Jump to content
  • EN

Template:FTX First Start: Difference between revisions

From Teltonika Telematics Wiki
Newer edit →
VisualWikitext
Created page with "<b> {{#switch: {{{model|FTC881}}} | FTC881 = Small and smart waterproof tracker | FTC921 = Small and smart tracker | FTC961 = Small and smart waterproof tracker | FTC305 = Small tracker for e-bikes, e-scooters and e-forklifts with CAN interface, high gain GNSS/GSM antennas, Bluetooth® wireless technology, high capacity internal Li-ion battery and 10-97 V power supply range | #default = Small and smart tracker }} </b> [[Image:{{{model|}}}-datasheet.png|400px|right]] <b..."
 
No edit summary
Line 15: Line 15:
=='''KNOW YOUR DEVICE'''==
=='''KNOW YOUR DEVICE'''==
[[File:{{{model|}}} KNOW YOUR DEVICE.PNG|centre|1000 px]]
[[File:{{{model|}}} KNOW YOUR DEVICE.PNG|centre|1000 px]]
{{#switch: {{{model|FTC881}}}
| FTC881
| FTC961 =
=='''HOW TO REMOVE COVER'''==
{|
|-
| [[File:Alert.png|left|link=]] || <b> Device casing is designed to be water-proof and match requirements for IP69K. Please note that once the cover is fully clipped it will require additional plastic pry tools to be opened! Please make sure to review short walkthrough video for more details:</b>
|}
<youtube>https://www.youtube.com/watch?v=fgOQtk6X0nw</youtube>
}}


=='''SET UP YOUR DEVICE'''==
=='''SET UP YOUR DEVICE'''==
{|
|-
| [[File:Alert.png|left|link=]] || <b> Physical SIM card insertion/removal must be performed when device is powered off – external voltage {{{battery|and internal battery}}} disconnected. Otherwise, the SIM card might be damaged or device will not detect it.</b>
|}


{{#switch: {{{model|FTC881}}}
{{#switch: {{{model|FTC881}}}
Line 64: Line 85:


{{{SETUP1|[[Image:FTX305_non-casing_setup.png|850px]]}}}
{{{SETUP1|[[Image:FTX305_non-casing_setup.png|850px]]}}}
}}
{|
|-
| [[File:Alert.png|left|link=]] || <b>{{{sim_type|Nano-}}}SIM card insertion/removal must be performed when device is powered off – external voltage {{{battery|and internal battery}}} disconnected. Otherwise {{{sim_type|Nano-}}}SIM card might be damaged or device will not detect it.</b>
|}
=='''HOW TO REMOVE COVER'''==
{{#switch: {{{model|FTC881}}}
| FTC881
| FTC961 =
{|
|-
| [[File:Alert.png|left|link=]] || <b> Device casing is designed to be water-proof and match requirements for IP69K. Please note that once the cover is fully clipped it will require additional plastic pry tools to be opened! Please make sure to review short walkthrough video for more details:</b>
|}
<youtube>https://www.youtube.com/watch?v=fgOQtk6X0nw</youtube>


}}
}}
Line 104: Line 106:


}}
}}
=='''HOW TO INSTALL USB DRIVERS (WINDOWS)'''==
# Please download COM port drivers from '''[[Media:TeltonikaCOMDriver.zip|here]]'''.
# Extract and run '''TeltonikaCOMDriver.exe'''.
# Click '''Next''' in driver installation window.
# In the following window click '''Install''' button.
# Setup will continue installing the driver and eventually the confirmation window will appear. Click '''Finish''' to complete the setup.
=='''CONFIGURATION (WINDOWS)'''==
At first, {{{model}}} device will have default factory settings set. These settings should be changed according to the user's needs. Main
configuration can be performed via [https://wiki.teltonika-gps.com/view/Telematics_Configuration_Tool_(TCT) Teltonika Configurator tool (TCT)].


=='''LED BEHAVIOUR DESCRIPTION'''==
=='''LED BEHAVIOUR DESCRIPTION'''==


This section is an explanation of LED indications on an {{{model}}} device.
This section is an explanation of LED indications on {{{model}}} device.
<br>
<br>


Line 168: Line 183:


}}
}}
=='''HOW TO INSTALL USB DRIVERS (WINDOWS)'''==
# Please download COM port drivers from '''[[Media:TeltonikaCOMDriver.zip|here]]'''.
# Extract and run '''TeltonikaCOMDriver.exe'''.
# Click '''Next''' in driver installation window.
# In the following window click '''Install''' button.
# Setup will continue installing the driver and eventually the confirmation window will appear. Click '''Finish''' to complete the setup.
=='''CONFIGURATION (WINDOWS)'''==
At first {{{model}}} device will have default factory settings set. These settings should be changed according to the user's needs. Main
configuration can be performed via [https://wiki.teltonika-gps.com/view/Telematics_Configuration_Tool_(TCT) Teltonika Configurator tool (TCT)].


=='''PINOUT'''==
=='''PINOUT'''==
Line 344: Line 346:
* Ground wire must be connected to the vehicle frame or metal parts that are fixed to the frame.
* Ground wire must be connected to the vehicle frame or metal parts that are fixed to the frame.
* If the wire is fixed with the bolt, the loop must be connected to the end of the wire.
* If the wire is fixed with the bolt, the loop must be connected to the end of the wire.
* For better contact scrub paint from the spot where loop is going to be onnected.
* For better contact scrub paint from the spot where loop is going to be connected.


}}
}}


[[Category:{{{model}}}]]
[[Category:{{{model}}}]]

Revision as of 15:52, 17 February 2025

Small and smart waterproof tracker

File:-datasheet.png


KNOW YOUR DEVICE

File:KNOW YOUR DEVICE.PNG


HOW TO REMOVE COVER

{

SET UP YOUR DEVICE

 Physical SIM card insertion/removal must be performed when device is powered off – external voltage and internal battery disconnected. Otherwise, the SIM card might be damaged or device will not detect it.
  1. Device is delivered partly closed. Gently remove FTC881 cover.
  2. Insert Nano-SIM card as shown. Make sure that Nano-SIM card cut-off corner is pointing towards SIM slot.
  3. Battery is already connected, so after configuring device fully close casing.
  4. Device is ready to be mounted.

PC CONNECTION (WINDOWS)

  1. Power-up {{{model}}} with DC voltage (10-90V) power supply using power wires. LEDs should start blinking, see "LED BEHAVIOUR DESCRIPTION".
  1. Connect device to computer using USB Type-C cable and install USB driver, see "HOW TO INSTALL USB DRIVERS (WINDOWS)".

HOW TO INSTALL USB DRIVERS (WINDOWS)

  1. Please download COM port drivers from here.
  2. Extract and run TeltonikaCOMDriver.exe.
  3. Click Next in driver installation window.
  4. In the following window click Install button.
  5. Setup will continue installing the driver and eventually the confirmation window will appear. Click Finish to complete the setup.

CONFIGURATION (WINDOWS)

At first, {{{model}}} device will have default factory settings set. These settings should be changed according to the user's needs. Main configuration can be performed via Teltonika Configurator tool (TCT).

LED BEHAVIOUR DESCRIPTION

This section is an explanation of LED indications on {{{model}}} device.

NAVIGATION LED INDICATIONS

Behaviour Meaning
Permanently switched on GNSS signal is not received
Blinking every second Normal mode, GNSS is working
Off GNSS is turned off because:
Device is not working
or
Device is in sleep mode
Blinking fast constantly Device firmware is being flashed


STATUS LED INDICATIONS

Behaviour Meaning
Blinking every second Normal mode
Blinking every two seconds Sleep mode
Blinking fast for a short time Modem activity
Off Device is not working
or
Device is in boot mode

PINOUT

{

MOUNTING RECOMMENDATIONS

DEVICE FASTENING

  • Locate the battery in your vehicle. If present remove the battery cover to access the battery.
  • There is a double sided tape on the back of the device, use it to attach the device on the battery, so that the GNSS antenna and LEDs indicators are facing up.

CONNECTING POWER SOURCE

  • Device power wire is designed to be directly connected to the positive terminal fastener of the vehicle battery.

CONNECTING GROUND WIRE

  • Device ground wire is designed to be directly connected to the negative terminal fastener of the vehicle battery.

[[Category:{{{model}}}]]

Retrieved from "https://wiki.teltonika-gps.com/index.php?title=Template:FTX_First_Start&oldid=102272"