FMB firmware errata 04.00.00: Difference between revisions

Revision as of 14:23, 8 January 2025

Introduction

We are always improving our devices performance, stability and reliability. That’s why Teltonika is one of the leading GNSS trackers manufacturers in the world.
This document describes FMBXXX, FMCXXX, FMUXXX, FMMXXX platform devices firmware improvements, changes, new features implementations as well as current firmware release version.


FIRMWARE VERSION	SUPPORTED HARDWARE
01.00.XX	FMB0YX, FMB9X0
01.01.XX	FMB0YX, FMB9X0, FMB96X
01.03.XX	FMB0YX, FMB9X0, FMB96X
03.01.XX	FMB0YX, FMB9X0, FMB96X, FMB1YX
03.02.XX	FMB0YX, FMB9X0, FMB96X, FMB1YX
03.06.XX	FMB0YX, FMB9X0, FMB96X, FMB1YX, FM30XY
03.07.XX	FMB0YX, FMB9X0, FMB96X, FMB1YX, FM30XY, FMB2YX
03.18.XX	FMB0YX, FMB9X0, FMB96X, FMB1YX, FM30XY, FMB2YX, FMT100
03.25.XX	FMB0YX, FMB9X0, FMB96X, FMB1YX, FM30XY, FMB2YX, FM30XY, FMT100
03.27.XX	FMB0YX, FMB9X0, FMB96X, FMB1YX, FMU1YX, FMM1YX, FMC1YX, FMM001, FMC001, FM30XY, FMB2YX, FMT100
03.29.XX	FMB010, FMB020, FMT100, FMB900, FMB910, FMB920, FMC920, FMM920, FMB110, FMB120, FMB122, FMB125, FMB130, FMC125, FMC130, FMC13A, FMM125, FMM130, FMM13A, FMB202, FMB204, FMB225, FMB230, FMC225, FMC230, FMM230, FMB001, FMB003, FMC001, FMC003, FMC00A, FMM001, FMM003, FMM00A, FMB140, FMB240
03.29.XX	FMB010, FMB020, FMT100, FMB900, FMB910, FMB920, FMC920, FMM920, FMB110, FMB120, FMB122, FMB125, FMB130, FMC125, FMC130, FMC13A, FMM125, FMM130, FMM13A, FMB202, FMB204, FMB225, FMB230, FMC225, FMC230, FMM230, FMB001, FMB003, FMC001, FMC003, FMC00A, FMM001, FMM003, FMM00A, FMB140, FMB240
04.00.XX	FMB010, FMB020, FMT100, FMC800, FMM800, FMM80A, FMC880, FMM880, FMB900, FMB910, FMB920, FMC920, FMM920, FMB110, FMB120, FMB122, FMB125, FMB130, FMC125, FMC130, FMC13A, FMM125, FMM130, FMM13A, FMB202, FMB204, FMB225, FMB230, FMC225, FMC230, FMM230, FMC234, FMB001, FMB003, FMC001, FMC003, FMC00A, FMM001, FMM003, FMM00A, FMB140, FMB240

Evaluation firmware branches

Newly introduced Teltonika Telematics products start their lifecycle and mass production running evaluation branch firmware versions, which may be based on older BASE firmware version or separate firmware branch, therefore may have different features. Such products do not immediately receive identical improvements as products in BASE firmware until their support is added. Currently such products are:


FIRMWARE VERSION	HARDWARE
03.29.00.Rev.458	FMC880, FMM880, FMC800, FMM800, FMM80A
03.29.00.Rev.157	FMB150, FMC150, FMM150, FMC250, FMM250
03.27.10.Rev.482	FMB930
03.29.00.Rev.931	FMB965
03.29.00.Rev.554	FMP100, FMB020
03.29.00.Rev.601	FMC234
03.29.00.Rev.263	FMB209

Firmware versioning

Structure

FMB(T).VER.[XX].[YY].[ZZ].Rev.[##] _[ID###]

Syntax description
- XX – major FW version.
- YY – branch number, shows major changes in firmware, i.e. new module support added or new major feature added.
- ZZ – major changes like bigger fixes, improvements and new features addition.
- ## – minor changes like small fixes and improvements.
- ID[###] – Spec ID KEY – Specific clients FW changes.

