Template:FMB System settings

System settings have 9 configurable parameters:

• Sleep Settings, where user can choose sleep mode;
• Ignition Source, where user can choose between power voltage, digital input 1, accelerometer and engine RPM as ignition sources. More than one ignition source can be selected at the same moment. User can select movement start and movement stop delay time - those parameters are used when accelerometer is selected as ignition source. Ignition status is used in power management and the following functionalities: eco driving, excessive idling, fuel consumption, over speeding, towing and trip functionalities.
• Object Motion Detection Settings, where user can configure 4 ways how FMB120 detects movement, and change its working mode (for working modes, read section Data acquisition settings). Other functionalities that depend from movement source: power manager, fuel consumption and trip.
• Static Navigation Settings, where user can turn static navigation on or off. Additionally, user can choose what source is used (movement or ignition) to activate/deactivate static navigation.
• Records Settings, where user can enable or disable records when GPS is not available (no time synchronization).
• GNSS Source settings, where user can choose the necessary satellite system.
• LED Indication, where user can turn on or off the indication LEDs.
• Battery Charge Mode, where user can choose when battery will be charged: On Need (battery will be charged anytime when it needs to be charged) and After Ignition ON (battery will be charged only when ignition is on).
• Analog Input Value Range, where user can choose analog input range of 10 V or 30 V (currently 10 V is in fact a 30 V range).
• Time Synchronization settings, where user can choose which source(s) to use for FMB120 time synchronization. User has a choice to use only one synchronization source Disable (GPS only), allow synchronization from both the GNSS and NTP server (NTP), select synchronization through GNSS and GSM operator (NITZ) or from all three sources (when NITZ+NTP is selected). User can select which NTP server (it is possible to configure up to two servers) and what time period to use to resynchronize time.

Movement source	Vehicle on Stop mode	Vehicle Moving mode
Ignition (recommmended)	If ignition (ignition source) is logic low	If ignition (ignition source) is logic high
Movement (movement sensor)	Internal movement sensor does not detect movement.	Internal movement sensor detects movement.
GPS	GPS fix is available and vehicle speed is lower than 5 km/h.	GPS fix is available and vehicle speed is higher than 5 km/h.
	While GPS fix is unavailable, Object Motion Detection Settings are working like in Msensor mode.
CAN speed	If speed from BT OBDII dongle is equal 0 km/h.	If speed from BT OBDII dongle is higher that 0 km/h.

Static Navigation mode is a filter, which filters out track jumps when the object is stationary. If static navigation filter is disabled, it will apply no changes to GPS data. If static navigation filter is enabled, it will filter changes in GPS position if no movement (configured movement source) or ignition (configured ignition source) is detected (depends on what static navigation settings is selected: movement, ignition or both sources). It allows filtering GPS jumps when object is parked (not moving) and GPS position is still traced.

In GNSS source Settings user can configure which GNSS system(s) to use.
User has choice to use only one system of GPS, Glonass, Galileo or Beidou. Also it is possible to choose two or three systems together. One exception is that you cannot combine Beidou and Glonass systems together.

Selected source(s)	ID
Beidou only	01
Glonass only	02
Galileo only	04
Galileo + Beidou	05
Galileo + Glonass	06
GPS only	08
GPS + Beidou	09
GPS + Glonass	10
GPS + Galileo	12
GPS + Galileo + Beidou	13
GPS + Galileo + Glonass	14

Examples of NON-configurable GNSS sources:

• Glonass + Beidou
• Galileo + Glonass + Beidou
• GPS + Glonass + Beidou
• GPS + Galileo + Glonass + Beidou