Template:FM36YX I/O settings

When no I/O element is enabled, AVL packet comes with GNSS information only. After enabling I/O element(s) AVL packet along with GNSS information contains current value(s) of enabled I/O element.

Permanent I/O elements (are always sent to server if enabled)
No.	Property Name	Description
00	Digital Input Status 1	Logic: 0 / 1
01	Digital Input Status 2	Logic: 0 / 1
02	Digital Input Status 3	Logic: 0 / 1
03	Digital Input Status 4	Logic: 0 / 1
04	Analog Input 1	Voltage: mV, 0 – 30 V
05	Digital Output 1	Logic: 0 / 1
06	Digital Output 2	Logic: 0 / 1
07	GNSS PDOP	Probability * 10; 0-500
08	GNSS HDOP	Probability * 10; 0-500
09	External Voltage	Voltage: mV, 0 – 30 V
10	GNSS Power	States: 0 – off state (when GPS module is off) 1 – Reserved 2 – GPS ready (antenna is working, but with no GPS fix) 3 – GPS working (antenna is working and has GPS fix) 4 – GPS sleep (when device is in GPS sleep mode) 5 – Overcurrent (The only condition to get value 5, then antenna is damaged and short circuit)
11	Movement Sensor	0 – not moving, 1 – moving.
12	Odometer Value	Distance between two records: m
13	GSM Operator	Currently used GSM Operator code
14	Speed (Km/h)	Value in km/h, 0 – xxx km/h
15	iButton ID	iButton ID number
16	Mode	0 – home on stop, 1 – home on move, 2 – roaming on stop, 3 – roaming on move, 4 – unknown on stop, 5 – unknown on move
17	GSM Signal	GSM signal level value in scale 1 – 5
18	Deep Sleep	0 – not deep sleep mode, 1 – deep sleep mode
19	Cell ID	GSM base station ID
20	Area Code	Location Area code (LAC), it depends on GSM operator. It provides unique number which assigned to a set of base GSM stations. Max value: 65536
21	Dallas Temperature 1	10 * Degrees (°C), -55 - +115, if 3000 – Dallas error
22	Dallas Temperature 2	10 * Degrees (°C), -55 - +115, if 3000 – Dallas error
23	Dallas Temperature 3	10 * Degrees (°C), -55 - +115, if 3000 – Dallas error
24	Battery Voltage	Voltage: mV
25	Battery Charging Current	Current: mA
26	Ignition	Ignition status indication. Logic: 0 / 1
27	Network Type	0 – 3G network, 1 – 2G network
28	Continuous Odometer	Distance which device has been traveled with ignition ON: m
29	Dallas temperature ID1	1st connected dallas temperature sensor ID
30	Dallas temperature ID2	2nd connected dallas temperature sensor ID
31	Dallas temperature ID3	3rd connected dallas temperature sensor ID
Eventual I/O elements (generate and send record to server only if appropriate conditions are met)
32	Geofence zone 01	Event: 0 – target left zone, 1 – target entered zone
33	Geofence zone 02	Event: 0 – target left zone, 1 – target entered zone
34	Geofence zone 03	Event: 0 – target left zone, 1 – target entered zone
35	Geofence zone 04	Event: 0 – target left zone, 1 – target entered zone
36	Geofence zone 05	Event: 0 – target left zone, 1 – target entered zone
37	Auto Geofence	Event: 0 – target left zone, 1 – target entered zone
38	Trip	1 – trip start, 0 – trip stop
39	Immobilizer	1 – iButton connected
40	Authorized driving	1 – authorized iButton connected
41	Green driving type	1 – harsh acceleration, 2 – harsh braking, 3 – harsh cornering
42	Green driving value	Depending on green driving type: if harsh acceleration or braking – g*100 (value 123 -> 1.23g), if harsh cornering – degrees (value in radians)
43	Over Speeding	At over speeding start km/h, at over speeding end km/h
44	LVCAN Speed	Value in km/h, 0 – 250 km/h
45	LVCAN Accelerator pedal position	Value range: 0-100 %
