Difference between revisions of "FMU126 RS-232"

From Wiki Knowledge Base | Teltonika GPS
m (Protected "FMU126 RS-232" ([Edit=Allow only administrators] (indefinite) [Move=Allow only administrators] (indefinite)))
Line 1: Line 1:
−
==RS-232 Interface==
+
==RS-232 / RS-485 modes==
−
RS-232 supports full-duplex communication which means the data can be both sent and received at the same time as they use separate transmission lines. Most of the modes are the same as for [[FMB125_RS-232_and_RS-485#RS-485_modes|RS-485]].
+
Available modes for RS-232 and RS-485 interfaces:
−
FMU126 RS-232 connection diagram is shown on the figure above.
 
  
−
===RS-232 modes===
+
{| class="wikitable" style="text-align:center; background-color:#ffffff;"
 +
|- style="text-align:left;"
 +
! rowspan="2" style="text-align:center; vertical-align:middle; font-weight:bold; background: #0054A6; color: white;" | Interface
 +
! colspan="13" style="text-align:center; background: #0054A6; color: white;" | Mode
 +
|-
 +
| Log Mode
 +
| NMEA
 +
| LLS
 +
| LCD
 +
| RFID HID
 +
| RFID MF7
 +
| Garmin FMI
 +
| TCP/UDP Ascii
 +
| TCP/UDP Binary
 +
| TCP/UDP Ascii Buffered
 +
| TCP/UDP Binary Buffered
 +
| Mercury C4
 +
| ULF202 Fuel Sensor
 +
|-
 +
| style="vertical-align:middle;" | RS-232
 +
| ✔
 +
| ✔
 +
| ✔
 +
| ✔
 +
| ✔
 +
| ✔
 +
| ✔
 +
| ✔
 +
| ✔
 +
| ✔
 +
| ✔
 +
| ✔
 +
| ✔
 +
|-
 +
| style="vertical-align:middle;" | RS-485
 +
| ✔
 +
| ✔
 +
| ✔
 +
|
 +
|
 +
|
 +
|
 +
| ✔
 +
| ✔
 +
|
 +
|
 +
|
 +
|
 +
|}
  
−
Log mode, NMEA, LLS, TCP ASCII and TCP Binary modes are identical to those of [[FMB125_RS-232_and_RS-485#RS-485_modes|RS-485]]. In RS-232 LLS mode only one LLS fuel level sensor can be connected. Additionally TCP ASCII Buffered and TCP Binary Buffered modes are available.
+
====Log mode====
 +
In this mode via RS-232 or RS-485 interface prints the {{{model|FMX125}}} device log and does not respond to commands.<br />
  
−
*RS-232 LCD mode:
+
====GNSS NMEA mode====
 +
In NMEA mode via RS-232 or RS-485 interface {{{model|FMX125}}} prints GNSS NMEA log and does not respond to commands.<br />
  
−
In this mode user is able to communicate with the server through terminal. A link between FMB device and the server has to be established for this mode to function properly.
+
====LLS mode====
 +
In LLS mode RS-232 supports one and RS-485 supports up to five - each of which has a receiver ID.<br/>
  
 +
====TCP (ASCII/Binary) modes====
  
−
*RS-232 RFID HID/RFID MF7 mode:
+
In ''TCP Ascii/Binary'' mode all data received from the external device is sent directly to the server. Data is encapsulated in codec 12 format. ''TCP Binary'' Mode has a delay of 30 ms, if no data is received for 30 ms, data is sent to the server. ''TCP Ascii'' mode waits for the End of Line (EOL) character (0x0D0A, \r\n, <CR><LF>) to pack data and send it to the server.
  
−
The difference between RFID HID Mode and RFID MF7 Mode is that in RFID MF7 Mode FMB125 understands RFID messages that are in hexadecimal text format and RFID HID Mode interpretes messages that are in binary format. The type of RFID message sent to FMB125 depends on the RFID reader. For example, RFID MF7 mode message looks like "$aa$02$03$04$17$89$00$01" while HID mode message is of following format: "1213141519".
+
''TCP Ascii Buffered'' and ''TCP Binary Buffered'' modes are used to collect data from RS232 and save it in the buffer if there is no link with the server and data cannot be sent immediately. When the link is established and there is data to transmit, then RS232 data from the buffer is transmitted after all records are sent. Data is sent in codec 13 protocol. Note. That in ''TCP Ascii'' and ''TCP Binary'' modes device sends data from the external device only to the main server. In Buffered modes – to both main and backup/duplicate servers.  
  
