Difference between revisions of "Template:FMB630 System Settings"

From Wiki Knowledge Base | Teltonika GPS
(Created page with "System settings have 7 configurable parameters: *Sleep settings, where user can turn GPS sleep/deep sleep on or off; *Analog Input Settings, where user can choose analog input...")
 
Line 1: Line 1:
System settings have 7 configurable parameters:
+
System settings have 5 configurable parameters:
*Sleep settings, where user can turn GPS sleep/deep sleep on or off;
+
*Sleep mode - where user can turn GPS sleep/deep sleep on or off;
*Analog Input Settings, where user can choose analog input range 10 V or 30 V, depending on needed accuracy (lower range gives higher accuracy of measurements), and input voltage;
+
*Sleep timeout - timer which starts after every sleep condition is met and will end up with device going to sleep mode;
*Object Motion Detection Settings, where user can configure 3 ways how {{{model|FMB630}}} will detect stopped movement, and change its working mode;
 
*Static navigation settings, where user can turn static navigation on or off;
 
*Records Settings, where user can enable or disable records when GPS is not available (no time synchronization);
 
*GNSS Settings, where user can choose satellite system and GNSS FIX Timeout Time (if after timeout there will not be synchronized time, it will be synchronized via NTP server);
 
 
*Ignition Source sets ignition triggered functionalities to be triggered by:
 
*Ignition Source sets ignition triggered functionalities to be triggered by:
 
**Power Voltage (if voltage is between High Voltage Level and Low Voltage Level the ignition is considered to be turned on);
 
**Power Voltage (if voltage is between High Voltage Level and Low Voltage Level the ignition is considered to be turned on);
**Digital Input (DIN1 ON – ignition on, DIN1 OFF – ignition off);
+
**Digital Input 1;
 +
**Digital Input 2;
 +
**Digital Input 3;
 +
**Digital Input 4;
 
**Movement (if accelerometer/movement sensor detects movement then ignition is on, if movement stops – ignition is off).
 
**Movement (if accelerometer/movement sensor detects movement then ignition is on, if movement stops – ignition is off).
  

Revision as of 14:37, 31 May 2018

System settings have 5 configurable parameters:

  • Sleep mode - where user can turn GPS sleep/deep sleep on or off;
  • Sleep timeout - timer which starts after every sleep condition is met and will end up with device going to sleep mode;
  • Ignition Source sets ignition triggered functionalities to be triggered by:
    • Power Voltage (if voltage is between High Voltage Level and Low Voltage Level the ignition is considered to be turned on);
    • Digital Input 1;
    • Digital Input 2;
    • Digital Input 3;
    • Digital Input 4;
    • Movement (if accelerometer/movement sensor detects movement then ignition is on, if movement stops – ignition is off).


Stop Detection Source Vehicle on Stop mode Vehicle Moving mode
Ignition (recommended) If ignition (configured Ignition Source) is logic low If ignition (configured Ignition Source) is logic high
Msensor (movement sensor) Internal movement sensor does not detect movement Internal movement sensor detects movement
GPS GNSS fix is available and vehicle speed is lower than 5 km/h GNSS fix is available and vehicle speed is higher than 5 km/h
While GNSS fix is unavailable, Object Motion Detection Settings are working like in Msensor mode


Static Navigation Mode is a filter, which filters out track jumps when the object is stationary. If Static navigation filter is disabled, it will apply no changes on GNSS data. If Static navigation filter is enabled, it will filter changes in GNSS position if no movement is detected (depends on Object Motion Detection Settings). It allows filtering GNSS jumps when object is parked (is not moving) and GNSS position is still traced.


FM36 Sys Settings.jpg


Also if Power Voltage is chosen for ignition source there is possibility to choose Manual ignition detection or automatic ignition detection. For manual ignition user has to choose power voltage levels by himself. For automatic ignition FMB630 automatically detects ignition, ignition is on if power voltage is between 13,2 – 16 V, or 27 – 32 V.