Firmware versions


FIRMWARE VERSION	RELEASE DATE	CHANGES
04.00.00.Rev.01 (recommended for FMT100, FMB900, FMB910, FMB920)	2024.01.17	NEW! Major version updated to 4.0.0 and downgrade protection added NEW! Added support for FMC880, FMM880 NEW! Added support for FMC800, FMM800, FMM80A NEW! Added support for FMC234 HW support NEW! Modem recovery mechanism to address modem hangs resulting from network issues or poor signal conditions NEW! Implemented support for encrypted CAN commands over Bluetooth NEW! Enhanced “Advanced Unplug Detection” with additional condition options for speed and delay NEW! Added Beacon option for “Authorized Read Notification” feature NEW! Added Dynamic Ground vector feature for more accurate accelerometer data NEW! Conditions when device operation is prohibited enabled NEW! Added “Window state” security state flag elements NEW! Enabled devices to send records to a duplicate server via TCP in Codec JSON, while the primary server uses MQTT with TLS encryption NEW! Enabled “Driving state” and “Driving records” I/O elements for FMC880/FMM880 devices NEW! Added a DIN3 option as a trigger for outgoing calls in HF settings NEW! Added "set calibration" command NEW! Added a new GNSS I/O status value '4' - GNSS ON with an active GNSS filter. NEW! “Stay Awake” parameter option added for “Sleep Mode” NEW! “DTC Request on Engine Start” feature to avoid conflicts with external diagnostic equipment NEW! Added support of PCB temperature I/O element for devices with NTC CHANGED! Default logging filters updated CHANGED! Unplug detection events are allowed to be sent before device going to Low Power Mode CHANGED! Adjusted accelerometer sensitivity to be more suitable for crash detection CHANGED! Set GNSS jamming DOUT control to a higher priority over maintenance DOUT CHANGED! Modifications to alibration algorithm for greater accuracy CHANGED! BLE Advertising period to 500ms CHANGED! Refactored the Immobilizer Authorized ID checking feature CHANGED! Incremental retry periods for AGPS EPO download to improve successful download time period CHANGED! Program number parameter ID 11120 size increased and max value to 99999 CHANGED! Additional traces for GPS and GSM jamming status in device log Corrected the byte inversion issue in 1-Wire Matrix (ReadROM) ID parsing Device abnormal working with dynamic bt name when using value of 16 characters with %imei function resolved Addressed issues where the device behaved abnormally after receiving a #FWD DAT command with the target set to Bluetooth and a NULL payload Fine-tuned the parsing for start and end delimiters in RS232 Delimiter mode to enhance functionality Fixed an issue where high priority records were not sent if a call was triggered by a feature activation Resolved an issue where link was not close properly sometimes after sending a record in Low Power Mode Enhanced the retry mechanism for SIM PIN entries if the initial attempt was unsuccessful Adjusted the saving of the Digital Output state post-firmware update when the inverted mode is selected Enabled missing CAN RSF parameters Adjusted the operator ban list logic to have a search timeout of 5 minutes and a ban time of 30 minutes Resolved unexpected wake-ups from sleep due to repeated time-sync issues and server failures to close sockets correctly Patched the fail count algorithm for 1-wire data reading to improve stability Disallowed GSM updates during server response wait periods to prevent duplicate record sending in online deep sleep mode Removed disallowed MCCs (250, 257, 432, 368, 467) from the APN list Improved parsing of VIN and Trailer VIN values Resolved EYE Sensor filtering issue by MAC or Name when configuration parameter “Identifier” was changed Resolved an issue where UL202 record value was incorrectly parsed in device logs Enabled band 26 selection for devices equipped with Quectel BG95-M3 modems Resolved an issue where logging was disabled after a firmware update Enhanced memory management to ensure continuous logging, even when memory is full, by rewriting the oldest files Changed the BLE advanced data offset type to signed to correct inaccuracies when negative offsets were used Updated the DOUT control from the Ignition FSM to prevent feature bypass when switching ignition on and off within 1 second Adjusted the conversion of EYE "Major" and "Minor" values, ensuring data is packed according to Bigger Endian format when "Lost&Found" record are generated Corrected a typographical error in the lvcangetinfo response Resolved an issue where the device was unable to enter sleep mode due to an NTP sync being stuck Fixed an issue where the first GPRS command was ignored after the device connected to a Backup Server Resolved an issue where DTC fault codes were not correctly packed into records for some EV and Hybrid vehicles. Improved SIM switch logic in devices equipped with Quectel modems Removed an unnecessary filter for the instant movement element