TEST-DM

Parameter list (short)

https://wiki.teltonika-gps.com/view/FTC134_Features#Parameter_list

Parameter list (full)

PARAMETER ID	NAME	DESCRIPTION	UNITS/VALUES	TYPE	MIN	MAX	DEFAULT
11816	Private mode deactivation triggers	Private mode deactivation triggers. When a trigger is activated it deactivates the private mode. Implemented using bit mask so that multiple choices could be selected.	0 - no trigger; 1 - Towing detected; 2 - Unplug detected; 3 - Towing or Unplug detected; 4 - Crash detected; 5 - Towing or Crash detected; 6 - Unplug or Crash detected; 7 - Towing, Unplug or Crash detected; 8 - Autogeofence triggered; 9 - Towing or Autogeofence triggered; 10 - Unplug or Autogeofence triggered; 11 - Towing, Unplug or Autogeofence triggered; 12 - Crash or Autogeofence triggered; 13 - Towing, Crash or Autogeofence triggered; 14 - Unplug, Crash or Autogeofence triggered; 15 - Towing, Unplug, Crash or Autogeofence triggered	Uint16	0	15	15
900007	Speed limit	Speed threshold which determines when to generate speeding start/stop events.	km/h	Uint16	0	1000	0
1024900	Network jamming detection	The feature detects GSM jamming, initiates actions using an output, and helps to prevent vehicle theft when jamming devices are used. A low signal level is not equal to GSM jamming, the device recognizes these events.	0 = Disable; 1 = Low priority; 2 = High priority	Uint8	0	2	0
899901 (DOUT1) 899911 (DOUT2) 899921 (DOUT3)	Activation timing	Select Activation timing when the event will be triggered. Control mode - Persistent: Outside activation timing, selected DOUT will start being controlled while the device is outside of the geozone and will stop being controlled while the device is inside of the geozone. If the device is outside of multiple geozones, selected DOUT will continue being controlled until the device enters one of the geozones. Inside activation timing, selected DOUT will start being controlled while the device is inside the geozone and will stop being controlled while the device is outside of the geozone. If Output control according to speed limit is set, selected DOUT will start being controlled while the device is exceeding the speed limit inside the geozone. If the device is inside multiple geozones, selected DOUT will continue being controlled until the device is outside of all geozones (or stops exceeding the speed limit, if configured). Control mode - Event: Outside activation timing, selected DOUT will be triggered once you exit the configured geozone. Inside activation timing, selected DOUT will be triggered once you enter the configured geozone.	1=Outside 2=Inside	Uint8	1	2	1
empty	empty	empty	empty	empty	empty	empty	1000000

AVL ID list

AVL ID	NAME	BYTES	TYPE	MIN	MAX	MULTIPLIER	UNITS	DESCRIPTION
16	Total Odometer	4	Unsigned	0	2147483647	-	m	Virtual odometer value
69	GNSS Status	1	Unsigned	0	3	-	-	0 - GNSS OFF; 1 - GNSS ON with fix; 2 - GNSS ON without fix; 3 - GNSS sleep
181	GNSS PDOP	2	Unsigned	0	500	-	m	GNSS position dilution of precision. Normal PDOP is below 3 – the lower the number, the more accurate reported location is.
13377	Neighbouring Cell 2 RSSI	1	Unsigned	0	63	-	dB	Signal strength of Cell #2. Included in records as Permanent I/O when LBS mode is configured as "Location Source".
157	Manual Geofence Speeding event	1	Unsigned	0	1	-	-	0 - Speeding stop event; 1 - Speeding start event
empty	empty	empty	empty	empty	empty	empty	empty	empty

Pinout

PIN COLOR NAME DESCRIPTION 1 Red VCC Power supply (+8-32V V DC) (+) 2 Gray DOUT3 Digital output channel 3 3 White DIN3/AIN3 Digital input channel 3 / Analog input channel 3 4 WhiteGreen DIN4/AIN4/DGS Digital input channel 4 / Analog input channel 4 / Ground sense 5 Yellow DIN1/AIN1 Digital input 1 / Analog input 1 6 WhiteBlue INPUT6 TX EXT (LVCAN – TX) 7 Black GND Ground (-) 8 WhiteOrange DOUT1 Digital output channel 1 9 Purple DOUT2 Digital output channel 2 10 Blue 1WIRE POWER +3.8 V output for 1-Wire devices 11 Green DIN2/AIN2/1WIRE DATA Digital input channel 2 / Analog input 2 / Data for 1-Wire devices 12 WhiteYellow INPUT5 RX EXT (LVCAN – RX)

PCN

ITEM	VALUE
Change details
Change type	Firmware update
Description	Key improvements from last production firmware are listed in errata: [[{{{model}}} Firmware Changelog]]
Previous firmware version	0.26.2
New firmware version	2.1.1
Change reason	{{{model}}} base firmware version update
Product release date	2025 June
Affected products
Model	{{{model}}}
Affected order codes	All order codes
Order code change	New firmware version
Impact
Risk assessment	During the transition period, clients might receive devices manufactured with the previous firmware version.