Difference between revisions of "DashCam Troubleshoot"
From Wiki Knowledge Base | Teltonika GPS
(Created page with "__TOC__ ==DashCam Checks== *Check RS232 configuration, baud rate, etc. Default values should be set for the DashCam. *See if both cameras are working. Try sending separate pic...") |
|||
| Line 13: | Line 13: | ||
*Camera might have a problem detecting SD card. Format microSD card using a FAT file system (FAT32 or exFAT). Try different cards. Try re-inserting the cards while the camera is turned on. Also, keep in mind that the smallest supported card is 16 GB. | *Camera might have a problem detecting SD card. Format microSD card using a FAT file system (FAT32 or exFAT). Try different cards. Try re-inserting the cards while the camera is turned on. Also, keep in mind that the smallest supported card is 16 GB. | ||
*Physical camera restart. Disconnect the camera’s power supply and disconnect from the FMX125 device. Leave the camera for a few minutes like that and power it on but do not connect to the FMX125 for a few minutes. After some time, reconnect the device and check if the camera responds. | *Physical camera restart. Disconnect the camera’s power supply and disconnect from the FMX125 device. Leave the camera for a few minutes like that and power it on but do not connect to the FMX125 for a few minutes. After some time, reconnect the device and check if the camera responds. | ||
| − | + | ||
| − | + | **Check whether Codec8 Extended is enabled. Without Codec8 Extended, parameters of AVL ID 497, 499 '''WILL''' not be sent. | |
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | **Check whether Codec8 Extended is enabled. Without Codec8 Extended, parameters of AVL ID 497 | ||
[[Image:Data_protocol.gif|300px]] | [[Image:Data_protocol.gif|300px]] | ||
Latest revision as of 11:37, 26 June 2023
Main Page > Video Solutions > Teltonika DashCam > DashCam TroubleshootDashCam Checks
- Check RS232 configuration, baud rate, etc. Default values should be set for the DashCam.
- See if both cameras are working. Try sending separate picture requests and check the result. “camreq:1:1” for the front camera and “camreq:1;2” for the rear camera. Possible responses to "camreq" command - Camera request command
Check camera IO values in the configurator.
- If the camera seems to be enabled, check the SD card content. See if there are any files and review the footage using TF CardVideoPlayer v1.14. If there is some footage from the time the camera was turned on. The actual time in the camera might differ, therefore check older dates to see if there are any videos.
- If some recent video files were found, it means that the camera is working, but not responding to RS232 commands. Otherwise, the camera is either not working or not responding to commands and does not detect SD card.
Possible solutions
- Camera might have a problem detecting SD card. Format microSD card using a FAT file system (FAT32 or exFAT). Try different cards. Try re-inserting the cards while the camera is turned on. Also, keep in mind that the smallest supported card is 16 GB.
- Physical camera restart. Disconnect the camera’s power supply and disconnect from the FMX125 device. Leave the camera for a few minutes like that and power it on but do not connect to the FMX125 for a few minutes. After some time, reconnect the device and check if the camera responds.
- Check whether Codec8 Extended is enabled. Without Codec8 Extended, parameters of AVL ID 497, 499 WILL not be sent.
If nothing helps and the camera is still not working or working incorrectly, log data using 2;3;9;1 filter and collect the log files.
