3,261
edits
Changes
→Configuration
Manual CAN data can be configured using “Manual CAN” in CAN tab.
Manual CAN data can be configured using “Manual CAN” in CAN tab.
{{{image1|[[Image:FMB630_manual_CAN1.png|700px|none]]}}}
{{{image1|[[Image:FMB640_Manual_CAN.png|700px|none]]}}}
CAN message ID type: Message ID type two types according to SAEJ1939 standard: Standard ID (value: 0 to 0x7FFh) and Extended ID (value: 0 to 0x1FFFFFFFh).
CAN message ID type: Message ID type two types according to SAEJ1939 standard: Standard ID (value: 0 to 0x7FFh) and Extended ID (value: 0 to 0x1FFFFFFFh).
{{{image2|[[Image:FMB630_manual_CAN3.png|200px|none]]}}}
{{{image2|[[Image:FMB640_Manual_CAN1.png|200px|none]]}}}
This information is provided only as an example and Teltonika
This information is provided only as an example and Teltonika
takes no responsibility for information accuracy or damage that may be done to the vehicle or {{{model|FMB630}}} module while integrating it.
takes no responsibility for information accuracy or damage that may be done to the vehicle or {{{model|FMB640}}} module while integrating it.
Example:
Example:
All Mercedes Benz Actros 2 models with Vehicle Identification Number (VIN) starting with WDB93 have a possibility to connect {{{model|FMB630}}} module to CAN bus. This can be done by connecting to special PSM module (which may or may not be included in the truck) or ground module of the vehicle. For CAN signal to be available, parameter 520 must be enabled in “kommunikationsschnittstelle” in the vehicle with Mercedes Stardiagnose.
All Mercedes Benz Actros 2 models with Vehicle Identification Number (VIN) starting with WDB93 have a possibility to connect {{{model|FMB640}}} module to CAN bus. This can be done by connecting to special PSM module (which may or may not be included in the truck) or ground module of the vehicle. For CAN signal to be available, parameter 520 must be enabled in “kommunikationsschnittstelle” in the vehicle with Mercedes Stardiagnose.
CAN wires can be found on X5 connector located in the fuse box:
CAN wires can be found on X5 connector located in the fuse box:
Pin 5: CAN Low signal (yellow wire)
Pin 5: CAN Low signal (yellow wire)
{{{image4|[[Image:FMB630_manual_CAN4.png|500px|none]]}}}
{{{image4|[[Image:FMB630_manual_CAN4.png|500px|none]]}}}
In the example {{{model|FMB630}}} will filter all CAN messages with identifier FFFEE9FF (fuel consumption).
In the example {{{model|FMB640}}} will filter all CAN messages with identifier FFFEE9FF (fuel consumption).
{{{image5|[[Image:FMB630_manual_CAN5.png|600px|none]]}}}
{{{image5|[[Image:FMB630_manual_CAN5.png|600px|none]]}}}
{{{image6|[[Image:FMB630_manual_CAN6.png|450px|none]]}}}
{{{image6|[[Image:FMB630_manual_CAN6.png|450px|none]]}}}
When certain message is filtered, {{{model|FMB630}}} checks which data bytes should be sent to server. Document indicates that 5-8 bytes are used in FMS standard.
When certain message is filtered, {{{model|FMB640}}} checks which data bytes should be sent to server. Document indicates that 5-8 bytes are used in FMS standard.
{| class="wikitable"
{| class="wikitable"