Angle	00 00
	Satellites	00
	Speed	00 00
	Event IO ID	00 0B
	Generation Type	05
	N of Total ID	04
	N1 of One Byte IO	02
	1’st IO ID	00 01 (AVL ID: 1, Name: DIN1)
	1’st IO Value	00
	2’nd IO ID	00 03 (AVL ID: 3, Name: DIN3)
	2’nd IO Value	00
	N2 of Two Bytes IO	02
	1’st IO ID	00 0B (AVL ID: 11, Name: ICCID1)
	1’st IO Value	00 27
	2’nd IO ID	00 42 (AVL ID: 66, Name: External Voltage)
	2’nd IO Value	56 3A
	N4 of Four Bytes IO	00
	N8 of Eight Bytes IO	00
AVL Data (2'nd record)	Timestamp	00 00 01 6B DB C7 87 18 (GMT: Wednesday, July 10, 2019 12:06:55 PM)
	Priority	01
	Longitude	00 00 00 00
	Latitude	00 00 00 00
	Altitude	00 00
	Angle	00 00
	Satellites	00
	Speed	00 00
	Event IO ID	00 0B
	Generation Type	05
	N of Total ID	04
	N1 of One Byte IO	02
	1’st IO ID	00 01 (AVL ID: 1, Name: DIN1)
	1’st IO Value	00
	2’nd IO ID	00 03 (AVL ID: 3, Name: DIN3)
	2’nd IO Value	00
	N2 of Two Bytes IO	02
	1’st IO ID	00 0B (AVL ID: 11, Name: ICCID1)
	1’st IO Value	00 26
	2’nd IO ID	00 42 (AVL ID: 66, Name: External Voltage)
	2’nd IO Value	56 3A
	N4 of Four Bytes IO	00
	N8 of Eight Bytes IO	00
	Number of Data 2 (Number of Total Records)	02
	CRC-16	00 00 5F B3

Server response: 00000002

• Codec16 protocol sending over UDP
• UDP channel protocol

AVL data packet is the same as with Codec8, except Codec ID is changed to 0x10. AVL Data encoding performed according to Codec16 protocol.

• Communication with server

The module sends the UDP channel packet with an encapsulated AVL data packet. The server sends the UDP channel packet with an encapsulated response module validates AVL Packet ID and the Number of accepted AVL elements. If server response with valid AVL Packet ID is not received within configured timeout, the module can retry sending.

• Example:

Module sends the data:

UDP Channel Header	AVL Packet Header	AVL Data Array
Length – 0x00FE, Packet ID – 0xCAFE Not Usable Byte – 0x01	AVL Packet ID – 0xDD, IMEI Length – 0x000F IMEI – 0x313233343536373839303132333435 (Encoded using continuous bit stream. Last byte padded to align to byte boundary)	Codec ID – 0x10, Number of Data – 0x02 (Encoded using continuous bit stream)
00FECAFE01	DD000F3133343536373839303132333435	1002…(data elements)…02

Server must respond with acknowledgment:

UDP Channel Header	AVL Packet Acknowledgment
Length – 0x0005, Packet ID – 0xCAFE, Not Usable Byte – 0x01	AVL Packet ID – 0xDD, Number of Accepted Data – 0x02
0005CAFE01	DD02

• Example

Hexadecimal stream of AVL Data Packet receiving and response in this example are given in hexadecimal form. The different fields of packet are separate into different table columns for better readability and some of them are converted to ASCII values for better understanding.

Received data in hexadecimal stream:
015BCAFE0101000F33353230393430383532333135393210070000015117E40FE80000000000000000000000000000000000EF05050400010000030000B4000 0EF01010042111A000001

Parsed:

AVL Data Packet
AVL Data Packet Part		HEX Code Part
UDP Channel Header	Length	01 5B
	Packet ID	CA FE
	Not usable byte	01
AVL Packet Header	AVL packet ID	07
	IMEI Length	00 0F
	IMEI	33 35 32 30 39 34 30 38 35 32 33 31 35 39 32
AVL Data Array	Codec ID	10
	Number of Data 1 (Records)	01
	Timestamp	00 00 01 51 17 E4 0F E8 (GMT: Wednesday, November 18, 2015 12:00:01 AM)
	Priority	00
	Longitude	00 00 00 00
	Latitude	00 00 00 00
	Altitude	00 00
	Angle	00 00
	Satellites	00
	Speed	00 00
	Event IO ID	00 EF
	Generation type	05
	N of Total ID	05
	N1 of One Byte IO	04
	1’st IO ID	00 01 (AVL ID: 1, Name: DIN1)
	1’st IO Value	00
	2’nd IO ID	00 03 (AVL ID: 3, Name: DIN3)
	2’nd IO Value	00
	3’rd IO ID	00 B4 (AVL ID: 180, Name: DOUT2)
	3’rd IO Value	00
	4’th IO ID	00 EF (AVL ID: 239, Name: Ignition)
	4’th IO Value	00
	N2 of Two Bytes IO	01
	1’st IO ID	42 (AVL ID: 66, Name: External Voltage)
	1’st IO Value	11 1A
	N4 of Four Bytes IO	00
	N8 of Eight Bytes IO	00
	Number of Data 2 (Number of Total Records)	01

Server response in hexadecimal stream: 0005CAFE010700

Parsed:

Server Response to AVL Data Packet
Server Response Part		HEX Code Part
UDP Channel Header	Length	00 05
	Packet ID	CA FE
	Not usable byte	01
AVL Packet Acknowledgment	AVL packet ID	07
	Number of Accepted Data	00

Differences between Codec 8, Codec 8 Extended and Codec 16

In the table below you will see differences between Codec8, Codec8 Extended, and Codec16.

	Codec8	Codec8 Extended	Codec16
Codec ID	0x08	0x8E	0x10
AVL Data IO element length	1 byte	2 bytes	2 bytes
AVL Data IO element total IO count length	1 byte	2 bytes	2 bytes
Generation Type	Is Using	Not Using	Is Using
AVL Data IO element IO count length	1 byte	2 bytes	1 byte
AVL Data IO element AVL ID length	1 byte	2 bytes	2 bytes
Variable size IO elements	Does not include	Includes variable size elements	Does not include

Codec for communication over GPRS messages

In this chapter, you will find information about every Codec protocol which are using for communication over GPRS messages and differences between them.

Codec 12

• About Codec12

Codec12 is the original and main Teltonika protocol for device-server communication over GPRS messages. Codec12 GPRS commands can be used for sending configuration, debug, digital outputs control commands, or other (special purpose command on special firmware versions). This protocol is also necessary for using FMB630/FM6300/FM5300/FM5500/FM4200 features like: Garmin, LCD communication, COM TCP Link Mode.

• GPRS command session

The following figure shows how the GRPS command session is started over TCP.
First, the Teltonika device opens the GPRS session and sends AVL data to the server (refer device protocols). Once all records are sent and correct sent data array acknowledgment is received by device then GPRS commands in Hex can be sent to the device.
The ACK (acknowledge of IMEI from server) is a one-byte constant 0x01. The acknowledgment of each data array send from the device is four bytes integer – a number of received records.
Note, that the GPRS session should remain active between device and server, while GPRS commands are sent. For this reason, active datalink timeout (global parameters in device configuration) is recommended to be set to 259200 (maximum value).

• General Codec12 message structure

The following diagram shows basic structure of Codec12 messages.

