OBD Device Debugging

From Wiki Knowledge Base | Teltonika GPS

Note: This page is in works!

Solution applies for these devices FMB001 FMC001 FMM001 FMB003 FMC003 FMM003

OBD Data Debugging

Device does not read listed OBD OEM parameters

Capturing OBD logs from FMX00X via OEM Reset

Requesting for OBD OEM Support

 If you have a vehicle that is not listed in the OBD OEM Supported Vehicle List or you are facing problems with OBD OEM in General - follow the log capturing guide below.

Capturing OBD logs from FMX00X with Filters

  1. Make sure that the CAN adapter is connected properly to the vehicle and to the FMB1YX series device.
  2. Start vehicle engine.
  3. Send following SMS commands to FMX1YX device:
    • If you have set SMS login and password:login pass log2sdfilterset 0;2;3;4;1
    • If SMS login and password are not set leave two spaces before command: aalog2sdfilterset 0;2;3;4;1

      If command log2sdfilterset was sent correctly you should receive SMS Response:Enabled Trace Filters:5 then you can restart the device

  4. If FW version is 03.27.10 or higher cpureset command is not necessary to enable the filters. On lower versions cpureset is mandatory.
    • If you have set SMS login and password: login pass cpureset

    • If SMS login and password are not set leave two spaces before command:aacpureset

      Filter description:

      Filter 0 - default filters (No additional data)

      Filter 4 - turn on CAN adapter filter

      Filter 1 - save installed filters to memory after restart

  5. After the SMS response message CAN adapter log capturing has been started.
  6. Wait at least 5 minutes to get enough CAN bus data and turn off vehicle engine.
  7. Download captured log (dump) files.

Basic OBD OEM Configuration

Data protocol.gif

  • Configure Ignition Settings according to your vehicle.
 If the vehicle is equipped with Internal Combustion Engine, it is recommended to keep Ignition Source settings with Power Voltage. Otherwise, if it is an EV/HV, set Ignition Source settings as Accelerometer.
  • Check if OBD Feature is Enabled
 For Internal Combustion Engine & HV OBD (Auto) must be Checked. If it is an EV, use Non-OBD compliant and enter VIN Source Manually.
  • Now it is necessary to enable OBD OEM parameters according to the vehicle list

750px

 Let's say we have a VW Polo 2016. The list tells that Mileage (AVL ID 389), Fuel Level in Liters (AVL ID 390) and Fuel Level in % (AVL ID 48) is supported.
  • Enable the listed parameters

OBD Fuel.png

 Enabled Fuel Level in % (AVL ID 48) Parameter.

OBD OEM.png

 Enabled Mileage (AVL ID 389) and Fuel Level in Liters (AVL ID 390) Parameter.
  • After enabling the parameters proceed with installation of FMX00X device into the OBDII port.
 Once the device is installed, turn on the Ignition and send SMS command web_connect. This will force the device to acquire OBD OEM File from FOTA WEB.

Verify the Status on FOTA WEB

  • Open your FOTA WEB account,
  • Find device by IMEI
Under Details, OBD section, you should see the VIN Number of your vehicle: Under Tasks, you can verify if the file is delivered to the device or not:
Task 5.png  Task 4.png
 Lastly, check your server for the availability of OBD OEM Data.

OBD Feature

OBD Feature for Vehicles with Internal Combustion Engine

OBD Regular AutoVIN.png

 Regular configuration for vehicles with Internal Combustion engines. OBD Feature OBD (Auto), Vin Source (Auto).

OBD Regular ManualVIN.png

 If Auto VIN reading does not work, enter VIN Number manually.

OBD Feature for EVs

OBD EV ManualVIN.png

 Configuration for EVs. OBD Feature Non-OBD compliant, Vin Source (Manual).

Renault & Peugeot Specific FMB003 Information

 If you have Renault or Peugeot vehicle and OBD OEM does not work, check if you have the latest FMB003 Hardware.

Verify FMB003 Hardware Status on FOTA WEB

  • Open your FOTA WEB account,
  • Find device by IMEI
FMB003 OLDHW.png  FMB003 77HW.png
 With this example FMB003OENJ01 is an old hardware and FMB00377NJ01 being a newer one. If Product Code contains - FMB003OE consider new Hardware. Contact your Sales Manager for more information.