Conditions when device operation is prohibited

Introduction

From evaluation firmware version 03.27.16.Rev.XX and also from 04.00.00.Rev.XX base firmware version conditions are enabled to prevent device from operating when it is being used in restricted countries. Block diagram of the logic is presented in figure 1:

Block diagram of logic (figure 1)

Description

Device Blocking

Device will automatically stop operating when conditions will be met. Conditions are hardcoded and cannot be changed:

1. Device connects to operator with restricted Mobile Country Code (MCC) and restriction timestamp is reached.
2. Restricted operator list contains MCCs:

  250 - Russian Federation
  257 - Belarus
  432 - Iran
  368 - Cuba
  467 - North Korea

28-Day Blocking Counter:

• When a device connects to a restricted MCC (Mobile Country Code) it saves blocking timestamp (current timestamp + 28 days) and starts counter as depicted in figure 1 flowchart. The counter tracks the cumulative number of days the device spends connected to restricted operators.
• If the device reaches 28 cumulative days of connection to restricted MCCs, it will be automatically blocked.

Resetting the Counter:

• To reset the counter and timestamp, the device must connect to a non-restricted MCC continuously for 7 uninterrupted days.
• If the device disconnects or connects to a restricted MCC during this 7-day reset period, the reset process fails, and the 28-day counter continues accumulating.

Example 1:

• The device spends 10 days connected to a restricted MCC.
• It then disconnects for 5 days to allowed operator.
• Upon reconnecting to the restricted MCC, the blocking counter resumes from 15 days (as the 7-day reset period was not met).
• If the device remains connected to restricted MCC for an additional 13 days, the counter reaches 28 days, and the device will be blocked.

Example 2:

• The device spends 15 days connected to a restricted MCC.
• It then connects to a non-restricted MCC continuously for 7 uninterrupted days.
• In this case, the counter is fully reset to 0 days, and after device reconnects to a restricted MCC counter will starts from day 0.

Device Unblocking

To unblock the device, as depicted in figure 1 flowchart, the device must maintain a continuous connection to operators with non-restricted MCCs for a full 7 days. Additionally, the device must have an active time synchronization and an inserted SIM card. If the device connects to a restricted operator MCC during this period, the unblocking counter resets.

Operating Device in Blocked State

Blocked Features	Description
Record saving	Device will stop saving periodic and eventual records. Prior to device blocking saved records will not be lost.
Record sending	Device will not send any records to server. Prior saved records will be stored and sent once device is unblocked.
Periodic scenario update	Various features will be stopped: OBD/LVCAN Output/Input controlling/reading Geofencing Trip Ecodriving GSM Jamming GSM Jamming GNSS Jamming Fuel Consumption Immobilizer Overspeeding Private/Business Ignition update Sleep
Sleep (Power Update)	Sleep feature will be disabled as well as Charger update, OBD plug out notify and OBD unlocker. Since these tasks runs under Power Update task which is responsible for sleep.
Accelerometer	Accelerometer reading will be stopped and accelerometer should not be initialized
IO element updating	IO element values will not be updated
Accelerometer related scenarios	Movement detection, crash detection etc.
BLE Sensors updating	Updating of BLE sensors will be stopped

Firmware Upgrade/Downgrade Rules

Firmwares have specific restrictions:

Firmware release 03.27.16

• When a device is updated to 03.27.16.Rev.00 or a newer revision:

1. Downgrade to a version below 03.27.16.Rev.00 is not allowed
2. Upgrades to newer revisions of 03.27.16 is allowed
3. Upgrades to other firmware other than 03.27.16.Rev.XX and 04.00.00.Rev.XX is not allowed
Note:

• Upgrading from 03.27.16 to 04.00.00 can only be done using the specific intermediate version: 03.27.16.Rev.02

Firmware release 04.00.00

• When a device is updated to 04.00.00.Rev.00 or a newer revision:

1. Downgrade to a version below 04.00.00.Rev.00 is not allowed
2. Upgrades to newer versions than 04.00.00.Rev.00 is allowed

Pass through command

In order to allow client to know the location of the vehicle in special cases, pass through for single command has been implemented. SMS/GPRS command “getgps” will be allowed to be sent every 10 minutes to get location of the device, when it is operating in Blocked state.