Changes

==Purpose of CAN adapters LV-CAN200 and ALL-CAN300==

==Purpose of CAN adapters LV-CAN200 and ALL-CAN300==

[[Image:FMB640_can_connx_diagram.png|350px|center]]

[[Image:FMB640_can_connx_diagram.png|350px|none]]

LV-CAN200 is used to read data from light vehicles, while ALL-CAN300 is used to read data from any type of transport: light vehicles, trucks, buses, agriculture transport and other special transport. Using these adapters {{{model|FMB640}}} device is able to collect and send vehicle data.

LV-CAN200 is used to read data from light vehicles, while ALL-CAN300 is used to read data from any type of transport: light vehicles, trucks, buses, agriculture transport and other special transport. Using these adapters {{{model|FMB640}}} device is able to collect and send vehicle data.

SIMPLE-CAN works in the '''listening mode only''', so that not all the data available on the CAN-BUS may be received using this solution. '''The device automatically sets CAN L/H polarity''', but the calibration has to be always performed during installation process. Connection of previously calibrated unit to another car needs new calibration because the reader '''automatically adjusts signal level and speed''' to different CAN buses. The device also '''automatically adapts''' to the found '''noise level'''.

SIMPLE-CAN works in the '''listening mode only''', so that not all the data available on the CAN-BUS may be received using this solution. '''The device automatically sets CAN L/H polarity''', but the calibration has to be always performed during installation process. Connection of previously calibrated unit to another car needs new calibration because the reader '''automatically adjusts signal level and speed''' to different CAN buses. The device also '''automatically adapts''' to the found '''noise level'''.

[[Image:FMB640_simplecan_pinout.png|800px|center]]

[[Image:FMB640_simplecan_pinout.png|800px|none]]

When power supply is connected, the LED shines continuously. It means that device is waiting for calibration. '''Calibration process''' has to be carried out when CAN-BUS twisted pair is tightened on SIMPLE-CAN and when ignition is ON. Please press the switch briefly and wait for the LED to start blinking every second. Automatic calibration process takes up to 10 seconds depending on the vehicle's model. Correct calibration process is confirmed by LED starting to blink every 2 seconds (when the CAN-BUS is active). When the CAN-BUS enters sleep mode, SIMPLE-CAN device also enters sleep mode and takes 1.6mA @ 12V. In the sleep mode LED does not shine. If after calibration process LED shines continuously, it means that device is not calibrated yet, CAN-BUS transmission has failed or ignition during calibration was not ON.

When power supply is connected, the LED shines continuously. It means that device is waiting for calibration. '''Calibration process''' has to be carried out when CAN-BUS twisted pair is tightened on SIMPLE-CAN and when ignition is ON. Please press the switch briefly and wait for the LED to start blinking every second. Automatic calibration process takes up to 10 seconds depending on the vehicle's model. Correct calibration process is confirmed by LED starting to blink every 2 seconds (when the CAN-BUS is active). When the CAN-BUS enters sleep mode, SIMPLE-CAN device also enters sleep mode and takes 1.6mA @ 12V. In the sleep mode LED does not shine. If after calibration process LED shines continuously, it means that device is not calibrated yet, CAN-BUS transmission has failed or ignition during calibration was not ON.

For exact pinout see sticker on Light Vehicles Can adapter.

For exact pinout see sticker on Light Vehicles Can adapter.

[[Image:FMB640_lv-can200_pinout.png|625px|center]]

[[Image:FMB640_lv-can200_pinout.png|625px|none]]

[[Image:FMB640_all-can300_pinout.png|625px|center]]

[[Image:FMB640_all-can300_pinout.png|625px|none]]

{| class="wikitable" style="border-style: solid; border-width: 0px"

{| class="wikitable" style="border-style: solid; border-width: 0px"

===Example===

===Example===

When using older connection schemes where program number displayed as 3-digit program number:

When using older connection schemes where program number displayed as 3-digit program number:

[[Image:FMB640_can_prog_number.png|600px|center]]

[[Image:FMB640_can_prog_number.png|600px|none]]

Using LV-CAN200/ALL-CAN300 Bootloader from soft version 2017-09-27 it is necessary to add "1" to the front of program number:

Using LV-CAN200/ALL-CAN300 Bootloader from soft version 2017-09-27 it is necessary to add "1" to the front of program number:

[[Image:FMB640_can_updater.png|400px|center]]

[[Image:FMB640_can_updater.png|400px|none]]