46	LVCAN Total fuel used	Value range: 0- 99999999 liters* “Total Fuel Used” is sent to server multiplied by 10. Example: if value was 150.5 liters, “1505” will be sent to server.
47	LVCAN Fuel level (liters)	Value range: 0-100 liters
48	LVCAN Engine RPM	Value range: 0-8200 rpm
49	LVCAN Vehicle distance	Value range: 0-2145000000 meters
50	LVCAN Fuel level (proc.)	Value range: 0-100 %
51	LVCAN Program number	Value range: 0-999
52	LVC ModuleID	Value range: 0-max
53	LVC Engine Work Time	Value range: 0-4294967295
54	LVC Engine Work Time (counted)	Value range: 0-4294967295
55	LVC Total Mileage (counted)	Value range: 0-4294967295
56	LVC Fuel Consumed (counted)	Value range: 0-4294967295
57	LVC Fuel Rate	Value range: 0-4294967295
58	LVC AdBlue Level (percent)	Value range: 0-4294967295
59	LVC AdBlue Level (liters)	Value range: 0-255
60	LVC Engine Load	Value range: 0-65535
61	LVC Engine Temperature	Value range: 0-65535
62	LVC Axle 1 Load	Value range: 0-255
63	LVC Axle 2 Load	Value range: 0-65535
64	LVC Axle 3 Load	Value range: 0-65535
65	LVC Axle 4 Load	Value range: 0-255
66	LVC Axle 5 Load	Value range: 0-65535
67	LVC Control State Flags	Value range: 0-255
68	LVC Agricultural Machinery Flags	Value range: 0-255
69	LVC Harvesting Time	Value range: 0-65535
70	LVC Area of Harvest	Value range: 0-65535
71	LVC Mowing Efficiency	Value range: 0-65535
72	LVC Grain Mown Volume	Value range: 0-65535
73	LVC Grain Moisture	Value range: 0-65535
74	LVC Harvesting Drum RPM	Value range: 0-4294967295
75	LVC Gap Under Harvesting Drum	Value range: 0-max
76	LVC Security State Flags	Value range: 0-4294967295
77	LVC Tacho Total Vehicle Distance	Value range: 0-4294967295
78	LVC Trip Distance	Value range: 0-4294967295
79	LVC Tacho Vehicle Speed	Value range: 0-4294967295
80	LVC Tacho Driver Card Presence	Value range: 0-65535
81	LVC Driver1 States	Value range: 0-65535
82	LVC Driver2 States	Value range: 0-255
83	LVC Driver1 Continuous Driving Time	Value range: 0-max
84	LVC Driver2 Continuous Driving Time	Value range: 0-4294967295
85	LVC Driver1 Cumulative Break Time	Value range: 0-4294967295
86	LVC Driver2 Cumulative Break Time	Value range: 0-65535
87	LVC Driver1 Duration Of Selected Acti	Value range: 0-255
88	LVC Driver2 Duration Of Selected Acti	Value range: 0-255
89	LVC Driver1 Cumulative Driving Time	Value range: 0-255
90	LVC Driver2 Cumulative Driving Time	Value range: 0-65535
91	LVC Driver1 ID High	Value range: 0-65535
92	LVC Driver1 ID Low	Value range: 0-65535
93	LVC Driver2 ID High	Value range: 0-65535
94	LVC Driver2 ID Low	Value range: 0-65535
95	LVC Battery Temperature	Value range: 0-65535
96	LVC Battery Level (percent)	Value range: 0-65535

Monitoring

I/O monitoring starts after enabling I/O element and setting up I/O parameters as it is shown below:

Event generating

Events happen when the value of enabled I/O intersects thresholds (enter, exit or on both) predefined by High and Low level thresholds. Table below defines all available values of I/O settings.

Setting	Value
Priority	low, high
High level	maximum threshold
Low level	minimum threshold
Generate event	on interval enter, on interval exit, on both enter and exit
Average constant	1 – 232 (4 Bytes)

Hysteresis

I/O elements can generate events according to hysteresis algorithm. If I/O event operand “Hysteresis” is selected, events will be generated as it is shown in the illustration below (I/O speed is taken as I/O value example):