status Resolved an issue where private/business mode was not functioning according to the weekly schedule Improved device stability when NMEA logging is enabled via RS232 at 9600 baud Enhanced device stability when a 2kHz signal is detected by the device using "Advanced Pulse Counter" feature Resolved an issue where 2G devices could not open a socket for a period after disconnecting from the network due to poor network conditions Resolved an issue where duplicate records were created if UART communication with the modem stopped working while the device was in GNSS/ODS sleep mode and USB was connected Improved the handling of the socket closing for devices with MeiG modules when TLS and Deep Sleep are used Improved the stability of OBD dongle data reading after a Bluetooth module restart Resolved an issue where the device would sometimes fully wake up from Deep Sleep due to periodic record sending Resolved an issue where the "Advanced Pulse Counter" parameter ID 145 would not reset to default settings via configurator Resolved an issue where EYE Beacon flag 27 data voltage and temperature values was not included not into record when "Beacon Simple" mode was usedImproved the accuracy of device tracking location in "Low Power Mode" Resolved an issue where the getinfo response was split into several SMS messages Improved device stability when Private Mode is triggered by Virtual DIN2 Resolved an issue where firmware downloads would interrupt frequent record sending for devices with MeiG modules EYE sensors status are now shown correctly in device logs Resolved an issue where on random cases, a trip end event was received with the trip odometer already reset to 0 Adjusted so that the movement off timeout would not reset after device restart Disabled unnecessary tasks to decrease current consumption in UDS mode Resolved an issue where the WD counter was not functioning as expected in ODS mode Reduced the delay for Immobilizer activation after waking up from sleep Resolved an issue where the GNSS module would not return to operation after being jammed Resolved an issue where the program number could not be changed sometimes with an SMS command Applied a patch to support APDU commands, preventing connectivity issues when the device uses specific SIMs and crosses borders Ensured odometer values are saved after a fix loss to prevent resetting when the device powers off Applied a patch so that timestamps in crash traces are calculated relative to the crash event, preventing trace damage if a time jump occurs during a crash Applied a patch to improve Bluetooth interface stability when detecting a large number of Beacons Resolved an issue where the "On-Demand Tracking", "Activation By" parameter ID 10992 would not reset to default via configurator Resolved an issue where EYE sensor I/O values would be included in the record even if the "Working Mode" parameter was configured as "Disabled" Movement will be accurately detected after the movement detection delay period, and not simultaneously with towing detection when it is activated Resolved an issue where the Immobilizer would not retrigger the Digital output immediately if the ignition was turned on for shorter than 1 second Adjusted the btgetlist 3 command to return a full scanned object list Resolved an issue where the "Odometer Calculation Source" parameter ID 11806 did not reset back to the default value when the configuration was reset Resolved an issue where Beacon info remained visible in the configurator UI even when detection was disabled Resolved an issue where the TTFF (Time to First Fix) result was sometimes reported as 0 even though a fix was acquired Resolved an issue where the Digital Output was not activated by the "Immobilizer" scenario when the "Ignition Off timeout" was set to longer than the "Sleep Timeout" Implemented a minor interface control tweak for 1-wire interface stability Removed unnecessary spam from device log prints Corrected the behavior to stop advertising BLE packets once a connection is established Resolved an issue where the device's 1-Wire interface functioned incorrectly if the 1-Wire in Sleep mode parameter value changed while the device was in sleep mode Resolved an issue where fake movement was detected due to incorrect GNSS speed data acquired from the GNSS module Tweaked the BLE GATTS disconnect process to enable correct disconnection Resolved an issue where devices in Deep Sleep mode would sometimes fail to report the disconnected status using MQTT Resolved an issue where devices with MeiG modules would repeat a call after the first one was rejected
03.29.00.Rev.21 (recommended for FMB122, FMB125, FMM125, FMC125 (SLM320-LA, SLM320-E2, EC21-EC), FMC225, FMC920, FMM920)	2024.08.07	Optimized the startup process of the network modules to improve pass-rate during manufacturing testing. Dual SIM switching enhancements to improve pass-rate during manufacturing testing. Return real SIM slot for factory testing commands.
