EYE FUNCTIONALITIES

Page Description

This page will describe EYE device functionalities, their value flow and required firmware and software versions,

Search device with QR scan

Functionality: Now you can find devices with QR scan by pressing scan button and scanning device QR code.

Firmware: 1.2.1.R.0+

Value: Easier device management

Flow: 1. Tap 2. scan the QR code engraved onto EYE device

Customized Sensor Selection

Functionality: Users can disable sensors reading leaving only the sensors they require.

Firmware: 1.2.10.R.4+

Value: Data saving, battery life can be expanded by disabling accelerometer.

Flow: 1. Connect to EYE device 2. Click "configure" 3. Expand Active sensors tab 4. Uncheck sensors you want to deactivate 4. Save your configuration.

Auto-Disconnect Timer

Functionality: After 2 minutes of inactivity, users will be automatically disconnected from the device. Before disconnection, you will have the option to maintain the connection.

Firmware: 1.2.10.R.4+

Value: Enhanced privacy and energy saving.

Flow: 1. Connect to EYE device 2. Do not perform any saving actions for 2 minutes.

Visible battery voltage

Functionality: Eye App now provides a clear and convenient readout of the battery's voltage level, keeping users informed about their device's power status.

Firmware: 1.2.1.R.0+

Value: Keeping users informed about their device's power status.

Flow: 1. Expand sensor card in the overview screen or connect to the device

12 characters name

Functionality: Users can now assign names of up to 12 characters,

Firmware: 1.2.1.R.0+

Value: A full MAC address can be used as the name.

Flow: 1. Connect to EYE device 2. Click "configure" 3. Expand Name settings drop down 4. Enter desired name 4. Save your configuration.

EYE APP 1.2.0-63

PIN code

Functionality: Eye App will time-out users on for 5 minutes after 5 unsuccessful PIN attempts

Firmware: 1.2.1.R.0 to 1.2.8.R.2

Value: Enhanced privacy

Flow: 1. Tap the selected device to connect to it 2. Enter PIN incorrectly, fail to enter PIN correctly 4 more times 3. Wait 5 minutes for timeout to end.

PUK code

Functionality: Eye App will block users that fail PIN 10 times.

Firmware: 1.2.9.R.8+

Value: Enhanced privacy

Lock flow: 1. Tap the selected device to connect to it 2. Enter PIN incorrectly, fail to enter PIN correctly 4 more times 3. Wait 5 minutes for timeout to end. 4. Tap the selected device to connect to it 5. Enter PIN incorrectly, fail to enter PIN correctly 4 more times. 6. Requirement to enter PUK code will now appear. PUK code is provided by support.

Unlock flow: 1. Tap the blocked device to connect to it 2. Enter PUK correctly 3. You will be connected, PIN will be reset to default

PUK code unlock

SW version requirements	EYE APP: 1.2.0-60+ Firmware: 1.2.9.R.8+
Step No.
Short step desc.	Tap the blocked device to connect to it	Enter PUK	Connected
Additional desc.			PIN automatically resets to default
Successful attempt at functionality visual
Step desc.	Tap the selected device to connect to it	Enter PUK incorrectly	Fail to enter PIN correctly 4 more times
Additional desc.		PUK is rejected and you can only go back or enter correct PUK
Failed attempt at functionality visual

Hibernate mode:

Wake up:

SW version requirements	Firmware: 1.2.9.R.8+
Step No.	1-3	4
Short step desc.	Attach magnet to sleeping device and wait for LED to blink.	Device starts broacasting
Additional desc.		Now device is discoverabled, scannable, connectable via BLE.
Successful attempt at functionality visual

Send to sleep:

SW version requirements	EYE APP: 1.2.0-60+ Firmware: 1.2.9.R.8+
Step No.	1	2	3
Short step desc.	While connected and in overview tap "Send device to sleep"	Confirm your selection	Wait for EYE App to disconnect
Additional desc.			Device is no longer connectable or findable until wake up step is performed.
Successful attempt at functionality visual