−
The selected mode has to correspond to the RFID reader's mode.
+
{| class="nd-othertables_2" style="width:100%;"
−
[[Image:RS-232 MODES.gif]]
+
|-
−
Please contact your local sales representative for more information about RFID IDs and devices.  
+
!
 +
! TCP Binary/TCP ASCII mode
 +
! TCP Binary/TCP ASCII Buffered mode
 +
|-
 +
| '''Data is saved in buffer'''
 +
| No
 +
| Yes
 +
|-
 +
| '''Data sending protocol'''
 +
| Codec 12
 +
| Codec 13*
 +
|-
 +
| '''Timestamp'''
 +
| Not using
 +
| Is using*
 +
|-
 +
| '''To which server is sent'''
 +
| Main
 +
| Main and backup
 +
|}
 +
''*If the Timestamp parameter is enabled, then Codec 13 is used for data sending. Otherwise, Codec 12 is used.''
 +
<br></br>
 +
 
 +
Short video explaining TCP binary mode:
 +
[[File:TCP Binary vid.mp4|1080px|none]]
 +
<br></br>
 +
Short video explaining TCP Ascii mode:
 +
[[File:TCP ASCII vid.mp4|1080px|none]]
 +
 
 +
=====TCP Binary settings=====
 +
TCP Binary has a setting Prefix. It is possible to set Prefix 1, Prefix 2, or Prefix 3. These prefixes can be used separately or in unison.
 +
To configure this setting a value from 0 to 255 in decimal has to be entered. The device will convert this value to HEX and compare the 1st, 2nd, or 3rd byte from incoming data. If the values do not match, the device will not accept incoming data.
 +
 
 +
Video explaining TCP Binary settings:<br>
 +
[[File:TCP Binary prefixes.mp4|1080px|none]]
  
−
<br />
+
=====Message Timestamp=====
 +
[[File:Timestamp.gif|right]] Message Timestamp parameter is used to determine if it is necessary to include timestamp in RS-232 TCP packet when sending to server. If parameter is Enabled, then Codec 13 is used for data sending. Otherwise, Codec 12 is used.
  
−
*RS-232 Garmin mode:
+
=====Codec 12/13 Packet Merge=====
 +
This additional option configures the device to merge RS-232 records into a single packet instead of sending many separate packets.[[File:MERGE.gif|right]] This functionality only affects '''TCP Binary Buffered''' or '''TCP Ascii Buffered''' RS232 modes.
  
−
Garmin provides a Fleet Management Interface Tool Kit, once FMB125 is connected to the navigator it enables the driver to have a "screen" in their vehicle for real-time navigation and messaging, and offers job dispatch capabilities to help them be more efficient.<br />FMB125 and Garmin operational diagram is shown on the figure below.
+
When enabled, the device will merge saved RS-232 records together into a single data packet until it is able to send it to the server.
−
[[Image:Fmb125_garmin_block.png|800px|none]]
+
This optimizes RS-232 data sending by not having to send each RS-232 record separately. If the amount of saved RS-232 data exceeds the maximum 4 bytes of data in one Codec 12 packet, the device will start saving incoming RS-232 data into a new record.
  
−
*RS-232 TCP Binary/TCP ASCII mode:
+
===== RS-232 / RS-485  CMD ID=====
 +
This parameter is used when {{{model|}}} is sending RS232/RS485 packet to a server, it overrides command type value in Codec12/Codec13 with user defined CMD ID value (1 - 14). {{{model|}}} behavior when it receives different CMD ID (Type) values in GPRS packet from server.
 +
[[File:CMD.gif|right]]
  
−
In TCP ASCII/Binary mode all data received from external device is sent directly to server. Data is encapsulated in codec 12 format. TCP Binary Mode has a delay of 30 ms, if no data is received for 30 ms, data is sent to the server. TCP ASCII mode waits for the End of Line (EOL) character (0x0D0A, \r\n) to pack data and send it to the server
+
When {{{model|}}} receives these CMD ID values in the GPRS packet it behaves accordingly:
  