Command message structure:

0x00000000 (Preamble)	Data Size	Codec ID	Command Quantity 1	Type (0x05)	Command Size	Command	Command Quantity 2	CRC-16
4 bytes	4 bytes	1 byte	1 byte	1 byte	4 bytes	X bytes	1 byte	4 bytes

Response message structure:

0x00000000 (Preamble)	Data Size	Codec ID	Response Quantity 1	Type (0x06)	Response Size	Response	Response Quantity 2	CRC-16
4 bytes	4 bytes	1 byte	1 byte	1 byte	4 bytes	X bytes	1 byte	4 bytes

Preamble - the packet starts with four zero bytes.
Data Size - size is calculated from the Codec ID field to the second command or response quantity field.
Codec ID - in Codec12 it is always 0x0C.
Command/Response Quantity 1 - it is ignored when parsing the message.
Type - it can be 0x05 to denote command or 0x06 to denote response.
Command/Response Size – command or response length.
Command/Response – command or response in HEX.
Command/Response Quantity 2 - a byte which defines how many records (commands or responses) are in the packet. This byte will not be parsed but it’s recommended that it should contain the same value as Command/Response Quantity 1.
CRC-16 – calculated from Codec ID to the Command Quantity 2. CRC (Cyclic Redundancy Check) is an error-detecting code using for detect accidental changes to RAW data. For calculation we are using CRC-16/IBM.

Note that difference between commands and responses is message type field: 0x05 means command and 0x06 means response.

• Command coding table

Command has to be converted from ASCII characters (char) to hexadecimal (HEX):

• Command parsing example

Hexadecimal stream of command and answer in this example is given in hexadecimal form. The different fields of the message are separated into different table columns for better readability and understanding.

• GPRS commands examples

Hexadecimal stream of GPRS command and answer in these examples are given in hexadecimal form. The different fields of messages are separate into different table columns for better readability and some of them are converted to ASCII values for better understanding.

1'st example: Sending getinfo SMS command via GPRS Codec12

Server request in hexadecimal stream:
000000000000000F0C010500000007676574696E666F0100004312

Parsed:

Server Command
Server Command Part	HEX Code Part
Zero Bytes	00 00 00 00
Data Size	00 00 00 0F
Codec ID	0C
Command Quantity 1	01
Command Type	05
Command Size	00 00 00 07
Command	67 65 74 69 6E 66 6F
Command Quantity 2	01
CRC-16	00 00 43 12

Note that Server Command converted from HEX to ASCII means getinfo

Device response in hexadecimal stream:
00000000000000900C010600000088494E493A323031392F372F323220373A3232205254433A323031392F372F323220373A3533205253543A32204552523A 312053523A302042523A302043463A302046473A3020464C3A302054553A302F302055543A3020534D533A30204E4F4750533A303A3330204750533A312053 41543A302052533A332052463A36352053463A31204D443A30010000C78F

Parsed:

Device Answer
Device Answer Part	HEX Code Part
Zero Bytes	00 00 00 00
Data Size	00 00 00 90
Codec ID	0C
Response Quantity 1	01
Response Type	06
Response Size	00 00 00 88
Response	49 4E 49 3A 32 30 31 39 2F 37 2F 32 32 20 37 3A 32 32 20 52 54 43 3A 32 30 31 39 2F 37 2F 32 32 20 37 3A 35 33 20 52 53 54 3A 32 20 45 52 52 3A 31 20 53 52 3A 30 20 42 52 3A 30 20 43 46 3A 30 20 46 47 3A 30 20 46 4C 3A 30 20 54 55 3A 30 2F 30 20 55 54 3A 30 20 53 4D 53 3A 30 20 4E 4F 47 50 53 3A 30 3A 33 30 20 47 50 53 3A 31 20 53 41 54 3A 30 20 52 53 3A 33 20 52 46 3A 36 35 20 53 46 3A 31 20 4D 44 3A 30
Response Quantity 2	01
CRC-16	00 00 C7 8F

Note that Device Response converted from HEX to ASCII means:
INI:2019/7/22 7:22 RTC:2019/7/22 7:53 RST:2 ERR:1 SR:0 BR:0 CF:0 FG:0 FL:0 TU:0/0 UT:0 SMS:0 NOGPS:0:30 GPS:1 SAT:0 RS:3 RF:65 SF:1 MD:0

