174
edits
Changes
Created page with "==CAN \ Tachograph== '''CAN \ Tachograph''' are used to configure device when connection of CAN1 and CAN2 BUS lines are performed. <br> Teltonika recommendations: <br> * FM..."
==CAN \ Tachograph==
'''CAN \ Tachograph''' are used to configure device when connection of CAN1 and CAN2 BUS lines are performed. <br>
Teltonika recommendations: <br>
* FMM640 CAN1 connected to vehicle's FMS(J1939) BUS line<br>
* FMM640 CAN2 connected to vehicle's Tachograph - Instructions can be found on [[FMM640_and_Tachograph_Solution|FMM640 and Tachograph Solution]] wiki page;
==Tachograph Settings==
<br />
'''In FMM640 configurator “CAN/Tachograph” section tachograph settings should be set in order to download files.<br />'''
<br />
DDD download source – to which CAN line tachograph is connected;<br />
<br />
Tachograph ignition source – which DIN is connected to vehicle ignition ("Ignition" parameter - tachograph ignition source will be the same as configured in "System" -> "Ignition Source");<br />
<br />
[[image:FMB640_Tachograph_settings2.gif]]
FMM640 can be wired to Tachograph using instructions provided in [[FMM640_and_Tachograph_Solution|FMM640 and Tachograph Solution]] wiki page.
==WEB Tacho Settings==
'''WEB Tacho Settings''' are used to configure Tacho WEB server to which device periodically connects.
WEB Tacho Settings:<br />
'''Status''' - functionality enabling;<br />
'''Domain''' – server domain where files will be send;<br />
'''Port''' – server port where files will be send;<br />
'''Start delay''' – delay after turning on ignition to start procedure of file sending.<br />
[[image:FMB640_WEB_Tacho.gif]]
==FMS settings==
FMS settings is used to configure FMS source. <br><br>
If you have FMS wired to FMM640 CAN1, FMS source should be selected as CAN1.<br>
If you have FMS wired to FMM640 CAN2, FMS source should be selected as CAN2.
[[image:FMB640_FMS_settings.gif]]
'''CAN \ Tachograph''' are used to configure device when connection of CAN1 and CAN2 BUS lines are performed. <br>
Teltonika recommendations: <br>
* FMM640 CAN1 connected to vehicle's FMS(J1939) BUS line<br>
* FMM640 CAN2 connected to vehicle's Tachograph - Instructions can be found on [[FMM640_and_Tachograph_Solution|FMM640 and Tachograph Solution]] wiki page;
==Tachograph Settings==
<br />
'''In FMM640 configurator “CAN/Tachograph” section tachograph settings should be set in order to download files.<br />'''
<br />
DDD download source – to which CAN line tachograph is connected;<br />
<br />
Tachograph ignition source – which DIN is connected to vehicle ignition ("Ignition" parameter - tachograph ignition source will be the same as configured in "System" -> "Ignition Source");<br />
<br />
[[image:FMB640_Tachograph_settings2.gif]]
FMM640 can be wired to Tachograph using instructions provided in [[FMM640_and_Tachograph_Solution|FMM640 and Tachograph Solution]] wiki page.
==WEB Tacho Settings==
'''WEB Tacho Settings''' are used to configure Tacho WEB server to which device periodically connects.
WEB Tacho Settings:<br />
'''Status''' - functionality enabling;<br />
'''Domain''' – server domain where files will be send;<br />
'''Port''' – server port where files will be send;<br />
'''Start delay''' – delay after turning on ignition to start procedure of file sending.<br />
[[image:FMB640_WEB_Tacho.gif]]
==FMS settings==
FMS settings is used to configure FMS source. <br><br>
If you have FMS wired to FMM640 CAN1, FMS source should be selected as CAN1.<br>
If you have FMS wired to FMM640 CAN2, FMS source should be selected as CAN2.
[[image:FMB640_FMS_settings.gif]]