−
*RS-232 TCP Binary Buffered/TCP ASCII Buffered mode:
+
{| class="wikitable" style="width:70%;"
 +
|+
 +
! style="width:10%;border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" | CMD ID
 +
! style="width:10%;border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: center;" | Functionality
 +
|-
 +
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |5
 +
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |Parse Codec12/Codec14 packet from the server
 +
|-
 +
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |7
 +
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |Forward packet meant for Garmin system
 +
|-
 +
|-
 +
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |14
 +
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |Forward packet to external device via uart using RS232/RS485
 +
|-
 +
|-
 +
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |16
 +
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: center; vertical-align: center; background: white;" |Forward packet to paired Bluetooth device
 +
|-
 +
|}
 +
<br></br>
  
−
TCP ASCII Buffered and TCP Binary Buffered modes are used to collect data from RS232 and save it in buffer if there is no link with server and data cannot be sent immediately. When link is established and there is data to transmit, then RS232 data from buffer is transmitted after all records are sent. Data is sent in codec 13 protocol.
+
==RS-232 Modes==
−
Note. That in TCP ASCII and TCP Binary modes device sends data from external device only to main server. In Buffered modes – to both main and backup/duplicate servers.
 
−
Message timestamp:
 
−
Message Timestamp parameter is used to determine if it is necessary to include timestamp in RS232 TCP packet when sending to server. If parameter is enabled, then Codec 13 is used for data sending. Otherwise, Codec 12 is used.
 
−
<br />
 
  
−
====RS-232 TCP Binary settings====
+
====RS-232 LCD mode====
−
[[Image:RS-232 TCP BINARY SETTINGS.gif]] 
+
In this mode, the user is able to communicate with the server through the terminal. A link between the FMB device and the server has to be established for this mode to function properly.
  
−
TCP Binary has a setting Prefix. It is possible to set Prefix 1, Prefix 2 or Prefix 3. These prefixes can be used seperately or in unison.
+
To communicate from terminal to server - in terminal send command -  <code>WT^W <text></code>
−
To configure this setting a value from 0 to 255 in decimal has to be entered. Device will convert this value to HEX and compare the 1st, 2nd or 3rd byte from incoming data. If the values do not match, device will not accept incoming data.
 
  
−
Example:<br>
+
To communicate with the server to the terminal send command - <code>#DO DAT= <text></code> packet in [https://wiki.teltonika-gps.com/view/Teltonika_Data_Sending_Protocols#Codec_12 Codec12 protocol]
−
Incoming packet through RS232/RS485 using TCP Binary/TCP Binary Buffered mode -  <font color="red">50</font> <font color="green">72</font> <font color="blue">65</font> 66 69 78 20 57 6f 72 6b 69 6e 67
 
−
<ul>
 
−
<li>If Prefix 1 is set to 80 in decimal, it is equal to <font color="red">50</font> in HEX.
 
−
<ul><li>FMB device will then check the 1st byte of incoming data and compare to the set Prefix 1.</li></ul></li>
 
−
<li>If Prefix 2 is set to 114 in decimal, it is equal to <font color="green">72</font> in HEX.<br>
 
−
<ul><li>FMB device will then check the 2nd byte of incoming data and compare to the set Prefix 2.</li></ul></li>
 
−
<li>If Prefix 3 is set to 101 in decimal, it is equal to <font color="blue">65</font> in HEX.<br>
 
−
<ul><li>FMB device will then check the 3rd byte of incoming data and compare to the set Prefix 3.</li></ul></li>
 
−
</ul>
 
−
When values match, data will be accepted and saved to Buffer (using TCP Binary Buffered mode) or sent to server (using TCP Binary mode).<br>
 
