Template:TMT250 stable FW&SW changelog

VERSION	RELEASE DATE	CONFIGURATOR CHANGES	FIRMWARE CHANGES
55.02.03.Rev.05 1.7.66 B.55.2 R.10	2024-01-30	[CHN] Added new AVL ID's SMS events tab [FIX] Fixed Online vs Offline configuration discrepancies [FIX] Fixed Ultra Deep Sleep naming mismatch [FIX] Fixed Tool Tips inaccuracies [ADD] Added EYE Sensors support settings and filtering by sensors name and MAC address [CHN] Changed device wiki links to teltonika-gps [CHN] Moved EYE Sensor I/O settings to Bluetooth 4.0 tab [FIX] Fixed Roaming operator/Operator Black List .csv file importing [FIX] Fixed Maximum GPS Satellites Quantity parameter (ID: 906) value [ADD] Added configurable accelerometer sensitivity settings [ADD] Added continuous battery charging mode [CHN] Changed minimum BLE scan start period value	[CHN] Added possibility to send SMS AVL ID event to few numbers [FIX] Fixed sensors scanning issue, then Beacon Detection is Disabled or set to beacons No Send mode. [ADD] Added CSQ level parameter [ADD] Added ‚ shutdown‘ SMS/GPRS command to power off device [FIX] Added configurable accelerometer sensitivity options in sleep mode [FIX] Fixed ‚btgetlist 3‘ SMS command [FIX] Changed battery voltage measurement and charging algorithm [ADD] Added EYE Sensor support [ADD] BLE Sensors Custom field data are displayed in decimal now [FIX] Fixed batteries percentage calculation when voltage is Fully charged [FIX] Refactored battery percentage limits checking algorithm [FIX] Fixed battery charging status [FIX] Fixed BT records generation issue, when BLE devices feature is disabled [FIX] Fixed beacon buffer cleanup after the end of BLE scanning or periodic beacon record creation. [FIX] Fixed GSM established LED indication turning off issue [CHN] Changed minimum BLE scan start period configuration value.

VERSION	RELEASE DATE	CONFIGURATOR CHANGES	FIRMWARE CHANGES
55.02.03.Rev 05 1.7.66_B.55.2_R.10	2023-12-13	[CHN] Added new AVL IDs SMS events tab [FIX] Fixed Online vs Offline configuration discrepancies [FIX] Fixed Ultra Deep Sleep naming mismatch [FIX] Fixed Tool Tips inaccuracies [ADD] Added EYE sensors support settings and filtering by sensor's'name and MAC address [CHN] Changed device wiki links to teltonika-gps [CHN] Moved EYE Sensor I/O settings to Bluetooth 4.0 tab. [FIX] Fixed Roaming operator/Operator Black list .csv file importing [FIX] Fixed Maximum GPS Satellites Quantity parameter (ID: 906) value [ADD] Added configurable accelerometer sensitivity settings [ADD] Added continuous battery charging mode [CHN] Changed minimum BLE scan start period value.	[CHN] Added possibility to send SMS AVL ID event to few numbers [FIX] Fixed sensors scanning issue, then Beacon Detection is Disabled or set to beacons No Send mode. [ADD] Added CSQ level parameter [ADD] Added ‚ shutdown‘ SMS/GPRS command to power off device [ADD] Added configurable accelerometer sensitivity options in sleep mode [FIX] Fixed ‚btgetlist 3‘ SMS command [FIX] Changed battery voltage measurement and charging algorithm [ADD] Added EYE sensor support [ADD] BLE sensors Custom field data are displayed in decimal now [FIX] Fixed batteries percentage calculation when voltage is Fully charged [FIX] Refactored battery percentage limits checking algorithm [FIX] Fixed battery charging status [FIX] Fixed BT records generation issue, when BLE devices feature is disabled [FIX] Fixed beacon buffer cleanup after the end of BLE scanning or periodic beacon record creation. [FIX] Fixed GSM established LED indication turning off issue [CHN] Changed minimum BLE scan start period configuration value.


