Template:FTX First Start

Small and smart waterproof tracker

KNOW YOUR DEVICE

HOW TO REMOVE COVER

	Device casing is designed to be water-proof and meets IP69K requirements. Please note that once the cover is fully clipped, it will require additional plastic pry tools to be opened! Please make sure to review the short walkthrough video for more details:

SET UP YOUR DEVICE

	Physical SIM card insertion/removal must be performed when device is powered off – external voltage and internal battery disconnected. Otherwise, the SIM card might be damaged or device will not detect it.

FTC305 CASING VERSION

Insert Nano-SIM card as shown with PIN request disabled. Make sure that Nano-SIM card cut-off corner is pointing towards the SIM slot.
Connect the main 7-pin cable connector to the socket on PCB.
Attach the cover. Please note: Before attaching cover, ensure the device is configured via USB. The USB port on the PCB will be inaccessible once the cover is fully attached.
Device is ready to be mounted.

FTC305 NON-CASING VERSION

You will receive your device with thermal cambric covering the PCB. Remove the thermal cambric.
Insert Nano-SIM card as shown with PIN request disabled. Make sure that Nano-SIM card cut-off corner is pointing towards the SIM slot.
Connect the main 7-pin cable connector to the socket on PCB.
Re-attach thermal cambric. Please note: You can heat the thermal cambric for it to fully seal the PCB, however, after heating it, you will no longer be able to access SIM and USB slots unless the cambric is removed. You will still be able to configure the device using FOTA WEB or Bluetooth.
External GNSS and Cellular antennas are included in the packaging box. Connect the GNSS antenna to adapter that is connected to PCB. Then connect the Cellular antenna to LTE adapter that is connected to PCB.
External battery is included in the packaging box. Connect the battery to battery adapter that is connected to PCB.
Device is ready to be mounted.

File:FTC305 non-casing setup.png

PC CONNECTION (WINDOWS)

Connect device to computer using USB Type-C cable.
Please note: FTC305 device does not require an external power supply for configuration. However, without external power, data sending and other cellular connectivity functions will not work. If you want to test the device on a table, it is advised to power up FTC305 with a DC voltage (10-97V) power supply using power wires.
Install USB driver, see "HOW TO INSTALL USB DRIVERS (WINDOWS)".

HOW TO INSTALL USB DRIVERS (WINDOWS)

Please download COM port drivers from here.
Extract and run TeltonikaCOMDriver.exe.
Click Next in driver installation window.
In the following window click Install button.
Setup will continue installing the driver and eventually the confirmation window will appear. Click Finish to complete the setup.

CONFIGURATION (WINDOWS)

At first, FTC881 device will have default factory settings set. These settings should be changed according to the user's needs. Main configuration can be performed via Teltonika Configurator tool (TCT).

LED BEHAVIOUR DESCRIPTION

This section is an explanation of LED indications on FTC881 device.

NAVIGATION LED INDICATIONS

Behaviour	Meaning
Permanently switched on	GNSS signal is not received
Blinking every second	Normal mode, GNSS is working
Off	GNSS is turned off because: Device is not working or Device is in sleep mode
Blinking fast constantly	Device firmware is being flashed

STATUS LED INDICATIONS

Behaviour	Meaning
Blinking every second	Normal mode
Blinking every two seconds	Sleep mode
Blinking fast for a short time	Modem activity
Off	Device is not working or Device is in boot mode

PINOUT

PIN NUMBER	PIN NAME	DESCRIPTION
1	VCC	(Red) Power supply (+10-90 V DC) (+).
2	GND	(Black) Ground (-).
3	DIN1	(Yellow) Digital input, channel 1. DEDICATED FOR IGNITION INPUT. Input range: 7.5-90 V DC.
4	AIN1	(Grey) Analog input, channel 1. Input range: 0-90 V DC.
5	DOUT1	(White) Digital output. Open collector output. Max. 0,5 A DC.

MOUNTING RECOMMENDATIONS

DEVICE FASTENING

Locate the battery in your vehicle. If present remove the battery cover to access the battery.
There is a double sided tape on the back of the device, use it to attach the device on the battery, so that the GNSS antenna and LEDs indicators are facing up.

CONNECTING POWER SOURCE

Device power wire is designed to be directly connected to the positive terminal fastener of the vehicle battery.

CONNECTING GROUND WIRE

Device ground wire is designed to be directly connected to the negative terminal fastener of the vehicle battery.

[[Category:{{{model}}}]]