  
−
Incoming packet through RS232/RS485 using TCP Binary/TCP Binary Buffered mode - <font color="red">50</font> <font color="green">0</font> <font color="blue">65</font> 66 69 78 20 57 6f 72 6b 69 6e 67
+
====RS-232 RFID HID/RFID MF7 mode====
−
<ul>
+
The difference between RFID HID Mode and RFID MF7 Mode is that in RFID MF7 Mode {{{model|}}} understands RFID messages that are in hexadecimal text format and RFID HID Mode interprets messages that are in binary format. The type of RFID message sent to {{{model|}}} depends on the RFID reader. For example, the RFID MF7 mode message looks like <code>$aa$02$03$04$17$89$00$01</code> while HID mode message is of the following format: <code>1213141519</code>
−
<li>If Prefix 1 is set to 80 in decimal, it is equal to <font color="red">50</font> in HEX.
+
 
−
<ul><li>FMB device will then check the 1st byte of incoming data and compare to the set Prefix 1.</li></ul></li>
+
The selected mode has to correspond to the RFID reader's mode.
−
<li>If Prefix 2 is set to 114 in decimal, it is equal to <font color="green">72</font> in HEX.<br>
+
Please contact your local sales representative for more information about RFID IDs and devices.
−
<ul><li>FMB device will then check the 2nd byte <font color="green">0</font> of incoming data and compare to the set Prefix 2.</li></ul></li>
+
 
−
</ul>
+
====RS-232 Garmin mode====
−
Since Prefix 2 does not match incoming 2nd byte, data will not be accepted.
+
Garmin provides a Fleet Management Interface Tool Kit, once {{{model|}}} is connected to the navigator it enables the driver to have a "screen" in their vehicle for real-time navigation and messaging and offers job dispatch capabilities to help them be more efficient.<br />{{{model|}}} and Garmin operational diagram is shown on the figure below.
 +
[[Image:FMX125_GARMIN_BLOCK.png|900px|none]]
  
 
==Garmin protocols==
 
==Garmin protocols==
−
The following is a list of protocols supported and the corresponding list of features/benefits. FMU126 can fully support Fleet Management Interface (FMI) versions up to 2.1. Other or higher versions may be supported, but Teltonika is not responsible for the changes made by Garmin, which may affect the function of FMU126 and Garmin products. For more information about Garmin products and FMI versions, please refer to https://www.garmin.com/en-US/fleet-ready-navigators/. Notice that some Garmin products use different connection cables than others.
+
The following is a list of protocols supported and the corresponding list of features/benefits. {{{model|FMB125}}} can fully support Fleet Management Interface (FMI) versions up to 2.1. Other or higher versions may be supported, but Teltonika is not responsible for the changes made by Garmin, which may affect the function of {{{model|FMB125}}} and Garmin products. For more information about Garmin products and FMI versions, please refer to https://www.garmin.com/en-US/fleet-ready-navigators/. Notice that some Garmin products use different connection cables than others.
−
 
 
−
===Standard protocols===
 
  
 +
'''Standard protocols'''
 +
------------------
 
Text Message Protocol:
 
Text Message Protocol:
  
Line 77: Line 172:
 
*Garmin can also provide a yes/no box below the text of the message to enable a quicker response;
 
*Garmin can also provide a yes/no box below the text of the message to enable a quicker response;
 
*Messages can be up to 199 characters long;
 
*Messages can be up to 199 characters long;
−
*Messages can also be generated from device and sent to dispatcher/office;
+
*Messages can also be generated from the device and sent to dispatcher/office;
−
*Messages received will be notified to driver through a pop-up alert on Garmin screen;
+
*Messages received will be notified to the driver through a pop-up alert on the Garmin screen;
 
*Garmin provides a "virtual keyboard" for text communication.
 
*Garmin provides a "virtual keyboard" for text communication.
  
 
Stop (Destination) Protocol:
 
Stop (Destination) Protocol:
  
−
*Garmin can display a list of Stops/Jobs reported to the device in a separate category called "My Stops";
+
* Garmin can display a list of Stops/Jobs reported to the device in a separate category called "My Stops";
−
*Driver has ability to navigate directly to Stop from the list;
+
*Driver has the ability to navigate directly to Stop from the list;
−
*Garmin can provide status of a current Stop in progress;
+
* Garmin can provide status of a current Stop in progress;
 
*Garmin can indicate whether the driver has stopped at the location;
 
*Garmin can indicate whether the driver has stopped at the location;
 
*Garmin can inform how far the driver has progressed through the list of Stops;
 
*Garmin can inform how far the driver has progressed through the list of Stops;
−
*Garmin can provide confirmation that the driver has received a particular Stop, familiarized himself/herself with its details or removed it from the list;
+
*Garmin can provide confirmation that the driver has received a particular Stop, familiarized himself/herself with its details, or removed it from the list;
 
*Can provide confirmation that a Stop has been reached.
 