03.29.00.Rev.19 (recommended for FMC920)	2024.06.05	Fixed FOTA task execution while working in 2G Network mode for devices with Quectel EG915U modules.
03.29.00.Rev.18 (recommended for FMT100, FMB900, FMB910, FMB920, FMC920, FMM920, FMB110, FMB120, FMB122, FMB130, FMC130 (SLM320-LA, SLM320-E2, EC21-EC, EC21-AU), FMC13A, FMM130 (BG95-M3, BG96), FMM13A, FMB202, FMB204, FMB206, FMB230, FMC230, FMM230, FMB140, FMB240, FMB125, FMC125 (SLM320-LA, SLM320-E2, EC21-EC), FMM125 (BG95-M3), FMB225, FMC225)	2024.05.13	Improved reconnection to new operator time if GPRS was unavailable with initial operator Fixed pro-longed reconnection to new operator due to record tasks interrupting operator search Fixed network session closing when current operator is added to blacklist Improved module initialization time for devices with Quectel modems Fixed Digital Output state restore after firmware update RS232 interface stability improvements GNSS status element state improvements Time synchronization improvements Manufacture testing improvements
03.29.00.Rev.13 (recommended for FMC130 with SLM320-LA, SLM320-E1, SLM320-E2, FMC230 with SLM320-LA, SLM320-E2, FMC920)	2023.11.24	NEW! TELTONIKA EYE Beacon and EYE Sensor easy configuration functionalities added NEW! TELTONIKA EYE Beacon Lost & Found and Proximity Event functionalities added NEW! SECO functionality added NEW! Back-Up Tracker functionality added NEW! GNSS jamming functionality added NEW! Low Power Mode functionality added NEW! MQTT support for AWS IoT Shadow/Custom and Azure IoT added NEW! RS485 Buffered functionality added NEW! RS232 Delimiter mode functionality added NEW! 1-Wire interface control in sleep modes functionality added NEW! BT/BLE interface control in sleep modes functionality added NEW! NBL-2 Bluetooth RFID reader support added NEW! SMS/GPRS command "lvcanhorn" support added NEW! Added support for FMC13A and FMM13A NEW! Added support for FMC00A and FMM00A NEW! Added support for FMC920 and FMM920 NEW! Added support for FMC003 and FMM003 NEW! Added support for small OBD devices FMB003 and FMB020 NEW! Added support for FMC1XY/FMC2XY devices with MeiG modems NEW! SMS/GPRS command "setigndigout" added NEW! Jamming feature support added for FMC1XY/FMC2XY devices with MeiG modems NEW! Support of new electric vehicle OEM parameters for FMX00X devices NEW! CAN service and LPG I/O elements added NEW! New I/O elements for each CAN adapter state flag added NEW! New I/O Digital Input 2 for FMX920, FMB910 and FMB900 devices CHANGED! Reworked recalibration logic CHANGED! Default parameter values CHANGED! SMS Event logic reworked CHANGED! LLS address count expanded to 16 CHANGED! Black list functionality reworked CHANGED! SMS/GPRS command "cpureset" protection functionality CHANGED! Pulse Counter reworked 1-Wire Temperature sensor stability improvements Operator search procedure functionality improvements Record saving and sending improvements DOUT state saving improvements GPRS Session and PDP Context Activation logic improvements Trip state saving improvements CAN data reading improvements BLE data reading stability improvements TimeSync, SMS handling and connection stability improvements for FMC1XY/FMC2XY devices with MeiG modems AutoAPN multiple block file improvement for larger database capacity Manufacture testing improvements Improved system stability and fixed general bugs
03.28.02.Rev.197 (recommended for FMC920, FMM920)	2023.05.12	AutoAPN logic improvements Records sending improvements for eSIM hardware versions Optimized network communication to ensure stable connection Improved system stability and fixed general bugs Manufacture testing improvements
03.28.02.Rev.195 (recommended for FMC920)	2022.11.28	Jamming detection support added for new Quectel EG915U FW (EU and LA versions) Additional security to ensure communication with Quectel module added
03.28.02.Rev.87 (recommended for FMC920)	2022.07.28	Fix for SIM pin enter
03.28.02.Rev.85 (recommended for FMC920, FMM920)	2022.07.13	Initial release

@@ Line 104: / Line 104: @@
 ! style="width: 60%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: left;" |CHANGES
 |-
-|style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |<span class="mw-headline" id="04.00.00.Rev.01">{{{fw|'''04.00.00.Rev.01'''}}}</span><br /> (recommended for FMT100, FMB900, FMB910, FMB920)
+|style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: top; background: white;" |<span class="mw-headline" id="04.00.00.Rev.01">{{{fw|'''04.00.00.Rev.01'''}}}</span><br /> (recommended for FMT100, FMB900, FMB910, FMB920)
-| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |{{{release_date| 2024.01.17}}}
+| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: top; background: white;" |{{{release_date| 2024.01.17}}}
 | style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: top; background: white;" |
 * '''NEW!''' Major version updated to 4.0.0 and downgrade protection added