OBD Device Debugging

Note: This page is in works!

Solution applies for these devices FMB001 FMC001 FMM001 FMB003 FMC003 FMM003

OBD Data Debugging

Device does not read listed OBD OEM parameters

 If you have a vehicle that is listed in the OBD OEM Supported Vehicle List but OBD OEM is not read - follow the log capturing guide below.

Capturing OBD logs from FMX00X via OEM Reset

1. Update the device to the latest firmware available. Preferably 03.28.03.Rev.97 or newer.
2. Make sure that the FMX00X is connected properly to the OBDII Socket.
3. Check for the Configuration. On certain vehicles VIN number is not read automatically - Usually it is with EVs. For this matter check OBD Feature
4. Start vehicle engine.
5. Send following SMS commands to FMX00X device:
   • If you have set SMS login and password:login pass log2sdfilterset 0;2;3;4;1
   • If SMS login and password are not set leave two spaces before command: aalog2sdfilterset 0;2;3;4;1

     If command log2sdfilterset was sent correctly you should receive SMS Response:Enabled Trace Filters:5

6. After the SMS response message OBD log capturing will be started.
7. OBD Function will not work, if vehicle is turned off or not moving - meaning that you need to test drive it for around 10 minutes.
8. After the test drive, turn off vehicle engine.
9. Download captured log (dump) files.

 You can download logs via Teltonika Configurator or via FOTA WEB.

Download logs via Teltonika Configurator

Please check Status info→Maintenance→Log/Dump and download dump YYYY_MM_DD_HH_MM_SS_FMB1YX_IMEI_Dump.zip.

Download logs via FOTA WEB

Enter FOTA WEB → Press on Devices tab → Select your device and press → Task type → Receive internal log → From Oldest → Count 10 (10 files. Each log size up to 1 MB)→
To start download process at once send following SMS command:

1. • If you have set SMS login and password: login pass web_connect
   • If SMS login and password are not set leave two spaces before command: aaweb_connect

     If command was sent correctly you should receive SMS Response:web_connect resp:OK

     To find downloaded log press on Tasks tab→Find your device by IMEI and Task type Received internal log→Download IMEI_logs_TIMESTAMP.zip as showed below:

     

2. These log (dump) files can be read only with special software. Provide these files to your Teltonika Telematics Sales manager or Teltonika Telematics Support team for further investigation.

Requesting for OBD OEM Support / General Problems

 If you have a vehicle that is not listed in the OBD OEM Supported Vehicle List or you are facing problems with OBD OEM in General - follow the log capturing guide below.

Capturing OBD logs from FMX00X with Filters

1. Update the device to the latest firmware available.
2. Make sure that the FMX00X is connected properly to the OBDII Socket.
3. Start vehicle engine.
4. Send following SMS commands to FMX00X device:
   • If you have set SMS login and password:login pass log2sdfilterset 0;2;3;4;1
   • If SMS login and password are not set leave two spaces before command: aalog2sdfilterset 0;2;3;4;1

     If command log2sdfilterset was sent correctly you should receive SMS Response:Enabled Trace Filters:5

5. After the SMS response message OBD log capturing will be started.
6. OBD Function will not work, if vehicle is turned off or not moving - meaning that you need to test drive it for around 10 minutes.
7. After the test drive, turn off vehicle engine.
8. Download captured log (dump) files.

 You can download logs via Teltonika Configurator or via FOTA WEB.

Download logs via Teltonika Configurator

Please check Status info→Maintenance→Log/Dump and download dump YYYY_MM_DD_HH_MM_SS_FMB1YX_IMEI_Dump.zip.

Download logs via FOTA WEB

Enter FOTA WEB → Press on Devices tab → Select your device and press → Task type → Receive internal log → From Oldest → Count 10 (10 files. Each log size up to 1 MB)→
To start download process at once send following SMS command:

1. • If you have set SMS login and password: login pass web_connect
   • If SMS login and password are not set leave two spaces before command: aaweb_connect

     If command was sent correctly you should receive SMS Response:web_connect resp:OK

     To find downloaded log press on Tasks tab→Find your device by IMEI and Task type Received internal log→Download IMEI_logs_TIMESTAMP.zip as showed below:

     

2. These log (dump) files can be read only with special software. Provide these files to your Teltonika Telematics Sales manager or Teltonika Telematics Support team for further investigation.

Basic OBD OEM Configuration

• You need to make sure that your vehicle is supported with OBD OEM parameters. Compatibility can be checked here: OBD OEM Supported Vehicle List
• Enable Codec 8 Extended Protocol

• Configure Ignition Settings according to your vehicle.

 If the vehicle is equipped with Internal Combustion Engine, it is recommended to keep Ignition Source settings with Power Voltage. Otherwise, if it is an EV/HV, set Ignition Source settings as Accelerometer.

• Check if OBD Feature is Enabled

 For Internal Combustion Engine & HV OBD (Auto) must be Checked. If it is an EV, use Non-OBD compliant and enter VIN Source Manually.

• Now it is necessary to enable OBD OEM parameters according to the vehicle list

750px

 Let's say we have a VW Polo 2016. The list tells that Mileage (AVL ID 389), Fuel Level in Liters (AVL ID 390) and Fuel Level in % (AVL ID 48) is supported.

• Enable the listed parameters

 Enabled Fuel Level in % (AVL ID 48) Parameter.

 Enabled Mileage (AVL ID 389) and Fuel Level in Liters (AVL ID 390) Parameter.

• After enabling the parameters proceed with installation of FMX00X device into the OBDII port.

 Once the device is installed, turn on the Ignition and send SMS command web_connect. This will force the device to acquire OBD OEM File from FOTA WEB.

Verify the Status on FOTA WEB

• Open your FOTA WEB account
• Find device by IMEI

Under Details, OBD section, you should see the VIN Number of your vehicle:	Under Tasks, you can verify if the file is delivered to the device or not:

 Lastly, check your server for the availability of OBD OEM Data.

OBD Feature

OBD Feature for Vehicles with Internal Combustion Engine

 Regular configuration for vehicles with Internal Combustion engines. OBD Feature OBD (Auto), Vin Source (Auto).

 If Auto VIN reading does not work, enter VIN Number manually.

OBD Feature for EVs

 Configuration for EVs. OBD Feature Non-OBD compliant, Vin Source (Manual).

Renault & Peugeot Specific FMB003 Information

 If you have Renault or Peugeot vehicle and OBD OEM does not work, check if you have the latest FMB003 Hardware.

Verify FMB003 Hardware Status on FOTA WEB

• Open your FOTA WEB account
• Find device by IMEI

OLD HARDWARE	NEWER HARDWARE

 With this example FMB003OENJ01 is an old hardware and FMB00377NJ01 being a newer one. If Product Code contains - FMB003OE consider getting a newer Hardware. Contact your Sales Manager for more information.