2'nd example: Sending getio SMS command via GPRS Codec12

Server request in hexadecimal stream:
000000000000000D0C010500000005676574696F01000000CB

Parsed:

Server Command
Server Command Part	HEX Code Part
Zero Bytes	00 00 00 00
Data Size	00 00 00 0D
Codec ID	0C
Command Quantity 1	01
Command Type	05
Command Size	00 00 00 05
Command	67 65 74 69 6F
Command Quantity 2	01
CRC-16	00 00 00 CB

Note that Server Command converted from HEX to ASCII means getio

Device response in hexadecimal stream:
00000000000000370C01060000002F4449313A31204449323A30204449333A302041494E313A302041494E323A313639323420444F313A3020444F323A3101000066E3

Parsed:

Device Answer
Device Answer Part	HEX Code Part
Zero Bytes	00 00 00 00
Data Size	00 00 00 37
Codec ID	0C
Response Quantity 1	01
Response Type	06
Response Size	00 00 00 2F
Response	44 49 31 3A 31 20 44 49 32 3A 30 20 44 49 33 3A 30 20 41 49 4E 31 3A 30 20 41 49 4E 32 3A 31 36 39 32 34 20 44 4F 31 3A 30 20 44 4F 32 3A 31
Response Quantity 2	01
CRC-16	00 00 66 E3

Note that Device Response converted from HEX to ASCII means:
DI1:1 DI2:0 DI3:0 AIN1:0 AIN2:16924 DO1:0 DO2:1

• Communication with server

The GSM/GPRS commands can be sent from a terminal program. We recommend to use Hercules (in TCP server mode). Simply write command into Hercules Send field, check HEX box and click Send button. Note that the TCP server must be listening on a specified port (see Port field and Listen button below).

• FMXX and Codec12 functionality
• Garmin

All information is provided in the “FMXX and Garmin development.pdf” document.

• COM TCP Link Mode

All information is provided in the “FMxx TCP Link mode test instructions.pdf” document.

Codec 13

• About Codec13

Codec13 is the original Teltonika protocol for device-server communication over GPRS messages and it is based on Codec12 protocol. The main differences of Codec13 are that timestamp is using in messages and communication is one way only (Codec13 is used for Device -> Server sending).

• General Codec13 message structure

The following diagram shows basic structure of Codec 13 messages:

0x00000000 (Preamble)	Data Size	Codec ID	Command Quantity 1	Type	Command Size	Timestamp	Command	Command Quantity 2	CRC-16
4 bytes	4 bytes	1 byte	1 byte	1 byte	4 bytes	4 bytes	X bytes	1 byte	4 bytes

Preamble – the packet starts with preamble field (four zero bytes).
Data Size – size is calculated from the Codec ID field to the second Command Quantity field.
Codec ID – in Codec13 it is always 0x0D.
Command Quantity 1 – 0x01, it is ignored when parsing the message.
Command Type – it is always 0x06 since the packet is direction is FM->Server.
Command Size – command size field includes size of timestamp too, so it is equal to the size of payload + size of timestamp.
Timestamp – a difference, in milliseconds, between the current time and midnight, January, 1970 UTC (UNIX time).
Command – actual received data.
Command Quantity 2 – a byte which defines how many records (commands) are in the packet. This byte will not be parsed but it’s recommended that it should contain the same value as Command/Response Quantity 1.
CRC-16 – calculated from Codec ID to the Second Number of Data. CRC (Cyclic Redundancy Check) is an error-detecting code using for detect accidental changes to RAW data. For calculation we are using CRC-16/IBM.

Note: Codec13 packets are used only when “Message Timestamp” parameter in RS232 settings is enabled.

• Command parsing example

Hexadecimal stream of GPRS command in this example is given in hexadecimal form. The different fields of message are separate into different table columns for better readability and some of them are converted to ASCII values for better understanding.

