Changes

no edit summary
Line 44: Line 44:  
Manual CAN data can be configured using “Manual CAN” in CAN tab.
 
Manual CAN data can be configured using “Manual CAN” in CAN tab.
   −
{{{image1|[[Image:FMB630_manual_CAN1.png|700px|left]]}}}
+
{{{image1|[[Image:FMB630_manual_CAN1.png|700px|none]]}}}
    
CAN message ID type: Message ID type two types according to SAEJ1939 standard: Standard ID (value: 0 to 0x7FFh) and Extended ID (value: 0 to 0x1FFFFFFFh).
 
CAN message ID type: Message ID type two types according to SAEJ1939 standard: Standard ID (value: 0 to 0x7FFh) and Extended ID (value: 0 to 0x1FFFFFFFh).
   −
{{{image2|[[Image:FMB630_manual_CAN3.png|200px|left]]}}}
+
{{{image2|[[Image:FMB630_manual_CAN3.png|200px|none]]}}}
      Line 54: Line 54:       −
{{{image3|[[Image:FMB630_manual_CAN2.png|500px|left]]}}}
+
{{{image3|[[Image:FMB630_manual_CAN2.png|500px|none]]}}}
    
Example
 
Example
Line 73: Line 73:  
Pin 2: CAN High signal (blue wire)
 
Pin 2: CAN High signal (blue wire)
   −
{{{image4|[[Image:FMB630_manual_CAN4.png|500px|left]]}}}  
+
{{{image4|[[Image:FMB630_manual_CAN4.png|500px|none]]}}}  
    
In the example {{{model|FMB630}}} will filter all CAN messages with identifier FFFEE9FF (fuel consumption).
 
In the example {{{model|FMB630}}} will filter all CAN messages with identifier FFFEE9FF (fuel consumption).
   −
{{{image5|[[Image:FMB630_manual_CAN5.png|600px|left]]}}}
+
{{{image5|[[Image:FMB630_manual_CAN5.png|600px|none]]}}}
    
CAN parameter configuration example
 
CAN parameter configuration example
Line 145: Line 145:  
The example indicates how fuel consumption message is selected and how configuration impacts this selection.
 
The example indicates how fuel consumption message is selected and how configuration impacts this selection.
   −
{{{image6|[[Image:FMB630_manual_CAN6.png|450px|left]]}}}
+
{{{image6|[[Image:FMB630_manual_CAN6.png|450px|none]]}}}
    
When certain message is filtered, {{{model|FMB630}}} checks which data bytes should be sent to server. Document indicates that 5-8 bytes are used in FMS standard.
 
When certain message is filtered, {{{model|FMB630}}} checks which data bytes should be sent to server. Document indicates that 5-8 bytes are used in FMS standard.
Line 225: Line 225:       −
{{{image7|[[Image:FMB630_manual_CAN7.png|400px|left]]}}}
+
{{{image7|[[Image:FMB630_manual_CAN7.png|400px|none]]}}}
    
Data bytes are filtered by selecting the checkboxes in Output data mask. Note, that configurator has them listed starting with MSB.  
 
Data bytes are filtered by selecting the checkboxes in Output data mask. Note, that configurator has them listed starting with MSB.  
 
After message is filtered it is attached to the data packet and sent to the server. Values are returned in HEX. 00 03 84 23(HEX) = 230435(DEC). Notice, that data resolution is 0.5L/bit gain – value has to be multiplied by 0.5, therefore vehicle used a total 115217,5 liters of fuel.
 
After message is filtered it is attached to the data packet and sent to the server. Values are returned in HEX. 00 03 84 23(HEX) = 230435(DEC). Notice, that data resolution is 0.5L/bit gain – value has to be multiplied by 0.5, therefore vehicle used a total 115217,5 liters of fuel.