Warranty guidelines

Introduction

TELTONIKA TELEMATICS gives guarantee for its products for a period of 24 months. All batteries carry a reduced 6 month warranty period. If a product fails within mentioned warranty period the product can be:

• Repaired;
• Replaced with a new product;
• Replaced with an equivalent repaired product fulfilling the same functionality;
• Replaced by an equivalent product if the production is discontinued.

During the return merchandise authorization (RMA) part of the warranty process, an engineer examines the information provided by a client in an RMA request form in order to determine whether the equipment is eligible repair, replacement or a refund. The RMA request form contains company, addressing and malfunctioning product information and must be filled out by the product's owner and approved by a Teltonika Telematics engineer before returning a product.

Hardware Issues

The table below contains information on which hardware related issues are covered by the warranty service and which issues are not:

Hardware issue	Do devices need to be sent under RMA?	Next step
Device does not start. LED does not blink at all when device is powered up (10-30 V DC); If client ensures that device does have 10-30 V DC power supply and still does not start, such device should be sent to warranty.	YES, if this issue is true	Steps to fill out RMA form: 1. Login to HelpDesk: https://viphelpdesk.teltonika.lt/ 1. 2. Create new ticket and fill in the information about the non-functioning product. 3. Follow the instructions from the engineer and wait until your form is approved. 4. After the form is approved you will get it through E-mail. 5. Print the RMA form and send it together with the shipment. 1 If you do not have a VIP Helpdesk account, please contact your sales manager.
Visible physical damage (FMXXXX damaged, GPS antenna damaged...): Visible physical damage on device case; Visible physical damage on device PCB; Visible deformation of internal battery;
Digital input is not working: Connect DIN to power supply „+“, and check if DIN status changes. If not – send to warranty
1-wire short circuit: Check 1-wire device type (maybe not supported device (ibutton, temp. sensor); Check connection scheme; Check terminal log (overcurrent message); Measure voltage on 1-wire PWR and GND (should be 3.6V);	YES, if all the points are false, but FM still does not send data
No GPS (GPS overcurrent, physical GPS antenna damage): Check terminal log, look for overcurrent messages; If overcurrent message is still present after GPS antenna change – send FM to warranty; If overcurrent message is not present after GPS antenna change – change GPS antenna;	YES, if overcurrent message is still present after GPS antenna change
No overcurrent messages in log, but still no GPS FIX. Make sure GPS antenna is seeing clear sky; Check NMEA log .log_nmea:x [0- disable; 1- enable] (May be no signal); If another FM device gets GPS FIX with the same antenna – send device to warranty.	YES, if another FM device gets GPS FIX with the same antenna
Sim card failure. FM does not see SIM card (bended sim holder, 3G sim card): Check SIM card itself, if there is no physical bending; Check if SIM card is seen by cell phone or other FM device; Check if sim card is 2G (GSM) capable; Check modem version (.info), try updating modem to the latest one, if modem version is old; Check if PIN code is not set; Check if device is working with another SIM card, another operator SIM card; Check if GSM antenna is connected.	YES, if none of the mentioned points helps
Visible physical damage on the external GPS antenna; Visible physical damage on the external cellular antenna.	NO, if at least one issue is true, offer to change an antenna

Firmware Issues

The table below contains information on which firmware related issues are covered by the warranty service and which issues are not:

Firmware issue	Eligible for warranty?	Remote connection status
Device is in boot mode (status LED is blinking fast) – send instruction for device recovery.	YES, if unable to revocer device manually	Contact support
Firmware blocked (security firmware) – check firmware description, if it is possible to reflash this firware to base FW.	YES, if unable to reflash to base firmware
Modem failure (Modem initializing, Modem Seems to be Dead).	YES, if the solution does not help	Fill out RMA request form

The recommended course of action when firmware issues are encountered is to contact your sales representative if the device was purchased directly from Teltonika or contact Teltonika support if VIP HelpDesk access is provided to you. If you purchased the device elsewhere, contact the distributor that sold you the device.

IMPORTANT: in any of the defined cases, please contact your sales representative before sending the device(s) to warranty.