Sending getinfo SMS command via GPRS Codec13.

Hexadecimal stream:
00000000000000170D01050000000F0000016C0A81C320676574696E666F0100006855

Parsed:

Server Command
Server Command Part	HEX Code Part
Zero Bytes	00 00 00 00
Data Size	00 00 00 17
Codec ID	0D
Command Quantity 1	01
Command Type	06
Command Size	00 00 00 0F
Timestamp	00 00 01 6C 0A 81 C3 20
Command	67 65 74 69 6E 66 6F
Command Quantity 2	01
CRC-16	00 00 68 55

Note that Server Command converted from HEX to ASCII means getinfo

Codec 14

• About Codec14

Codec14 is the original Teltonika protocol for device-server communication over GPRS messages and it is based on Codec12 protocol.
The main difference of Codec14 is that device will answer to GPRS command if the device physical IMEI number matches specified IMEI number in GPRS command.

Codec14 GPRS commands can be used for sending configuration, debug, digital outputs control commands, or other (special purpose command on special firmware versions).

• FMB firmware requirements

Implemented in base firmware from FMB.Ver.03.25.04.Rev.00 and newer.

• General Codec14 message structure

The following diagram shows the basic structure of Codec14 messages.

Command message structure

0x00000000 (preamble)	Data size	0x0E (Codec ID)	Command quantity	0x05 (Message type)	Command size + IMEI size (8 bytes)	IMEI (HEX)	Command	Command quantity	CRC-16
4 bytes	4 bytes	1 bytes	1 bytes	1 bytes	4 bytes	8 bytes	X bytes	1 bytes	4 bytes

Response message structure

0x00000000 (preamble)	Data size	0x0E (Codec ID)	Response quantity	0x06 / 0x11 (Message type)	Response size + IMEI size (8 bytes)	IMEI (HEX)	Response	Response quantity	CRC-16
4 bytes	4 bytes	1 bytes	1 bytes	1 bytes	4 bytes	8 bytes	X bytes	1 bytes	4 bytes

Preamble – the packet starts with four zero bytes.
Data Size – size is calculated from the Codec ID field to the second command or response quantity field.
Codec ID – in Codec14 it is always 0x0E.
Command/Response Quantity 1 – it is ignored when parsing the message.
Type – if it is request command from server it has to contain 0x05. The response type field will contain 0x06 if it’s ACK or 0x11 if it’s nACK.
Explanation: If command message IMEI is equal to actual device IMEI, received command will be executed and response will be sent with ACK (0x06) message type field value. If command message IMEI doesn’t match actual device IMEI, received command won’t be executed and response to the server will be sent with nACK (0x11) message type field value.
Command/Response Size – command or response length.
Note: make sure that size is IMEI size 8 + actual command size. Minimal value is 8 because Codec14 always contains IMEI and it’s 8 bytes.
IMEI (HEX) – it is send as HEX value. Example if device IMEI is 123456789123456 then IMEI data field will contain 0x0123456789123456 value.
Command/Response – command or response in HEX.
Command/Response Quantity 2 - a byte which defines how many records (commands or responses) are in the packet. This byte will not be parsed but it’s recommended that it should contain the same value as Command/Response Quantity 1.
CRC-16 – calculated from Codec ID to the Second Number of Data. CRC (Cyclic Redundancy Check) is an error-detecting code using to detect accidental changes to RAW data. For calculation we are using CRC-16/IBM.

• GPRS in Codec14 examples

Hexadecimal stream of GPRS command and answer in this example are given in hexadecimal form. The different fields of message are separate into different table columns for better readability and some of them are converted to ASCII values for better understanding.