*Can provide confirmation that a Stop has been reached.
  
Line 103: Line 198:
 
Data Deletion Protocol:
 
Data Deletion Protocol:
  
−
*Dispatcher/office has the ability to wipe clean the data on Garmin PND;
+
* Dispatcher/office has the ability to wipe clean the data on Garmin PND;
−
*It allows to clean messages in inbox and remove stops.
+
*It allows to clean messages in the inbox and remove stops.
−
 
 
−
===Enhanced protocols===
 
  
 +
'''Enhanced protocols'''
 +
------------------
 
Canned Responses/Messages:
 
Canned Responses/Messages:
  
 
*Fleet managers can communicate by sending up to 200 "canned" responses from the server to be stored directly on Garmin devices;
 
*Fleet managers can communicate by sending up to 200 "canned" responses from the server to be stored directly on Garmin devices;
−
*Up to 50 of these canned responses can be utilized for any given scenarios;
+
*Up to 50 of these canned responses can be utilized for any given scenario;
 
*Drivers can store up to 120 canned messages, eliminating the need to type while driving.
 
*Drivers can store up to 120 canned messages, eliminating the need to type while driving.
  
Line 117: Line 212:
  
 
*Up-to-the-minute communications that allow drivers to automatically send status updates;
 
*Up-to-the-minute communications that allow drivers to automatically send status updates;
−
*Driver's units can store up to 16 status indicators such as start/stop shift, on/off break etc.
+
*Driver's units can store up to 16 status indicators such as start/stop shift, on/off break, etc.
  
−
===Supported features on TAVL client application===
+
'''Supported features on TAVL client application'''
−
TAVL client application lets user use the following features of Garmin FMI:
+
------------------
 +
TAVL client application lets users use the following features of Garmin FMI:
  
 
*Text messaging;
 
*Text messaging;
 
*Destination message;
 
*Destination message;
 
*ETA request.
 
*ETA request.
 +
'''
 +
'''Text messaging'''
 +
------------------
 +
The text messaging feature lets the user communicate with the driver (the user that operates the Garmin device) by sending text messages via GPRS.
  
−
===Text messaging===
+
'''Destination message'''
−
Text messaging feature lets user communicate with the driver (user that operates Garmin device) by sending text messages via GPRS.
+
------------------
−
 
+
Destination message is used to inform the driver of a new destination. When the Garmin device receives a destination message from the server it displays it as a Stop to the driver and also gives the driver the ability to start navigating to the Stop location. A new destination in the TAVL client is represented as a Geozone so a new Geozone (as destination) has to be created first.
−
===Destination message===
 
−
Destination message is used to inform the driver of a new destination. When Garmin device receives a destination message from the server it displays it as a Stop to the driver and also gives the driver an ability to start navigating to the Stop location. New destination in TAVL client is represented as a Geozone so a new Geozone (as destination) has to be created first.
 
−
 
 
−
===ETA request message===
 
−
''Estimated Time of Arrival'' request message is used when user wants to know an expected arrival time to currently active destination and the distance (in meters) from current object location to the destination.
 
  
−
[[Category:FMU126 Manual]]
+
'''ETA request message'''
 +
------------------
 +
''Estimated Time of Arrival'' request message is used when the user wants to know an expected arrival time to the currently active destination and the distance (in meters) from the current object location to the destination.

Revision as of 08:56, 6 December 2021

RS-232 / RS-485 modes

Available modes for RS-232 and RS-485 interfaces:

Interface Mode
Log Mode NMEA LLS LCD RFID HID RFID MF7 Garmin FMI TCP/UDP Ascii TCP/UDP Binary TCP/UDP Ascii Buffered TCP/UDP Binary Buffered Mercury C4 ULF202 Fuel Sensor
RS-232 ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔
RS-485 ✔ ✔ ✔ ✔ ✔

Log mode

In this mode via RS-232 or RS-485 interface prints the FMX125 device log and does not respond to commands.

GNSS NMEA mode

In NMEA mode via RS-232 or RS-485 interface FMX125 prints GNSS NMEA log and does not respond to commands.

LLS mode

In LLS mode RS-232 supports one and RS-485 supports up to five - each of which has a receiver ID.

TCP (ASCII/Binary) modes

In TCP Ascii/Binary mode all data received from the external device is sent directly to the server. Data is encapsulated in codec 12 format. TCP Binary Mode has a delay of 30 ms, if no data is received for 30 ms, data is sent to the server. TCP Ascii mode waits for the End of Line (EOL) character (0x0D0A, \r\n, <CR><LF>) to pack data and send it to the server.

TCP Ascii Buffered and TCP Binary Buffered modes are used to collect data from RS232 and save it in the buffer if there is no link with the server and data cannot be sent immediately. When the link is established and there is data to transmit, then RS232 data from the buffer is transmitted after all records are sent. Data is sent in codec 13 protocol. Note. That in TCP Ascii and TCP Binary modes device sends data from the external device only to the main server. In Buffered modes – to both main and backup/duplicate servers.

TCP Binary/TCP ASCII mode TCP Binary/TCP ASCII Buffered mode
Data is saved in buffer No Yes
Data sending protocol Codec 12 Codec 13*
Timestamp Not using Is using*
To which server is sent Main Main and backup

*If the Timestamp parameter is enabled, then Codec 13 is used for data sending. Otherwise, Codec 12 is used.

Short video explaining TCP binary mode:



Short video explaining TCP Ascii mode:

TCP Binary settings

TCP Binary has a setting Prefix. It is possible to set Prefix 1, Prefix 2, or Prefix 3. These prefixes can be used separately or in unison. To configure this setting a value from 0 to 255 in decimal has to be entered. The device will convert this value to HEX and compare the 1st, 2nd, or 3rd byte from incoming data. If the values do not match, the device will not accept incoming data.

Video explaining TCP Binary settings:

Message Timestamp
Timestamp.gif

Message Timestamp parameter is used to determine if it is necessary to include timestamp in RS-232 TCP packet when sending to server. If parameter is Enabled, then Codec 13 is used for data sending. Otherwise, Codec 12 is used.

Codec 12/13 Packet Merge

This additional option configures the device to merge RS-232 records into a single packet instead of sending many separate packets.

MERGE.gif

This functionality only affects TCP Binary Buffered or TCP Ascii Buffered RS232 modes.

When enabled, the device will merge saved RS-232 records together into a single data packet until it is able to send it to the server. This optimizes RS-232 data sending by not having to send each RS-232 record separately. If the amount of saved RS-232 data exceeds the maximum 4 bytes of data in one Codec 12 packet, the device will start saving incoming RS-232 data into a new record.

RS-232 / RS-485 CMD ID

This parameter is used when is sending RS232/RS485 packet to a server, it overrides command type value in Codec12/Codec13 with user defined CMD ID value (1 - 14). behavior when it receives different CMD ID (Type) values in GPRS packet from server.

CMD.gif

When receives these CMD ID values in the GPRS packet it behaves accordingly:

CMD ID Functionality
5 Parse Codec12/Codec14 packet from the server
7 Forward packet meant for Garmin system
14 Forward packet to external device via uart using RS232/RS485
16 Forward packet to paired Bluetooth device



RS-232 Modes

RS-232 LCD mode

In this mode, the user is able to communicate with the server through the terminal. A link between the FMB device and the server has to be established for this mode to function properly.

To communicate from terminal to server - in terminal send command - WT^W <text>

To communicate with the server to the terminal send command - #DO DAT= <text> packet in Codec12 protocol

RS-232 RFID HID/RFID MF7 mode

The difference between RFID HID Mode and RFID MF7 Mode is that in RFID MF7 Mode understands RFID messages that are in hexadecimal text format and RFID HID Mode interprets messages that are in binary format. The type of RFID message sent to depends on the RFID reader. For example, the RFID MF7 mode message looks like $aa$02$03$04$17$89$00$01 while HID mode message is of the following format: 1213141519

The selected mode has to correspond to the RFID reader's mode. Please contact your local sales representative for more information about RFID IDs and devices.

RS-232 Garmin mode

Garmin provides a Fleet Management Interface Tool Kit, once is connected to the navigator it enables the driver to have a "screen" in their vehicle for real-time navigation and messaging and offers job dispatch capabilities to help them be more efficient.
and Garmin operational diagram is shown on the figure below.

FMX125 GARMIN BLOCK.png

Garmin protocols

The following is a list of protocols supported and the corresponding list of features/benefits. FMB125 can fully support Fleet Management Interface (FMI) versions up to 2.1. Other or higher versions may be supported, but Teltonika is not responsible for the changes made by Garmin, which may affect the function of FMB125 and Garmin products. For more information about Garmin products and FMI versions, please refer to https://www.garmin.com/en-US/fleet-ready-navigators/. Notice that some Garmin products use different connection cables than others.

Standard protocols

Text Message Protocol:

  • Allows text messages sent to the device to be displayed in "inbox" on navigation unit;
  • Garmin can provide a confirmation that message was read;
  • Garmin can also provide a yes/no box below the text of the message to enable a quicker response;
  • Messages can be up to 199 characters long;
  • Messages can also be generated from the device and sent to dispatcher/office;
  • Messages received will be notified to the driver through a pop-up alert on the Garmin screen;
  • Garmin provides a "virtual keyboard" for text communication.

Stop (Destination) Protocol:

  • Garmin can display a list of Stops/Jobs reported to the device in a separate category called "My Stops";
  • Driver has the ability to navigate directly to Stop from the list;
  • Garmin can provide status of a current Stop in progress;
  • Garmin can indicate whether the driver has stopped at the location;
  • Garmin can inform how far the driver has progressed through the list of Stops;
  • Garmin can provide confirmation that the driver has received a particular Stop, familiarized himself/herself with its details, or removed it from the list;
  • Can provide confirmation that a Stop has been reached.

Estimated Time of Arrival Protocol:

  • Dispatcher/office can request the ETA of the current Stop/job in progress;
  • Garmin can notify about the actual time of arrival as well as the distance remaining to a Stop.

Auto-Arrival at Stop Protocol:

  • This feature is used to tell Garmin PND to automatically detect that it has arrived at a Stop and then to prompt the driver if he/she would like to mark the Stop as done and begin navigating to a next Stop on the list;
  • Auto-arrival can be determined by how long the unit is stopped close to the destination (in the case driver has to park and walk) or by how close the unit needs to be to the destination before the Auto-arrival feature is activated.

Data Deletion Protocol:

  • Dispatcher/office has the ability to wipe clean the data on Garmin PND;
  • It allows to clean messages in the inbox and remove stops.

Enhanced protocols

Canned Responses/Messages:

  • Fleet managers can communicate by sending up to 200 "canned" responses from the server to be stored directly on Garmin devices;
  • Up to 50 of these canned responses can be utilized for any given scenario;
  • Drivers can store up to 120 canned messages, eliminating the need to type while driving.

Status Protocol:

  • Up-to-the-minute communications that allow drivers to automatically send status updates;
  • Driver's units can store up to 16 status indicators such as start/stop shift, on/off break, etc.

Supported features on TAVL client application

TAVL client application lets users use the following features of Garmin FMI:

  • Text messaging;
  • Destination message;
  • ETA request.

Text messaging

The text messaging feature lets the user communicate with the driver (the user that operates the Garmin device) by sending text messages via GPRS.

Destination message

Destination message is used to inform the driver of a new destination. When the Garmin device receives a destination message from the server it displays it as a Stop to the driver and also gives the driver the ability to start navigating to the Stop location. A new destination in the TAVL client is represented as a Geozone so a new Geozone (as destination) has to be created first.

ETA request message

Estimated Time of Arrival request message is used when the user wants to know an expected arrival time to the currently active destination and the distance (in meters) from the current object location to the destination.

Retrieved from "https://wiki.teltonika-gps.com/index.php?title=FMU126_RS-232&oldid=68989"