Difference between revisions of "Template:FMB1 Blue-tooth OBD dongle"
From Wiki Knowledge Base | Teltonika GPS
| Line 1: | Line 1: | ||
==How to connect OBD II Blue-tooth Dongle to FMB device== | ==How to connect OBD II Blue-tooth Dongle to FMB device== | ||
| − | === | + | ===Blue-tooth settings configuration=== |
[[Image:Fmb120_bt_odbii_settings.png|300px|right]] | [[Image:Fmb120_bt_odbii_settings.png|300px|right]] | ||
| − | Following are the instructions on how to easily prepare | + | Following are the instructions on how to easily prepare Blue-tooth Dongle connection to the {{{model_2|FMB}}} device. First we need to configure {{{model_2|FMB}}} device Blue-tooth settings. These are the required steps: |
| − | * Go to <span style=color:#F6A83E> | + | * Go to <span style=color:#F6A83E>Blue-tooth</span> section similarly to as shown in the figure to the right (position 1). |
* Turn on BT Radio by pressing <span style=color:#F6A83E>Enable (visible)</span> (position 2). "Local name" (position 3) will automatically be "{{{model|FMB1YX}}}_last 7 imei digits", you can leave it or type your own name. | * Turn on BT Radio by pressing <span style=color:#F6A83E>Enable (visible)</span> (position 2). "Local name" (position 3) will automatically be "{{{model|FMB1YX}}}_last 7 imei digits", you can leave it or type your own name. | ||
* Set ''Security Mode'' (position 4) to <span style=color:#F6A83E>PIN only</span> or <span style=color:#F6A83E>None</span> (you could select <span style=color:#F6A83E>PIN + MAC list</span> or <span style=color:#F6A83E>MAC list only</span> security mode but in this case you need to type external device MAC address in ''Authorized Devices MAC List'' (position 7). | * Set ''Security Mode'' (position 4) to <span style=color:#F6A83E>PIN only</span> or <span style=color:#F6A83E>None</span> (you could select <span style=color:#F6A83E>PIN + MAC list</span> or <span style=color:#F6A83E>MAC list only</span> security mode but in this case you need to type external device MAC address in ''Authorized Devices MAC List'' (position 7). | ||
* Set connection mode to <span style=color:#F6A83E>OBDII</span> (position 5). | * Set connection mode to <span style=color:#F6A83E>OBDII</span> (position 5). | ||
| − | * Set ''External Name'' as your | + | * Set ''External Name'' as your Blue-tooth OBD II device name for proper device identification and connection to it. In this example OBDII device name is "DONGLE", at least 2 characters are needed to recognize it and connect to it. For better and faster adapter identification in network you could enter a full device name. You could check your OBDII adapter Blue-tooth name by scanning nearby Blue-tooth devices using a mobile phone or a computer with Blue-tooth adapter. |
* Go to <span style=color:#F6A83E>OBD II</span> in main menu and select priority and others parameters visible in the following figure. | * Go to <span style=color:#F6A83E>OBD II</span> in main menu and select priority and others parameters visible in the following figure. | ||
| Line 16: | Line 16: | ||
* Now you can disconnect {{{model_2|FMB}}} device from the configurator. | * Now you can disconnect {{{model_2|FMB}}} device from the configurator. | ||
| − | ===Connecting to | + | ===Connecting to Blue-tooth OBD II dongle=== |
---- | ---- | ||
| − | After this configuration OBDII dongle can be connected to {{{model_2|FMB}}} device. Turn on ignition, then turn on its | + | After this configuration OBDII dongle can be connected to {{{model_2|FMB}}} device. Turn on ignition, then turn on its Blue-tooth connection. For pairing follow dongle instructions. OBDII device notification about paired Blue-tooth connection depends on the specific model. If you later restart {{{model_2|FMB}}} device it will automatically reconnect to this dongle. |
| − | ===Supported | + | ===Supported Blue-tooth OBD II dongles=== |
---- | ---- | ||
| − | {{{model_2|FMB}}} module works with | + | {{{model_2|FMB}}} module works with Blue-tooth OBD II dongles which are based on ELM327 or STN1110 chips.<br/>Comparison of these chips is presented in the image below: |
[[Image:Elm317_stn1110_comp.png|400px|none]] | [[Image:Elm317_stn1110_comp.png|400px|none]] | ||
Latest revision as of 06:48, 5 October 2018
How to connect OBD II Blue-tooth Dongle to FMB device
Blue-tooth settings configuration
Following are the instructions on how to easily prepare Blue-tooth Dongle connection to the FMB device. First we need to configure FMB device Blue-tooth settings. These are the required steps:
- Go to Blue-tooth section similarly to as shown in the figure to the right (position 1).
- Turn on BT Radio by pressing Enable (visible) (position 2). "Local name" (position 3) will automatically be "FMB1YX_last 7 imei digits", you can leave it or type your own name.
- Set Security Mode (position 4) to PIN only or None (you could select PIN + MAC list or MAC list only security mode but in this case you need to type external device MAC address in Authorized Devices MAC List (position 7).
- Set connection mode to OBDII (position 5).
- Set External Name as your Blue-tooth OBD II device name for proper device identification and connection to it. In this example OBDII device name is "DONGLE", at least 2 characters are needed to recognize it and connect to it. For better and faster adapter identification in network you could enter a full device name. You could check your OBDII adapter Blue-tooth name by scanning nearby Blue-tooth devices using a mobile phone or a computer with Blue-tooth adapter.
- Go to OBD II in main menu and select priority and others parameters visible in the following figure.
- After all these steps press Save to device to save configuration (position 8 in the top right hand figure).
- Now you can disconnect FMB device from the configurator.
Connecting to Blue-tooth OBD II dongle
After this configuration OBDII dongle can be connected to FMB device. Turn on ignition, then turn on its Blue-tooth connection. For pairing follow dongle instructions. OBDII device notification about paired Blue-tooth connection depends on the specific model. If you later restart FMB device it will automatically reconnect to this dongle.
Supported Blue-tooth OBD II dongles
FMB module works with Blue-tooth OBD II dongles which are based on ELM327 or STN1110 chips.
Comparison of these chips is presented in the image below:
