Difference between revisions of "FTC921 Features"
| Line 1: | Line 1: | ||
| − | + | ==Overspeeding== | |
| − | |||
| − | |||
[[File:FTC921_Overspeeding.png|right|300 px]] | [[File:FTC921_Overspeeding.png|right|300 px]] | ||
| Line 11: | Line 9: | ||
*Max speed – it is the maximum allowed speed that can be reached. If the speed exceeded configured value, then the event will occur. | *Max speed – it is the maximum allowed speed that can be reached. If the speed exceeded configured value, then the event will occur. | ||
| − | + | ==Trip== | |
[[File:FTC921_Trip.png|right|300 px]] | [[File:FTC921_Trip.png|right|300 px]] | ||
| Line 17: | Line 15: | ||
| − | + | ==Odometer settings== | |
[[File:FTC921_Odometer_settings.png|right|300 px]] | [[File:FTC921_Odometer_settings.png|right|300 px]] | ||
| Line 23: | Line 21: | ||
| − | + | ==Unplug detection== | |
| − | |||
| − | |||
[[File:FTC921_Unplug_detection.png|right|300 px]] | [[File:FTC921_Unplug_detection.png|right|300 px]] | ||
| Line 35: | Line 31: | ||
'''GPRS'''. | '''GPRS'''. | ||
| − | |||
| − | + | ==Static navigation== | |
[[File:FTC921_Static_navigation.png|right|300 px]] | [[File:FTC921_Static_navigation.png|right|300 px]] | ||
| Line 44: | Line 39: | ||
| − | + | ==Digital output overcurrent recovery== | |
[[File:FTC921_Digital_output_overcurrent_recovery.png|right|300 px]] | [[File:FTC921_Digital_output_overcurrent_recovery.png|right|300 px]] | ||
[[Category:FTC921 Configuration]] | [[Category:FTC921 Configuration]] | ||
Revision as of 14:19, 29 May 2023
Main Page > Basic Trackers > FTC921 > FTC921 Configuration > FTC921 FeaturesOverspeeding
When vehicle speed exceeds configured maximum speed value the scenario is activated, and an event record is generated and digital output status is changed to 1 when configured.
Detected speed has to be greater than configured max speed +3% of configured max speed for the overspeeding event to start. To stop overspeeding event detected speed has to be lower than configured max speed -3% of configured max speed.
Configurable parameters:
- Priority – defines the priority of overspeeding scenario: 0 – disabled, 1 – low, 2 – high, 3 – panic.
- Max speed – it is the maximum allowed speed that can be reached. If the speed exceeded configured value, then the event will occur.
Trip
Trip' section offers user to configure the Trip feature. Trip starts when Ignition according Ignition source is ON and Movement according Movement source is ON and also 'Start Speed' is exceeded. Start Speed defines the minimum GPS speed in order to detect Trip start.
Ignition OFF Timeout is the timeout value to detect Trip end once the Ignition (configured ignition source) is off.
I/O Trip Odometer must be enabled to use Distance counting mode feature. When it is set to Continuous, Trip distance is going to be counted continuously (from Trip start to Trip end) and written to I/O Trip Odometer value field. When Trip is over and the next Trip begins, Trip Odometer value is reset to zero.
When Mode is set to Between Records, the distance is going to be counted between every record made. This value is written to I/O Trip Odometer value field and is reset to zero every new record until the Trip ends. If later all Odometer values are summed up manually, the distance driven during the whole duration of the Trip can be obtained.
Odometer settings
Calculation Source allows to choose Odometer calculation source between GNSS, OBD.
Odometer Value sets the starting total odometer value.
Unplug detection
An event will be generated when FMB1YX is unplugged from external power or plugged back in again. Priority
- Disable - disable scenario.
- Low Priority - when low priority event is triggered, device makes additional record with indication of event cause.
- High Priority - module makes additional record with High priority flag and sends event packet immediately to the server by
GPRS.
Static Navigation Mode is a filter, which filters out track jumps when the object is stationary.
If the Static navigation filter is disabled, it will apply no changes to GPS data. If the Static navigation filter is enabled, it will filter changes in GPS position if no movement (configured movement source) or ignition (configured ignition source) is detected (depends on what static navigation settings are selected: movement, ignition or both sources). It allows filtering GPS jumps when an object is parked (is not moving) and GPS position is still traced.
Digital output overcurrent recovery