Sending getver SMS command via GPRS Codec14:

Server requests in Hexadecimal stream:
00000000000000160E01050000000E0352093081452251676574766572010000D2C1

Parsed:

Server Command
Server Command Part	HEX Code Part
Zero Bytes	00 00 00 00
Data Size	00 00 00 16
Codec ID	0E
Command Quantity 1	01
Command Type	05
Command Size	00 00 00 0E
IMEI	03 52 09 30 81 45 22 51
Command	67 65 74 76 65 72
Command Quantity 2	01
CRC-16	00 00 D2 C1

Note that Server Command converted from HEX to ASCII means getver

Device ACK response in hexadecimal stream:
00000000000000AB0E0106000000A303520930814522515665723A30332E31382E31345F3034204750533A41584E5F352E31305F333333332048773A464D42313230 204D6F643A313520494D45493A33353230393330383134353232353120496E69743A323031382D31312D323220373A313320557074696D653A3137323334204D4143 3A363042444430303136323631205350433A312830292041584C3A30204F42443A3020424C3A312E362042543A340100007AAE

Parsed:

Device Answer
Device Answer Part	HEX Code Part
Zero Bytes	00 00 00 00
Data Size	00 00 00 37
Codec ID	0E
Response Quantity 1	01
Response Type	06
Response Size	00 00 00 A3
IMEI	03 52 09 30 81 45 22 51
Response	56 65 72 3A 30 33 2E 31 38 2E 31 34 5F 30 34 20 47 50 53 3A 41 58 4E 5F 35 2E 31 30 5F 33 33 33 33 20 48 77 3A 46 4D 42 31 32 30 20 4D 6F 64 3A 31 35 20 49 4D 45 49 3A 33 35 32 30 39 33 30 38 31 34 35 32 32 35 31 20 49 6E 69 74 3A 32 30 31 38 2D 31 31 2D 32 32 20 37 3A 31 33 20 55 70 74 69 6D 65 3A 31 37 32 33 34 20 4D 41 43 3A 36 30 42 44 44 30 30 31 36 32 36 31 20 53 50 43 3A 31 28 30 29 20 41 58 4C 3A 30 20 4F 42 44 3A 30 20 42 4C 3A 31 2E 36 20 42 54 3A 34
Response Quantity 2	01
CRC-16	00 00 7A AE

Note that Device Response converted from HEX to ASCII means:
Ver:03.18.14_04 GPS:AXN_5.10_3333 Hw:FMB120 Mod:15 IMEI:352093081452251 Init:2018-11-22 7:13 Uptime:17234 MAC:60BDD0016261 SPC:1(0) AXL:0 OBD:0 BL:1.6 BT:4

Device nACK response in hexadecimal stream:
00000000000000100E011100000008035209308145246801000032AC

Parsed:

Device Answer
Device Answer Part	HEX Code Part
Zero Bytes	00 00 00 00
Data Size	00 00 00 10
Codec ID	0E
Response Quantity 1	01
Response Type	11
Response Size	00 00 00 08
IMEI	03 52 09 30 81 45 24 68
Response Quantity 2	01
CRC-16	00 00 32 AC

Differences between Codec 12, Codec 13 and Codec 14

In the table below you will see differences between Codec12, Codec13 and Codec14.

	Codec12	Codec13	Codec14
Communication	Server - Device Communication	One-way (Device -> Server communication)	Server - Device Communication
Codec ID	0x0C	0x0D	0x0E
Response Message Type	0x06	-	0x06 (if it is ACK) or 0x11 (if it is nACK)
Command / Response size	Only Command/Response	Only Command	Command/Response + IMEI
Timestamp	Not Using	Is Using	Not Using
IMEI	Not Using	Not Using	Is Using

24 Position SMS Data Protocol

24-hour SMS is usually sent once every day and contains GPS data for the last 24 hours. TP-DCS field of this SMS should indicate that message contains 8-bit data (i.e. TP-DCS can be 0x04).
Note, that 24 position data protocol is used only with subscribed SMS. Event SMS uses standard AVL data protocol.