VERSION	RELEASE DATE	CONFIGURATOR CHANGES	FIRMWARE CHANGES
55.01.02.Rev.01 1.6.11_R.30	2021.10.25	Change No Movement/Movement event SMS text Added Race Mode feature	Added Race Mode for GNSS data live tracking Fixed LED indication stuck when Man-Down Cancel button is pressed Fixed FW version display in FOTA WEB Fixed possibility to configure forbidden GNSS source via SMS or GPRS Fixed fake movement events when Low power mode is used Fixed BLE scan stuck when Xiaomi bracelet is used Fixed restarts when Beacon on Demand feature is used for longer time Fixed Alarm call delay issue Fixed FW update issue with XT26G01CWSIGT flash Added XT26G01CWSIGT and GD5F1GQ5UE NAND flash support Changed minimum charging temperature from -10°C to 1°C SMS commands will return time with applied time zone The maximum battery charging temperature changed from 50°C to 45°C Maximum operating temperature changed from 65°C to 59°C
55.00.21.Rev.00 1.6.11_R.26	2021.08.10	'Data Acquisition' tool tips and labels changed. Changed BLE 'Update frequency' name and tool tips. Fixed 'Beacon on demand' labels.	Added possibility to Enable or Disable Mandown/Movement/No Movement features while charging. Accelerometer and movement detection improvements. Fixed invalid SMS number when reporting position after call.
55.00.18.Rev.02 1.6.11_R.23	2021.05.13	No changes	Fixed issue which occurred during manufactory testing phase with Ver.55.00.18.Rev.01 where device could end with GNSS State = 0
55.00.18.Rev.01 1.6.11_R.23	2021.05.07	Increased Beacon List from 25 to 100 Added On Demand Tracking On/Off/Switch button action Added On Demand Tracking event indication settings	Increased Configured beacons count from 25 to 100 If Beacon record sending is configured to be 'Eventual', send only if device sees any beacons Improved Power On/Off feature notifications Power save mode is working with Data Acquisition time 60s and above On Demand Tracking functionality improved with button control and On Demand Tracking event indication
55.00.10.Rev.01 1.6.11_R.16	2020.11.13	Added Last Known Position feature settings Added Power On/Off event settings Added Power off with Power key settings Added Custom BLE I/O parameters	Added Last Known Position feature on HIGH priority event (alarm, amber alert, man-down, etc). When device gains current GPS position after HIGH priority event was generated, device sends another HIGH priority event with updated position and GPS fix timestamp. Reworked GNSS status SMS template. Fixed issue of data acquisition parameters reset to default values.
55.00.07.Rev.09 1.5.15_C.002	2020.10.20	Minor changes	Important change of charging algorithm. This algorithm provides higher safety and prolonging battery’s life longevity. Corrected battery display in percentage Improved charging current from PC.
55.00.07.Rev.07 1.5.15_C.002	2020.09.16	Minor changes	Lowered battery charging current from wall charger to 425mA. Fixed battery LED indication when battery is fully charged.
55.00.07.Rev.02 1.5.15_C.002	2020.03.17	Added Man-Down Event On Exit and On Entrance parameters	Updated Server IP and Port saving procedures. Reworked Generate Event On Exit and On Entrance logic. Reworked handheld devices switching between Charging and Normal modes. Reworked User ID values scan after device is turn off/on. Reworked Button I/O on-click event.
55.00.05.Rev.00 1.5.0_C.007	2020.02.13	Removed unnecessary Low Power parameters Removed unnecessary Time Synchronization settings Implemented On Demand tracking functionality Removed unnecessary Number Check Settings panel Implemented Event Notification functionality Implemented User ID functionality Improved BLE beacon functionality Implemented Beacon List functionality Improved User Interface configuration panel Improved Keyboard configuration panel Implemented Button IO feature Updated default settings	Reworked User Interface configuration. Reworked Keyboard configuration. Implemented Event Notification panel. Implemented Call After Answer functionality Implemented User ID functionality. Implemented On Demand data acquisition functionality. Implemented Button IO Feature. Optimized wake up from deep sleep by movement. Updated default settings. Improved BLE compatibility with beacons.