Difference between revisions of "Teltonika Configuration Tool Installation manual"
| Line 47: | Line 47: | ||
#Click '''Install'''. wait for the progress bar to be completed. | #Click '''Install'''. wait for the progress bar to be completed. | ||
#And finally click '''close''' to exit the installation. | #And finally click '''close''' to exit the installation. | ||
| − | |||
| − | |||
| Line 95: | Line 93: | ||
*This will then take you to the configuration screen. | *This will then take you to the configuration screen. | ||
| − | [[Image:Create_New_Configuration.gif|center|alt=|thumb| | + | [[Image:Create_New_Configuration.gif|center|alt=|thumb|1100x1100px]] |
| Line 102: | Line 100: | ||
*To start configuring a connected device, click the "Configure". | *To start configuring a connected device, click the "Configure". | ||
| − | [[Image:Configure_Connected_Device.gif|center|alt=|thumb| | + | [[Image:Configure_Connected_Device.gif|center|alt=|thumb|1100x1100px]] |
Revision as of 15:04, 17 March 2023
Introduction
To start using the Telematics Configuration Tool (TCT), you must meet the minimum system requirements to install the software on your computer. The installation process is straightforward and does not differ from other desktop software.
Minimum System Requirements
OS: Windows 7; Windows 10; Windows 11
CPU: Intel or AMD processor with 64-bit support
Disk Storage: 500 MB of free disk space
Memory: 500 MB of free RAM
Graphics: DirectX 9 or later with WDDM 1.0 driver
Internet: Ethernet port or Wi-Fi w/ network access for auto-update
Telematics Configuration Tool Download Link
To download the Teltonika Configurator Tool please click here.
Telematics Configuration Tool Installation
- Run the TelematicsConfigurationTool.Setup.exe with admin privileges' to begin the installation.
- Accept the license agreement to install the TCT.
- Once you accept the license agreement, you can choose if the TCT software will be available for all users or only to you (currently login user).
- Select the location from where you want to install the TCT, by default, It is installed the program files, but you can install it in any location you preferred.
- The progress bar will start until the installation is completed.
- Click Finish to complete the installation.
Virtual-COM Port Drivers Installation
Virtual-COM Port Driver is a serial communication port driver for Teltonika Telematics device, It is one of the requirements for the TCT to work properly, without this driver the TCT will not detect your FM device.
- To download the Virtual-COM Port Driver please click here
- To Install the Virtual-COM Port Driver please follow the steps below.
- Run the Virtual-COM Port Driver with admin privileges' to begin the installation.
- Click the checkbox for Teltonika COM Driver
- Click next and modify/configure the destination folder for installation.
- Click Install. wait for the progress bar to be completed.
- And finally click close to exit the installation.
IMPORTANT NOTES
- During the installation the Windows SmartScreen might pop up.
- If the Windows SmartScreen pop up, you must click on More info.
- Additional information about the application will display:
- Take note that the application name should be TelematicsConfigurationTool.Setup.x.x.xx.exe.
- x represents the version of the setup (.exe file), so it can differ according to the installer version that you have.
- You must confirm that the publisher is indeed from TELTONIKA TELEMATICS.
- If everything is correct, please click Run anyway
- After confirmation the installation setup start will immediately.
Offline vs Online Configuration
Offline Configuration refers to creating configuration without any device connected, you can save this Configuration File and then load it to the device remotely or when there is an available device connected. On the other hand, online Configuration refers to creating a configuration with a device connected whereas you can directly save the changes on the device.
Creating Offline Configuration File
- To create a new configuration file, choose/search for the device you want from the list.
- Click the "Configure" button.
- This will then take you to the configuration screen.
Creating Online Configuration File
- To start configuring a connected device, click the "Configure".
Opening An Existing Configuration File
- To open an existing configuration file, click on the three dots and click "Open".
- Select the configuration file and click "Open".
- TCT will load the configuration file and you will be able to edit and save your changes.