• Encoding

To be able to compress 24 GPS data entries into one SMS (140 octets), the data is encoded extensively using bit fields. Data packet can be interpreted as a bitstream, where all bits are numbered as follows:

Byte 1	Byte 2	Byte 3	Byte 4 ...
Bits 0 - 7	Bits 8 - 15	Bits 16 - 24	Bits 25 - ...

Bits in a byte are numbered starting from the least significant bit. A field of 25 bits would consist of bits 0 to 24 where 0 is the least significant bit and bit 24 – most significant bit.

• Structure

Below in the tables you will see SMS Data Structure:

SMS Data Structure
8	Codec ID	Codec ID = 4 (0x04)
35	Timestamp	Time corresponding to the first (oldest) GPS data element, represented in seconds elapsed from 2000.01.01 00:00 EET.
5	ElementCount	Number of GPS data elements

SMS Data Structure
ElementCount *		GPSDataElement	GPS data elements
		Byte - align padding	Padding bits to align to 8 - bits boundary represented in seconds elapsed from 2000.01.01 00:00 EET.
	64	IMEI	IMEI of sending device as 8 byte long integer

The time of only the first GPS data element is specified in Timestamp field. Time corresponding to each further element can be computed as elementTime = Timestamp + (1 hour * elementNumber).

GPS Data Element
		Size (bits)	Field	Description
		1	ValidElement	ValidElement = 1 – there is a valid Gps Data Element following, ValidElement = 0 – no element at this position
ValidElement == 1		1	DifferentialCoords	Format of following data
	DifferentialCoords == 1	14	LongitudeDiff	Difference from previous element‘s longitude. LongitudeDiff = prevLongitude – Longitude + 213 – 1
		14	LatitudeDiff	Difference from previous element‘s latitude LatitudeDiff = prevLatitude – Latitude + 213 – 1
	DifferentialCoords == 0	21	Longitude	Longitude = {(LongDegMult + 18 * 108) * (221 – 1)} over {36*108}
		20	Latitude	Latitude = (LatDegMult + 9*108) * (220 – 1) over {18*108}
		8	Speed	Speed in km/h

Longitude - longitude field value of GPSDataElement
Latitude - latitude field value of GPSDataElement
LongDegMult - longitude in degrees multiplied by 107 (integer part)
LatDegMult - latitude in degrees multiplied by 107 (integer part)
prevLongitude - longitude field value of previous GPSDataElemen
prevLatitude - latitude field value of previous GPSDataElement

• Decoding GPS position

When decoding GPS data with DifferentialCoords = 1, Latitude and Longitude values can be computed as follows: Longitude = prevLongitude – LongitudeDiff + 213 – 1, Latitude = prevLatitude – LatitudeDiff + 213 – 1.
If there were no previous non-differential positions, differential coordinates should be computed assuming prevLongitude = prevLatitude = 0.
When Longitude and Latitude values are known, longitude and latitude representation in degrees can be computed as follows:

• SMS Events

When Configured to generate SMS event user will get this SMS upon event:
<Year/Month/Day> <Hour:Minute:Second> P:<profile_nr> <SMS Text> Val:<Event Value> Lon:<longitude> Lat:<latitude> Q:<HDOP>

Example:
2016./04/11 12:00:00 P:3 Digital Input 1 Val:1 Lon:51.12258 Lat: 25.7461 Q:0.6

Sending data using SMS

This type data sending is using for FMBXXX devices which can be configured in SMS Data Sending settings.

• Data sending via SMS

AVL data or events can be sent encapsulated in binary SMS. TP-DCS field of these SMS should indicate that message contains 8-bit data (for example: TP-DCS can be 0x04).

SMS data (TP-UD)
AVL data array	IMEI
X bytes	8 bytes

AVL data array – array of encoded AVL data.
IMEI – IMEI of sending module encoded as a big-endian 8-byte long number.

CRC-16

CRC (Cyclic Redundancy Check) is an error-detecting code using to detect accidental changes to RAW data. The algorithm on how to calculate CRC-16 (also known as CRC-16/IBM) you will find below.